| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <hdgh3mto5b2alygxxxv55km4yucjdnldd3zxxecqwm552ltk2q@z7tea4374gi2>
Date: Mon, 14 Oct 2024 02:58:32 +0300
From: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
To: Liu Ying <victor.liu@....com>
Cc: dri-devel@...ts.freedesktop.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, imx@...ts.linux.dev, linux-arm-kernel@...ts.infradead.org,
andrzej.hajda@...el.com, neil.armstrong@...aro.org, rfoss@...nel.org,
Laurent.pinchart@...asonboard.com, jonas@...boo.se, jernej.skrabec@...il.com, airlied@...il.com,
simona@...ll.ch, maarten.lankhorst@...ux.intel.com, mripard@...nel.org,
tzimmermann@...e.de, robh@...nel.org, krzk+dt@...nel.org, conor+dt@...nel.org,
shawnguo@...nel.org, s.hauer@...gutronix.de, kernel@...gutronix.de,
festevam@...il.com, catalin.marinas@....com, will@...nel.org,
quic_bjorande@...cinc.com, geert+renesas@...der.be, arnd@...db.de, nfraprado@...labora.com,
o.rempel@...gutronix.de, y.moog@...tec.de, marex@...x.de, isaac.scott@...asonboard.com,
biju.das.jz@...renesas.com
Subject: Re: [PATCH v2 6/9] drm/bridge: Add ITE IT6263 LVDS to HDMI converter
On Sat, Oct 12, 2024 at 06:01:30PM +0800, Liu Ying wrote:
> On 10/12/2024, Dmitry Baryshkov wrote:
> > On Sat, Oct 12, 2024 at 03:35:40PM +0800, Liu Ying wrote:
> >> Add basic HDMI video output support. Currently, only RGB888 output
> >> pixel format is supported. At the LVDS input side, the driver
> >> supports single LVDS link and dual LVDS links with "jeida-24" LVDS
> >> mapping.
> >>
> >> Product link:
> >> https://www.ite.com.tw/en/product/cate1/IT6263
> >>
> >> Signed-off-by: Liu Ying <victor.liu@....com>
> >> ---
> >> v2:
> >> * Add AVI inforframe support. (Maxime)
> >
> > Maxime asked to wire up the HDMI Connector framework. I have pushed the
> > patch that converts lt9611.c driver. Please implement similar changes in
> > your driver.
>
> Hmm, didn't fully get the meaning of "the new HDMI bridge infrastructure"
> maxime asked. Ok, will take a look at lt9611.c.
>
> >
> >> * Add DRM_MODE_CONNECTOR_HDMIA. (Biju)
> >> * Rename it6263_reset() to it6263_hw_reset(). (Biju)
> >> * Check number of LVDS link data lanes. (Biju)
> >>
> >> drivers/gpu/drm/bridge/Kconfig | 8 +
> >> drivers/gpu/drm/bridge/Makefile | 1 +
> >> drivers/gpu/drm/bridge/ite-it6263.c | 919 ++++++++++++++++++++++++++++
> >> 3 files changed, 928 insertions(+)
> >> create mode 100644 drivers/gpu/drm/bridge/ite-it6263.c
> >>
> >> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> >> index 3eb955333c80..93f99682a090 100644
> >> --- a/drivers/gpu/drm/bridge/Kconfig
> >> +++ b/drivers/gpu/drm/bridge/Kconfig
> >> @@ -90,6 +90,14 @@ config DRM_FSL_LDB
> >> help
> >> Support for i.MX8MP DPI-to-LVDS on-SoC encoder.
> >>
> >> +config DRM_ITE_IT6263
> >> + tristate "ITE IT6263 LVDS/HDMI bridge"
> >> + depends on OF
> >> + select DRM_KMS_HELPER
> >> + select REGMAP_I2C
> >> + help
> >> + ITE IT6263 LVDS to HDMI bridge chip driver.
> >> +
> >> config DRM_ITE_IT6505
> >> tristate "ITE IT6505 DisplayPort bridge"
> >> depends on OF
> >> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> >> index 7df87b582dca..f3776dd473fd 100644
> >> --- a/drivers/gpu/drm/bridge/Makefile
> >> +++ b/drivers/gpu/drm/bridge/Makefile
> >> @@ -6,6 +6,7 @@ obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
> >> obj-$(CONFIG_DRM_CROS_EC_ANX7688) += cros-ec-anx7688.o
> >> obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
> >> obj-$(CONFIG_DRM_FSL_LDB) += fsl-ldb.o
> >> +obj-$(CONFIG_DRM_ITE_IT6263) += ite-it6263.o
> >> obj-$(CONFIG_DRM_ITE_IT6505) += ite-it6505.o
> >> obj-$(CONFIG_DRM_LONTIUM_LT8912B) += lontium-lt8912b.o
> >> obj-$(CONFIG_DRM_LONTIUM_LT9211) += lontium-lt9211.o
> >> diff --git a/drivers/gpu/drm/bridge/ite-it6263.c b/drivers/gpu/drm/bridge/ite-it6263.c
> >> new file mode 100644
> >> index 000000000000..9b3318792f15
> >> --- /dev/null
> >> +++ b/drivers/gpu/drm/bridge/ite-it6263.c
> >> @@ -0,0 +1,919 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Copyright 2024 NXP
> >> + */
> >> +
> >> +#include <linux/bitfield.h>
> >> +#include <linux/bits.h>
> >> +#include <linux/delay.h>
> >> +#include <linux/gpio/consumer.h>
> >> +#include <linux/hdmi.h>
> >> +#include <linux/i2c.h>
> >> +#include <linux/media-bus-format.h>
> >> +#include <linux/module.h>
> >> +#include <linux/of.h>
> >> +#include <linux/regmap.h>
> >> +#include <linux/regulator/consumer.h>
> >> +
> >> +#include <drm/drm_atomic.h>
> >> +#include <drm/drm_atomic_helper.h>
> >> +#include <drm/drm_atomic_state_helper.h>
> >> +#include <drm/drm_bridge.h>
> >> +#include <drm/drm_connector.h>
> >> +#include <drm/drm_crtc.h>
> >> +#include <drm/drm_edid.h>
> >> +#include <drm/drm_of.h>
> >> +#include <drm/drm_probe_helper.h>
> >> +
> >> +/* -----------------------------------------------------------------------------
> >> + * LVDS registers
> >> + */
> >> +
> >> +/* LVDS software reset registers */
> >> +#define LVDS_REG_05 0x05
> >> +#define REG_SOFT_P_RST BIT(1)
> >> +
> >> +/* LVDS system configuration registers */
> >> +/* 0x0b */
> >> +#define LVDS_REG_0B 0x0b
> >> +#define REG_SSC_PCLK_RF BIT(0)
> >> +#define REG_LVDS_IN_SWAP BIT(1)
> >> +
> >> +/* LVDS test pattern gen control registers */
> >> +/* 0x2c */
> >> +#define LVDS_REG_2C 0x2c
> >> +#define REG_COL_DEP GENMASK(1, 0)
> >> +#define BIT8 FIELD_PREP(REG_COL_DEP, 2)
> >> +#define OUT_MAP BIT(4)
> >> +#define JEIDA 0
> >> +#define REG_DESSC_ENB BIT(6)
> >> +#define DMODE BIT(7)
> >> +#define DISO BIT(7)
> >> +#define SISO 0
> >> +
> >> +#define LVDS_REG_3C 0x3c
> >> +#define LVDS_REG_3F 0x3f
> >> +#define LVDS_REG_47 0x47
> >> +#define LVDS_REG_48 0x48
> >> +#define LVDS_REG_4F 0x4f
> >> +#define LVDS_REG_52 0x52
> >> +
> >> +/* -----------------------------------------------------------------------------
> >> + * HDMI registers are separated into three banks:
> >> + * 1) HDMI register common bank: 0x00 ~ 0x2f
> >> + */
> >> +
> >> +/* HDMI genernal registers */
> >> +#define HDMI_REG_SW_RST 0x04
> >> +#define SOFTREF_RST BIT(5)
> >> +#define SOFTA_RST BIT(4)
> >> +#define SOFTV_RST BIT(3)
> >> +#define AUD_RST BIT(2)
> >> +#define HDCP_RST BIT(0)
> >> +#define HDMI_RST_ALL (SOFTREF_RST | SOFTA_RST | SOFTV_RST | \
> >> + AUD_RST | HDCP_RST)
> >> +
> >> +#define HDMI_REG_SYS_STATUS 0x0e
> >> +#define HPDETECT BIT(6)
> >> +#define TXVIDSTABLE BIT(4)
> >> +
> >> +#define HDMI_REG_BANK_CTRL 0x0f
> >> +#define REG_BANK_SEL BIT(0)
> >> +
> >> +/* HDMI System DDC control registers */
> >> +#define HDMI_REG_DDC_MASTER_CTRL 0x10
> >> +#define MASTER_SEL_HOST BIT(0)
> >> +
> >> +#define HDMI_REG_DDC_HEADER 0x11
> >> +
> >> +#define HDMI_REG_DDC_REQOFF 0x12
> >> +#define HDMI_REG_DDC_REQCOUNT 0x13
> >> +#define HDMI_REG_DDC_EDIDSEG 0x14
> >> +
> >> +#define HDMI_REG_DDC_CMD 0x15
> >> +#define DDC_CMD_EDID_READ 0x3
> >> +#define DDC_CMD_FIFO_CLR 0x9
> >> +
> >> +#define HDMI_REG_DDC_STATUS 0x16
> >> +#define DDC_DONE BIT(7)
> >> +#define DDC_NOACK BIT(5)
> >> +#define DDC_WAITBUS BIT(4)
> >> +#define DDC_ARBILOSE BIT(3)
> >> +#define DDC_ERROR (DDC_NOACK | DDC_WAITBUS | DDC_ARBILOSE)
> >> +
> >> +#define HDMI_DDC_FIFO_BYTES 32
> >> +#define HDMI_REG_DDC_READFIFO 0x17
> >> +#define HDMI_REG_LVDS_PORT 0x1d /* LVDS input control I2C addr */
> >> +#define HDMI_REG_LVDS_PORT_EN 0x1e
> >> +#define LVDS_INPUT_CTRL_I2C_ADDR 0x33
> >> +
> >> +/* -----------------------------------------------------------------------------
> >> + * 2) HDMI register bank0: 0x30 ~ 0xff
> >> + */
> >> +
> >> +/* HDMI AFE registers */
> >> +#define HDMI_REG_AFE_DRV_CTRL 0x61
> >> +#define AFE_DRV_PWD BIT(5)
> >> +#define AFE_DRV_RST BIT(4)
> >> +
> >> +#define HDMI_REG_AFE_XP_CTRL 0x62
> >> +#define AFE_XP_GAINBIT BIT(7)
> >> +#define AFE_XP_ER0 BIT(4)
> >> +#define AFE_XP_RESETB BIT(3)
> >> +
> >> +#define HDMI_REG_AFE_ISW_CTRL 0x63
> >> +
> >> +#define HDMI_REG_AFE_IP_CTRL 0x64
> >> +#define AFE_IP_GAINBIT BIT(7)
> >> +#define AFE_IP_ER0 BIT(3)
> >> +#define AFE_IP_RESETB BIT(2)
> >> +
> >> +/* HDMI input data format registers */
> >> +#define HDMI_REG_INPUT_MODE 0x70
> >> +#define IN_RGB 0x00
> >> +
> >> +/* HDMI general control registers */
> >> +#define HDMI_REG_HDMI_MODE 0xc0
> >> +#define TX_HDMI_MODE BIT(0)
> >> +
> >> +#define HDMI_REG_GCP 0xc1
> >> +#define AVMUTE BIT(0)
> >> +#define HDMI_COLOR_DEPTH GENMASK(6, 4)
> >> +#define HDMI_COLOR_DEPTH_24 FIELD_PREP(HDMI_COLOR_DEPTH, 4)
> >> +
> >> +#define HDMI_REG_PKT_GENERAL_CTRL 0xc6
> >> +#define ENABLE_PKT BIT(0)
> >> +#define REPEAT_PKT BIT(1)
> >> +
> >> +/* -----------------------------------------------------------------------------
> >> + * 3) HDMI register bank1: 0x130 ~ 0x1ff (HDMI packet registers)
> >> + */
> >> +
> >> +/* AVI packet registers */
> >> +#define HDMI_REG_AVI_DB1 0x158
> >> +#define HDMI_REG_AVI_DB2 0x159
> >> +#define HDMI_REG_AVI_DB3 0x15a
> >> +#define HDMI_REG_AVI_DB4 0x15b
> >> +#define HDMI_REG_AVI_DB5 0x15c
> >> +#define HDMI_REG_AVI_CSUM 0x15d
> >> +#define HDMI_REG_AVI_DB6 0x15e
> >> +#define HDMI_REG_AVI_DB7 0x15f
> >> +#define HDMI_REG_AVI_DB8 0x160
> >> +#define HDMI_REG_AVI_DB9 0x161
> >> +#define HDMI_REG_AVI_DB10 0x162
> >> +#define HDMI_REG_AVI_DB11 0x163
> >> +#define HDMI_REG_AVI_DB12 0x164
> >> +#define HDMI_REG_AVI_DB13 0x165
> >> +
> >> +#define HDMI_AVI_DB_CHUNK1_SIZE (HDMI_REG_AVI_DB5 - HDMI_REG_AVI_DB1 + 1)
> >> +#define HDMI_AVI_DB_CHUNK2_SIZE (HDMI_REG_AVI_DB13 - HDMI_REG_AVI_DB6 + 1)
> >> +
> >> +#define MAX_PIXEL_CLOCK_KHZ 150000
> >> +#define HIGH_PIXEL_CLOCK_KHZ 80000
> >> +
> >> +struct it6263 {
> >> + struct device *dev;
> >> + struct i2c_client *hdmi_i2c;
> >> + struct i2c_client *lvds_i2c;
> >> + struct regmap *hdmi_regmap;
> >> + struct regmap *lvds_regmap;
> >> + struct drm_bridge bridge;
> >> + struct drm_bridge *next_bridge;
> >> + struct drm_connector connector;
> >> + struct gpio_desc *reset_gpio;
> >> + u8 lvds_link_num_dlanes;
> >> + bool lvds_dual_link;
> >> + bool lvds_link12_swap;
> >> +};
> >> +
> >> +static inline struct it6263 *bridge_to_it6263(struct drm_bridge *bridge)
> >> +{
> >> + return container_of(bridge, struct it6263, bridge);
> >> +}
> >> +
> >> +static inline struct it6263 *connector_to_it6263(struct drm_connector *conn)
> >> +{
> >> + return container_of(conn, struct it6263, connector);
> >> +}
> >> +
> >> +static bool it6263_hdmi_writeable_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + switch (reg) {
> >> + case HDMI_REG_SW_RST:
> >> + case HDMI_REG_BANK_CTRL:
> >> + case HDMI_REG_DDC_MASTER_CTRL:
> >> + case HDMI_REG_DDC_HEADER:
> >> + case HDMI_REG_DDC_REQOFF:
> >> + case HDMI_REG_DDC_REQCOUNT:
> >> + case HDMI_REG_DDC_EDIDSEG:
> >> + case HDMI_REG_DDC_CMD:
> >> + case HDMI_REG_LVDS_PORT:
> >> + case HDMI_REG_LVDS_PORT_EN:
> >> + case HDMI_REG_AFE_DRV_CTRL:
> >> + case HDMI_REG_AFE_XP_CTRL:
> >> + case HDMI_REG_AFE_ISW_CTRL:
> >> + case HDMI_REG_AFE_IP_CTRL:
> >> + case HDMI_REG_INPUT_MODE:
> >> + case HDMI_REG_HDMI_MODE:
> >> + case HDMI_REG_GCP:
> >> + case HDMI_REG_PKT_GENERAL_CTRL:
> >> + case HDMI_REG_AVI_DB1:
> >> + case HDMI_REG_AVI_DB2:
> >> + case HDMI_REG_AVI_DB3:
> >> + case HDMI_REG_AVI_DB4:
> >> + case HDMI_REG_AVI_DB5:
> >> + case HDMI_REG_AVI_CSUM:
> >> + case HDMI_REG_AVI_DB6:
> >> + case HDMI_REG_AVI_DB7:
> >> + case HDMI_REG_AVI_DB8:
> >> + case HDMI_REG_AVI_DB9:
> >> + case HDMI_REG_AVI_DB10:
> >> + case HDMI_REG_AVI_DB11:
> >> + case HDMI_REG_AVI_DB12:
> >> + case HDMI_REG_AVI_DB13:
> >> + return true;
> >> + default:
> >> + return false;
> >> + }
> >> +}
> >> +
> >> +static bool it6263_hdmi_readable_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + if (it6263_hdmi_writeable_reg(dev, reg))
> >> + return true;
> >> +
> >> + switch (reg) {
> >> + case HDMI_REG_SYS_STATUS:
> >> + case HDMI_REG_DDC_STATUS:
> >> + case HDMI_REG_DDC_READFIFO:
> >> + return true;
> >> + default:
> >> + return false;
> >> + }
> >> +}
> >> +
> >> +static bool it6263_hdmi_volatile_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + switch (reg) {
> >> + case HDMI_REG_SW_RST:
> >> + case HDMI_REG_SYS_STATUS:
> >> + case HDMI_REG_DDC_STATUS:
> >> + case HDMI_REG_DDC_READFIFO:
> >> + return true;
> >> + default:
> >> + return false;
> >> + }
> >> +}
> >> +
> >> +static const struct regmap_range_cfg it6263_hdmi_range_cfg = {
> >> + .range_min = 0x00,
> >> + .range_max = HDMI_REG_AVI_DB13,
> >> + .selector_reg = HDMI_REG_BANK_CTRL,
> >> + .selector_mask = REG_BANK_SEL,
> >> + .selector_shift = 0,
> >> + .window_start = 0x00,
> >> + .window_len = 0x100,
> >> +};
> >> +
> >> +static const struct regmap_config it6263_hdmi_regmap_config = {
> >> + .name = "it6263-hdmi",
> >> + .reg_bits = 8,
> >> + .val_bits = 8,
> >> + .writeable_reg = it6263_hdmi_writeable_reg,
> >> + .readable_reg = it6263_hdmi_readable_reg,
> >> + .volatile_reg = it6263_hdmi_volatile_reg,
> >> + .max_register = HDMI_REG_AVI_DB13,
> >> + .ranges = &it6263_hdmi_range_cfg,
> >> + .num_ranges = 1,
> >> + .cache_type = REGCACHE_MAPLE,
> >> +};
> >> +
> >> +static bool it6263_lvds_writeable_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + switch (reg) {
> >> + case LVDS_REG_05:
> >> + case LVDS_REG_0B:
> >> + case LVDS_REG_2C:
> >> + case LVDS_REG_3C:
> >> + case LVDS_REG_3F:
> >> + case LVDS_REG_47:
> >> + case LVDS_REG_48:
> >> + case LVDS_REG_4F:
> >> + case LVDS_REG_52:
> >> + return true;
> >> + default:
> >> + return false;
> >> + }
> >> +}
> >> +
> >> +static bool it6263_lvds_readable_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + return it6263_lvds_writeable_reg(dev, reg);
> >> +}
> >> +
> >> +static bool it6263_lvds_volatile_reg(struct device *dev, unsigned int reg)
> >> +{
> >> + return reg == LVDS_REG_05;
> >> +}
> >> +
> >> +static const struct regmap_config it6263_lvds_regmap_config = {
> >> + .name = "it6263-lvds",
> >> + .reg_bits = 8,
> >> + .val_bits = 8,
> >> + .writeable_reg = it6263_lvds_writeable_reg,
> >> + .readable_reg = it6263_lvds_readable_reg,
> >> + .volatile_reg = it6263_lvds_volatile_reg,
> >> + .max_register = LVDS_REG_52,
> >> + .cache_type = REGCACHE_MAPLE,
> >> +};
> >> +
> >> +static const char * const it6263_supplies[] = {
> >> + "ivdd", "ovdd", "txavcc18", "txavcc33", "pvcc1", "pvcc2",
> >> + "avcc", "anvdd", "apvdd"
> >> +};
> >> +
> >> +static int it6263_parse_dt(struct it6263 *it)
> >> +{
> >> + struct device *dev = it->dev;
> >> + struct device_node *port0, *port1;
> >> + int ret;
> >> +
> >> + ret = of_property_read_u8(dev->of_node, "ite,lvds-link-num-data-lanes",
> >> + &it->lvds_link_num_dlanes);
> >> + if (ret) {
> >> + dev_err(dev, "failed to get LVDS link number of data lanes: %d\n",
> >> + ret);
> >> + return ret;
> >> + }
> >> +
> >> + it->next_bridge = devm_drm_of_get_bridge(dev, dev->of_node, 2, 0);
> >> + if (IS_ERR(it->next_bridge))
> >> + return dev_err_probe(dev, PTR_ERR(it->next_bridge),
> >> + "failed to get next bridge\n");
> >> +
> >> + port0 = of_graph_get_port_by_id(dev->of_node, 0);
> >> + port1 = of_graph_get_port_by_id(dev->of_node, 1);
> >> + if (port0 && port1) {
> >> + if (of_property_read_bool(port0, "dual-lvds-even-pixels") &&
> >> + of_property_read_bool(port1, "dual-lvds-odd-pixels")) {
> >> + it->lvds_dual_link = true;
> >> + it->lvds_link12_swap = true;
> >
> > This is a nice name for the propery in the Dual Link LVDS case:
> >
> > ite,lvds-link-swap
>
> Swapping LVDS link1&2 is implied by the dual-lvds-{even,odd}-pixels
> properties that DT writers specify in port@0 and port@1.
>
> The DT writers don't need to use a dedicated property like
> ite,lvds-link-swap to explicitly indicate the swap.
Ack
>
> >
> >
> >> + } else if (of_property_read_bool(port0, "dual-lvds-odd-pixels") &&
> >> + of_property_read_bool(port1, "dual-lvds-even-pixels")) {
> >> + it->lvds_dual_link = true;
> >> + }
> >> +
> >> + if (!it->lvds_dual_link) {
> >> + dev_err(dev,
> >> + "failed to get LVDS dual link pixel order\n");
> >> + ret = -EINVAL;
> >> + }
> >> + } else if (port1) {
> >> + ret = -EINVAL;
> >> + dev_err(dev, "single input LVDS port1 is not supported\n");
> >> + } else if (!port0) {
> >> + ret = -EINVAL;
> >> + dev_err(dev, "no input LVDS port\n");
> >> + }
> >> +
> >> + of_node_put(port0);
> >> + of_node_put(port1);
> >> +
> >> + return ret;
> >> +}
> >> +
> >> +static inline void it6263_hw_reset(struct it6263 *it)
> >> +{
> >> + if (!it->reset_gpio)
> >> + return;
> >> +
> >> + gpiod_set_value_cansleep(it->reset_gpio, 0);
> >> + fsleep(1000);
> >> + gpiod_set_value_cansleep(it->reset_gpio, 1);
> >> + /* The chip maker says the low pulse should be at least 40ms. */
> >> + fsleep(40000);
> >> + gpiod_set_value_cansleep(it->reset_gpio, 0);
> >> + /* addtional time to wait the high voltage to be stable */
> >> + fsleep(5000);
> >> +}
> >> +
> >> +static inline int it6263_lvds_set_i2c_addr(struct it6263 *it)
> >> +{
> >> + int ret;
> >> +
> >> + ret = regmap_write(it->hdmi_regmap, HDMI_REG_LVDS_PORT,
> >> + LVDS_INPUT_CTRL_I2C_ADDR << 1);
> >> + if (ret)
> >> + return ret;
> >> +
> >> + return regmap_write(it->hdmi_regmap, HDMI_REG_LVDS_PORT_EN, BIT(0));
> >> +}
> >> +
> >> +static inline void it6263_lvds_reset(struct it6263 *it)
> >> +{
> >> + /* AFE PLL reset */
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_3C, BIT(0), 0x0);
> >> + fsleep(1000);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_3C, BIT(0), BIT(0));
> >> +
> >> + /* software pixel clock domain reset */
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_05, REG_SOFT_P_RST,
> >> + REG_SOFT_P_RST);
> >> + fsleep(1000);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_05, REG_SOFT_P_RST, 0x0);
> >> + fsleep(10000);
> >> +}
> >> +
> >> +static inline void it6263_lvds_set_interface(struct it6263 *it)
> >> +{
> >> + /* color depth */
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_2C, REG_COL_DEP, BIT8);
> >> + /* output mapping */
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_2C, OUT_MAP, JEIDA);
> >> +
> >> + if (it->lvds_dual_link) {
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_2C, DMODE, DISO);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_52, BIT(1), BIT(1));
> >> + } else {
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_2C, DMODE, SISO);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_52, BIT(1), 0);
> >> + }
> >> +}
> >> +
> >> +static inline void it6263_lvds_set_afe(struct it6263 *it)
> >> +{
> >> + regmap_write(it->lvds_regmap, LVDS_REG_3C, 0xaa);
> >> + regmap_write(it->lvds_regmap, LVDS_REG_3F, 0x02);
> >> + regmap_write(it->lvds_regmap, LVDS_REG_47, 0xaa);
> >> + regmap_write(it->lvds_regmap, LVDS_REG_48, 0x02);
> >> + regmap_write(it->lvds_regmap, LVDS_REG_4F, 0x11);
> >> +
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_0B, REG_SSC_PCLK_RF,
> >> + REG_SSC_PCLK_RF);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_3C, 0x07, 0);
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_2C, REG_DESSC_ENB,
> >> + REG_DESSC_ENB);
> >> +}
> >> +
> >> +static inline void it6263_lvds_sys_cfg(struct it6263 *it)
> >> +{
> >> + regmap_write_bits(it->lvds_regmap, LVDS_REG_0B, REG_LVDS_IN_SWAP,
> >> + it->lvds_link12_swap ? REG_LVDS_IN_SWAP : 0);
> >> +}
> >> +
> >> +static inline void it6263_lvds_config(struct it6263 *it)
> >> +{
> >> + it6263_lvds_reset(it);
> >> + it6263_lvds_set_interface(it);
> >> + it6263_lvds_set_afe(it);
> >> + it6263_lvds_sys_cfg(it);
> >> +}
> >> +
> >> +static inline void it6263_hdmi_config(struct it6263 *it)
> >> +{
> >> + regmap_write(it->hdmi_regmap, HDMI_REG_SW_RST, HDMI_RST_ALL);
> >> + regmap_write(it->hdmi_regmap, HDMI_REG_INPUT_MODE, IN_RGB);
> >> + regmap_write_bits(it->hdmi_regmap, HDMI_REG_GCP, HDMI_COLOR_DEPTH,
> >> + HDMI_COLOR_DEPTH_24);
> >> +}
> >> +
> >> +static enum drm_connector_status it6263_detect(struct it6263 *it)
> >> +{
> >> + unsigned int val;
> >> +
> >> + regmap_read(it->hdmi_regmap, HDMI_REG_SYS_STATUS, &val);
> >> + if (val & HPDETECT)
> >> + return connector_status_connected;
> >> + else
> >> + return connector_status_disconnected;
> >> +}
> >> +
> >> +static enum drm_connector_status
> >> +it6263_connector_detect(struct drm_connector *connector, bool force)
> >> +{
> >> + struct it6263 *it = connector_to_it6263(connector);
> >> +
> >> + return it6263_detect(it);
> >> +}
> >> +
> >> +static const struct drm_connector_funcs it6263_connector_funcs = {
> >> + .detect = it6263_connector_detect,
> >> + .fill_modes = drm_helper_probe_single_connector_modes,
> >> + .destroy = drm_connector_cleanup,
> >> + .reset = drm_atomic_helper_connector_reset,
> >> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> >> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> >> +};
> >> +
> >> +static int it6263_read_edid(void *data, u8 *buf, unsigned int block, size_t len)
> >> +{
> >> + struct it6263 *it = data;
> >> + struct regmap *regmap = it->hdmi_regmap;
> >> + unsigned int start = (block % 2) * EDID_LENGTH;
> >> + unsigned int segment = block >> 1;
> >> + unsigned int count, val;
> >> + int ret;
> >> +
> >> + regmap_write(regmap, HDMI_REG_DDC_MASTER_CTRL, MASTER_SEL_HOST);
> >> + regmap_write(regmap, HDMI_REG_DDC_HEADER, DDC_ADDR << 1);
> >> + regmap_write(regmap, HDMI_REG_DDC_EDIDSEG, segment);
> >> +
> >> + while (len) {
> >> + /* clear DDC FIFO */
> >> + regmap_write(regmap, HDMI_REG_DDC_CMD, DDC_CMD_FIFO_CLR);
> >> +
> >> + ret = regmap_read_poll_timeout(regmap, HDMI_REG_DDC_STATUS,
> >> + val, val & DDC_DONE,
> >> + 2000, 10000);
> >> + if (ret) {
> >> + dev_err(it->dev, "failed to clear DDC FIFO:%d\n", ret);
> >> + return ret;
> >> + }
> >> +
> >> + count = len > HDMI_DDC_FIFO_BYTES ? HDMI_DDC_FIFO_BYTES : len;
> >> +
> >> + /* fire the read command */
> >> + regmap_write(regmap, HDMI_REG_DDC_REQOFF, start);
> >> + regmap_write(regmap, HDMI_REG_DDC_REQCOUNT, count);
> >> + regmap_write(regmap, HDMI_REG_DDC_CMD, DDC_CMD_EDID_READ);
> >> +
> >> + start += count;
> >> + len -= count;
> >> +
> >> + ret = regmap_read_poll_timeout(regmap, HDMI_REG_DDC_STATUS, val,
> >> + val & (DDC_DONE | DDC_ERROR),
> >> + 20000, 250000);
> >> + if (ret && !(val & DDC_ERROR)) {
> >> + dev_err(it->dev, "failed to read EDID:%d\n", ret);
> >> + return ret;
> >> + }
> >> +
> >> + if (val & DDC_ERROR) {
> >> + dev_err(it->dev, "DDC error\n");
> >> + return -EIO;
> >> + }
> >> +
> >> + /* cache to buffer */
> >> + for (; count > 0; count--) {
> >> + regmap_read(regmap, HDMI_REG_DDC_READFIFO, &val);
> >> + *(buf++) = val;
> >> + }
> >> + }
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int it6263_connector_get_modes(struct drm_connector *connector)
> >> +{
> >> + struct it6263 *it = connector_to_it6263(connector);
> >> + const struct drm_edid *drm_edid;
> >> + int count;
> >> +
> >> + drm_edid = drm_edid_read_custom(connector, it6263_read_edid, it);
> >> +
> >> + drm_edid_connector_update(connector, drm_edid);
> >> + count = drm_edid_connector_add_modes(connector);
> >> +
> >> + drm_edid_free(drm_edid);
> >> +
> >> + return count;
> >> +}
> >> +
> >> +static const struct drm_connector_helper_funcs it6263_connector_helper_funcs = {
> >> + .get_modes = it6263_connector_get_modes,
> >> +};
> >> +
> >> +static int it6263_bridge_atomic_check(struct drm_bridge *bridge,
> >> + struct drm_bridge_state *bridge_state,
> >> + struct drm_crtc_state *crtc_state,
> >> + struct drm_connector_state *conn_state)
> >> +{
> >> + struct drm_display_mode *mode = &crtc_state->adjusted_mode;
> >
> > Use drm_atomic_helper_connector_hdmi_check().
>
> Will take a look at this.
>
> >
> > Implement .hdmi_tmds_char_rate_valid(). Also, I think, single and dual
>
> Will take a look at this.
>
> > link LVDS have different max clock rates. Please correct me if I'm
> > wrong.
>
> Yes, I think so too. But, I don't know the exact max clock rates.
> IT6263 data sheet only says LVDS RX supports clock rate up to
> 150MHz.
Is this the mode clock or the LVDS link clock rate?
>
> >
> >> +
> >> + return mode->clock > MAX_PIXEL_CLOCK_KHZ ? -EINVAL : 0;
> >> +}
> >> +
> >> +static void
> >> +it6263_bridge_atomic_disable(struct drm_bridge *bridge,
> >> + struct drm_bridge_state *old_bridge_state)
> >> +{
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> +
> >> + regmap_write_bits(it->hdmi_regmap, HDMI_REG_GCP, AVMUTE, AVMUTE);
> >> + regmap_write(it->hdmi_regmap, HDMI_REG_PKT_GENERAL_CTRL, 0);
> >> + regmap_write(it->hdmi_regmap, HDMI_REG_AFE_DRV_CTRL,
> >> + AFE_DRV_RST | AFE_DRV_PWD);
> >> +}
> >> +
> >> +static void
> >> +it6263_hdmi_avi_infoframe_configure(struct it6263 *it,
> >> + struct drm_connector *connector,
> >> + const struct drm_display_mode *mode)
> >
> > -> .hdmi_write_infoframe() , .hdmi_clear_infoframe().
>
>
> Will take a look at them.
>
> >
> >> +{
> >> + struct hdmi_avi_infoframe frame;
> >> + u8 buf[HDMI_INFOFRAME_SIZE(AVI)];
> >> + int ret;
> >> +
> >> + ret = drm_hdmi_avi_infoframe_from_display_mode(&frame, connector, mode);
> >> + if (ret) {
> >> + dev_err(it->dev, "failed to setup AVI infoframe: %d\n", ret);
> >> + return;
> >> + }
> >> +
> >> + ret = hdmi_avi_infoframe_pack(&frame, buf, sizeof(buf));
> >> + if (ret < 0) {
> >> + dev_err(it->dev, "failed to pack infoframe: %d\n", ret);
> >> + return;
> >> + }
> >> +
> >> + /* write the first AVI infoframe data byte chunk(DB1-DB5) */
> >> + ret = regmap_bulk_write(it->hdmi_regmap, HDMI_REG_AVI_DB1,
> >> + &buf[HDMI_INFOFRAME_HEADER_SIZE],
> >> + HDMI_AVI_DB_CHUNK1_SIZE);
> >> + if (ret) {
> >> + dev_err(it->dev, "failed to write the 1st AVI infoframe data byte chunk: %d\n",
> >> + ret);
> >> + return;
> >> + }
> >> +
> >> + /* write the second AVI infoframe data byte chunk(DB6-DB13) */
> >> + ret = regmap_bulk_write(it->hdmi_regmap, HDMI_REG_AVI_DB6,
> >> + &buf[HDMI_INFOFRAME_HEADER_SIZE +
> >> + HDMI_AVI_DB_CHUNK1_SIZE],
> >> + HDMI_AVI_DB_CHUNK2_SIZE);
> >> + if (ret) {
> >> + dev_err(it->dev, "failed to write the 2nd AVI infoframe data byte chunk: %d\n",
> >> + ret);
> >> + return;
> >> + }
> >> +
> >> + ret = regmap_write(it->hdmi_regmap, HDMI_REG_AVI_CSUM, buf[3]);
> >> + if (ret)
> >> + dev_err(it->dev, "failed to set AVI infoframe checksum: %d\n",
> >> + ret);
> >> +}
> >> +
> >> +static void
> >> +it6263_bridge_atomic_enable(struct drm_bridge *bridge,
> >> + struct drm_bridge_state *old_bridge_state)
> >> +{
> >> + struct drm_atomic_state *state = old_bridge_state->base.state;
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> + const struct drm_crtc_state *crtc_state;
> >> + struct regmap *regmap = it->hdmi_regmap;
> >> + const struct drm_display_mode *mode;
> >> + struct drm_connector *connector;
> >> + bool is_stable = false;
> >> + struct drm_crtc *crtc;
> >> + unsigned int val;
> >> + bool pclk_high;
> >> + int i, ret;
> >> +
> >> + connector = drm_atomic_get_new_connector_for_encoder(state,
> >> + bridge->encoder);
> >> + crtc = drm_atomic_get_new_connector_state(state, connector)->crtc;
> >> + crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
> >> + mode = &crtc_state->adjusted_mode;
> >> +
> >> + regmap_write(regmap, HDMI_REG_HDMI_MODE, TX_HDMI_MODE);
> >> +
> >> + it6263_hdmi_avi_infoframe_configure(it, connector, mode);
> >
> > drm_atomic_helper_connector_hdmi_update_infoframes
>
> Will take a look at this.
>
> >
> >> +
> >> + /* HDMI AFE setup */
> >> + pclk_high = mode->clock > HIGH_PIXEL_CLOCK_KHZ ? true : false;
> >> + regmap_write(regmap, HDMI_REG_AFE_DRV_CTRL, AFE_DRV_RST);
> >> + if (pclk_high)
> >> + regmap_write(regmap, HDMI_REG_AFE_XP_CTRL,
> >> + AFE_XP_GAINBIT | AFE_XP_RESETB);
> >> + else
> >> + regmap_write(regmap, HDMI_REG_AFE_XP_CTRL,
> >> + AFE_XP_ER0 | AFE_XP_RESETB);
> >> + regmap_write(regmap, HDMI_REG_AFE_ISW_CTRL, 0x10);
> >> + if (pclk_high)
> >> + regmap_write(regmap, HDMI_REG_AFE_IP_CTRL,
> >> + AFE_IP_GAINBIT | AFE_IP_RESETB);
> >> + else
> >> + regmap_write(regmap, HDMI_REG_AFE_IP_CTRL,
> >> + AFE_IP_ER0 | AFE_IP_RESETB);
> >> +
> >> + /* HDMI software video reset */
> >> + regmap_write_bits(regmap, HDMI_REG_SW_RST, SOFTV_RST, SOFTV_RST);
> >> + fsleep(1000);
> >> + regmap_write_bits(regmap, HDMI_REG_SW_RST, SOFTV_RST, 0);
> >> +
> >> + /* reconfigure LVDS and retry several times in case video is instable */
> >> + for (i = 0; i < 3; i++) {
> >> + ret = regmap_read_poll_timeout(regmap, HDMI_REG_SYS_STATUS, val,
> >> + val & TXVIDSTABLE,
> >> + 20000, 500000);
> >> + if (!ret) {
> >> + is_stable = true;
> >> + break;
> >> + }
> >> +
> >> + it6263_lvds_config(it);
> >> + }
> >> +
> >> + if (!is_stable)
> >> + dev_warn(it->dev, "failed to wait for video stable\n");
> >> +
> >> + /* HDMI AFE reset release and power up */
> >> + regmap_write(regmap, HDMI_REG_AFE_DRV_CTRL, 0);
> >> +
> >> + regmap_write_bits(regmap, HDMI_REG_GCP, AVMUTE, 0);
> >> +
> >> + regmap_write(regmap, HDMI_REG_PKT_GENERAL_CTRL, ENABLE_PKT | REPEAT_PKT);
> >> +}
> >> +
> >> +static enum drm_mode_status
> >> +it6263_bridge_mode_valid(struct drm_bridge *bridge,
> >> + const struct drm_display_info *info,
> >> + const struct drm_display_mode *mode)
> >> +{
> >> + return mode->clock > MAX_PIXEL_CLOCK_KHZ ? MODE_CLOCK_HIGH : MODE_OK;
> >
> > rate = drm_hdmi_compute_mode_clock(mode, 8, HDMI_COLORSPACE_RGB);
> > return bridge->funcs->hdmi_tmds_char_rate_valid(bridge, mode, rate);
>
> Will look into the two lines.
>
> >
> >> +}
> >> +
> >> +static int it6263_bridge_attach(struct drm_bridge *bridge,
> >> + enum drm_bridge_attach_flags flags)
> >> +{
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> + int ret;
> >> +
> >> + ret = drm_bridge_attach(bridge->encoder, it->next_bridge, bridge,
> >> + flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR);
> >> + if (ret < 0)
> >> + return ret;
> >> +
> >> + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
> >> + return 0;
> >> +
> >> + it->connector.polled = DRM_CONNECTOR_POLL_CONNECT |
> >> + DRM_CONNECTOR_POLL_DISCONNECT;
> >> +
> >
> > Please strongly consider dropping this and using drm_bridge_connector in
> > the host driver.
>
> I can't afford to make i.MX8MP imx-lcdif KMS use drm_bridge_connector
> currently. Maybe the Renesas RZ/G3E SMARC EVK Biju tested v1 patch
> set with is also not using drm_bridge_connector. I hope we can leave
> it as-is for now.
At least you can use drm_bridge_connector in this driver rather than
open-coding yet another connector implementation wich doesn't work with
the next bridges.
>
> >
> >> + ret = drm_connector_init(bridge->dev, &it->connector,
> >> + &it6263_connector_funcs,
> >> + DRM_MODE_CONNECTOR_HDMIA);
> >> + if (ret)
> >> + return ret;
> >> +
> >> + drm_connector_helper_add(&it->connector,
> >> + &it6263_connector_helper_funcs);
> >> + drm_connector_attach_encoder(&it->connector, bridge->encoder);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static enum drm_connector_status it6263_bridge_detect(struct drm_bridge *bridge)
> >> +{
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> +
> >> + return it6263_detect(it);
> >> +}
> >> +
> >> +static const struct drm_edid *
> >> +it6263_bridge_edid_read(struct drm_bridge *bridge,
> >> + struct drm_connector *connector)
> >> +{
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> +
> >> + return drm_edid_read_custom(connector, it6263_read_edid, it);
> >> +}
> >> +
> >> +static u32 *
> >> +it6263_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
> >> + struct drm_bridge_state *bridge_state,
> >> + struct drm_crtc_state *crtc_state,
> >> + struct drm_connector_state *conn_state,
> >> + u32 output_fmt,
> >> + unsigned int *num_input_fmts)
> >> +{
> >> + struct it6263 *it = bridge_to_it6263(bridge);
> >> + u32 *input_fmts;
> >> +
> >> + *num_input_fmts = 0;
> >> +
> >> + if (it->lvds_link_num_dlanes == 3)
> >> + return NULL;
> >> +
> >> + input_fmts = kmalloc(sizeof(*input_fmts), GFP_KERNEL);
> >> + if (!input_fmts)
> >> + return NULL;
> >> +
> >> + input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA;
> >> + *num_input_fmts = 1;
> >> +
> >> + return input_fmts;
> >> +}
> >> +
> >> +static const struct drm_bridge_funcs it6263_bridge_funcs = {
> >> + .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
> >> + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> >> + .atomic_reset = drm_atomic_helper_bridge_reset,
> >> + .attach = it6263_bridge_attach,
> >> + .mode_valid = it6263_bridge_mode_valid,
> >> + .atomic_disable = it6263_bridge_atomic_disable,
> >> + .atomic_enable = it6263_bridge_atomic_enable,
> >> + .atomic_check = it6263_bridge_atomic_check,
> >> + .detect = it6263_bridge_detect,
> >> + .edid_read = it6263_bridge_edid_read,
> >> + .atomic_get_input_bus_fmts = it6263_bridge_atomic_get_input_bus_fmts,
> >> +};
> >> +
> >> +static int it6263_probe(struct i2c_client *client)
> >> +{
> >> + struct device *dev = &client->dev;
> >> + struct it6263 *it;
> >> + int ret;
> >> +
> >> + it = devm_kzalloc(dev, sizeof(*it), GFP_KERNEL);
> >> + if (!it)
> >> + return -ENOMEM;
> >> +
> >> + it->dev = dev;
> >> + it->hdmi_i2c = client;
> >> +
> >> + it->hdmi_regmap = devm_regmap_init_i2c(client,
> >> + &it6263_hdmi_regmap_config);
> >> + if (IS_ERR(it->hdmi_regmap))
> >> + return dev_err_probe(dev, PTR_ERR(it->hdmi_regmap),
> >> + "failed to init I2C regmap for HDMI\n");
> >> +
> >> + it->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> >> + if (IS_ERR(it->reset_gpio))
> >> + return dev_err_probe(dev, PTR_ERR(it->reset_gpio),
> >> + "failed to get reset gpio\n");
> >> +
> >> + ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it6263_supplies),
> >> + it6263_supplies);
> >> + if (ret)
> >> + return dev_err_probe(dev, ret, "failed to get power supplies\n");
> >> +
> >> + ret = it6263_parse_dt(it);
> >> + if (ret)
> >> + return ret;
> >> +
> >> + it6263_hw_reset(it);
> >> +
> >> + ret = it6263_lvds_set_i2c_addr(it);
> >> + if (ret)
> >> + return dev_err_probe(dev, ret, "failed to set I2C addr\n");
> >> +
> >> + it->lvds_i2c = devm_i2c_new_dummy_device(dev, client->adapter,
> >> + LVDS_INPUT_CTRL_I2C_ADDR);
> >> + if (IS_ERR(it->lvds_i2c))
> >> + dev_err_probe(it->dev, PTR_ERR(it->lvds_i2c),
> >> + "failed to allocate I2C device for LVDS\n");
> >> +
> >> + it->lvds_regmap = devm_regmap_init_i2c(it->lvds_i2c,
> >> + &it6263_lvds_regmap_config);
> >> + if (IS_ERR(it->lvds_regmap))
> >> + return dev_err_probe(dev, PTR_ERR(it->lvds_regmap),
> >> + "failed to init I2C regmap for LVDS\n");
> >> +
> >> + it6263_lvds_config(it);
> >> + it6263_hdmi_config(it);
> >> +
> >> + i2c_set_clientdata(client, it);
> >> +
> >> + it->bridge.funcs = &it6263_bridge_funcs;
> >> + it->bridge.of_node = dev->of_node;
> >> + it->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_DETECT;
> >
> > | DRM_BRIDGE_OP_HDMI
>
> Will take a look at this.
>
> >
> > BTW: No HPD IRQ support?
> IT6263 chip doesn't support HPD IRQ.
ack
>
> >
> >> + it->bridge.type = DRM_MODE_CONNECTOR_HDMIA;
> >> + drm_bridge_add(&it->bridge);
> >
> > devm_drm_bridge_add()
>
> Will try to use this. Thanks.
>
> >
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static void it6263_remove(struct i2c_client *client)
> >> +{
> >> + struct it6263 *it = i2c_get_clientdata(client);
> >> +
> >> + drm_bridge_remove(&it->bridge);
> >
> > Remove, it becomes unused with the devm_ function.
> >
> >> +}
> >> +
> >> +static const struct of_device_id it6263_of_match[] = {
> >> + { .compatible = "ite,it6263", },
> >> + { }
> >> +};
> >> +MODULE_DEVICE_TABLE(of, it6263_of_match);
> >> +
> >> +static const struct i2c_device_id it6263_i2c_ids[] = {
> >> + { "it6263", 0 },
> >> + { }
> >> +};
> >> +MODULE_DEVICE_TABLE(i2c, it6263_i2c_ids);
> >> +
> >> +static struct i2c_driver it6263_driver = {
> >> + .probe = it6263_probe,
> >> + .remove = it6263_remove,
> >> + .driver = {
> >> + .name = "it6263",
> >> + .of_match_table = it6263_of_match,
> >> + },
> >> + .id_table = it6263_i2c_ids,
> >> +};
> >> +module_i2c_driver(it6263_driver);
> >> +
> >> +MODULE_DESCRIPTION("ITE Tech. Inc. IT6263 LVDS/HDMI bridge");
> >> +MODULE_AUTHOR("Liu Ying <victor.liu@....com>");
> >> +MODULE_LICENSE("GPL");
> >> --
> >> 2.34.1
> >>
> >
>
> --
> Regards,
> Liu Ying
>
--
With best wishes
Dmitry
Powered by blists - more mailing lists