| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20241007-x1e80100-pwrseq-qcp-v1-3-f7166510ab17@linaro.org>
Date: Mon, 07 Oct 2024 20:22:27 +0200
From: Stephan Gerhold <stephan.gerhold@...aro.org>
To: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>
Cc: Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Abel Vesa <abel.vesa@...aro.org>, Johan Hovold <johan@...nel.org>,
Bartosz Golaszewski <brgl@...ev.pl>,
Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
Subject: [PATCH 3/3] arm64: dts: qcom: x1e80100-qcp: Add WiFi/BT pwrseq
Add the WiFi/BT nodes for QCP and describe the regulators for the WCN7850
combo chip using the new power sequencing bindings. All voltages are
derived from chained fixed regulators controlled using a single GPIO.
The same setup also works for CRD (and likely most of the other X1E80100
laptops). However, unlike the QCP they use soldered or removable M.2 cards
supplied by a single 3.3V fixed regulator. The other necessary voltages are
then derived inside the M.2 card. Describing this properly requires
new bindings, so this commit only adds QCP for now.
Signed-off-by: Stephan Gerhold <stephan.gerhold@...aro.org>
---
arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 144 ++++++++++++++++++++++++++++++
1 file changed, 144 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 1c3a6a7b3ed6..9977c2a505b9 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -17,6 +17,7 @@ / {
aliases {
serial0 = &uart21;
+ serial1 = &uart14;
};
wcd938x: audio-codec {
@@ -254,6 +255,101 @@ vreg_nvme: regulator-nvme {
pinctrl-names = "default";
pinctrl-0 = <&nvme_reg_en>;
};
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_1p9: regulator-wcn-1p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_1P9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_wcn_0p95>;
+ vdddig-supply = <&vreg_wcn_0p95>;
+ vddrfa1p2-supply = <&vreg_wcn_1p9>;
+ vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_wlan_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -684,6 +780,23 @@ &pcie4_phy {
status = "okay";
};
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
&pcie6a {
perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
@@ -877,6 +990,37 @@ wcd_default: wcd-reset-n-active-state {
bias-disable;
output-low;
};
+
+ wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+ pins = "gpio116", "gpio117";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio214";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
};
&uart21 {
--
2.46.0
Powered by blists - more mailing lists