linux-kernel - [PATCH v2 5/6] i2c: nomadik: fix BRCR computation

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20241009-mbly-i2c-v2-5-ac9230a8dac5@bootlin.com>
Date: Wed, 09 Oct 2024 12:23:31 +0200
From: Théo Lebrun <theo.lebrun@...tlin.com>
To: Linus Walleij <linus.walleij@...aro.org>, 
 Andi Shyti <andi.shyti@...nel.org>, Rob Herring <robh@...nel.org>, 
 Krzysztof Kozlowski <krzk+dt@...nel.org>, 
 Conor Dooley <conor+dt@...nel.org>
Cc: linux-arm-kernel@...ts.infradead.org, linux-i2c@...r.kernel.org, 
 devicetree@...r.kernel.org, linux-kernel@...r.kernel.org, 
 Vladimir Kondratiev <vladimir.kondratiev@...ileye.com>, 
 Grégory Clement <gregory.clement@...tlin.com>, 
 Thomas Petazzoni <thomas.petazzoni@...tlin.com>, 
 Tawfik Bayouk <tawfik.bayouk@...ileye.com>, 
 Théo Lebrun <theo.lebrun@...tlin.com>
Subject: [PATCH v2 5/6] i2c: nomadik: fix BRCR computation

Current BRCR computation is:

    brcr = floor(i2cclk / (clkfreq * div))

With brcr: "baud rate counter", an internal clock divider,
 and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
 and clkfreq: desired bus rate,
 and div: speed-mode dependent divider (2 for standard, 3 otherwise).

Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
  then brcr = floor(48MHz / (3.4MHz * 3)) = 4
   and resulting bus rate = 48MHz / (4 * 3) = 4MHz

Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
  then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
   and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz

The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:

    brcr = floor(i2cclk / (clkfreq * div)) + 1

If we redo the above examples:

Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
  then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
   and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz

Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
  then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
   and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz

This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.

This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).

Signed-off-by: Théo Lebrun <theo.lebrun@...tlin.com>
---
 drivers/i2c/busses/i2c-nomadik.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c
index 8f52ae4d6285af2dd2b3dc7070672757e831a019..b2b9da0b32ed903c080f4bdc427ea0dd7b031b49 100644
--- a/drivers/i2c/busses/i2c-nomadik.c
+++ b/drivers/i2c/busses/i2c-nomadik.c
@@ -454,9 +454,12 @@ static void setup_i2c_controller(struct nmk_i2c_dev *priv)
 	 * operation, and the other is for std, fast mode, fast mode
 	 * plus operation. Currently we do not supprt high speed mode
 	 * so set brcr1 to 0.
+	 *
+	 * BRCR is a clock divider amount. Pick highest value that
+	 * leads to rate strictly below target.
 	 */
 	brcr1 = FIELD_PREP(I2C_BRCR_BRCNT1, 0);
-	brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2, i2c_clk / (priv->clk_freq * div));
+	brcr2 = FIELD_PREP(I2C_BRCR_BRCNT2, i2c_clk / (priv->clk_freq * div) + 1);
 
 	/* set the baud rate counter register */
 	writel((brcr1 | brcr2), priv->virtbase + I2C_BRCR);

-- 
2.46.2