lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <8443837.T7Z3S40VBb@steina-w>
Date: Thu, 24 Oct 2024 16:05:43 +0200
From: Alexander Stein <alexander.stein@...tq-group.com>
To: Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley <conor+dt@...nel.org>, Shawn Guo <shawnguo@...nel.org>, Sascha Hauer <s.hauer@...gutronix.de>, Pengutronix Kernel Team <kernel@...gutronix.de>, Fabio Estevam <festevam@...il.com>, "open list:TQ SYSTEMS BOARD & DRIVER SUPPORT" <linux@...tq-group.com>, "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" <devicetree@...r.kernel.org>, "open list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE" <imx@...ts.linux.dev>, "moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE" <linux-arm-kernel@...ts.infradead.org>, open list <linux-kernel@...r.kernel.org>, Frank Li <Frank.Li@....com>
Subject: Re: [PATCH 1/1] arm64: dts: imx8mn-tqma8mqnl-mba8mx-usbot: fix coexistence of output-low and output-high in GPIO

Hi Frank,

thanks for noticing the issue and also providing a patch.

Am Mittwoch, 23. Oktober 2024, 23:03:13 CEST schrieb Frank Li:
> Fix the issue where both 'output-low' and 'output-high' exist under GPIO
> hog nodes  (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
> tree overlays. Since /delete-property/ is not supported in the overlays,
> setting 'output-low' results in both properties being present. The
> workaround is to disable these hogs and create new ones with 'output-low'
> as needed.
> 
> Fix below CHECK_DTBS warning:
> arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
>    {'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
>        is valid under each of {'required': ['output-low']}, {'required': ['output-high']
> 
> Fixes: 3f6fc30abebc ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
> Signed-off-by: Frank Li <Frank.Li@....com>

Thanks, this works as intended. If this overlay applied the USB OTG connector (X19) can be used.

Reviewed-by: Alexander Stein <alexander.stein@...tq-group.com>

> ---
> Alex:
> 	I have not hardware to run it. I check dtb output is correct.
> ---
>  .../imx8mn-tqma8mqnl-mba8mx-usbotg.dtso       | 29 +++++++++++++++++--
>  1 file changed, 27 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> index 96db07fc9bece..1f2a0fe70a0a2 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
> @@ -29,12 +29,37 @@ usb_dr_connector: endpoint {
>  	};
>  };
>  
> +/*
> + * rst_usb_hub_hog and sel_usb_hub_hog have property 'output-high',
> + * dt overlay don't support /delete-property/. Both 'output-low' and
> + * 'output-high' will be exist under hog nodes if overlay file set
> + * 'output-low'. Workaround is disable these hog and create new hog with
> + * 'output-low'.
> + */
> +
>  &rst_usb_hub_hog {
> -	output-low;
> +	status = "disabled";
> +};
> +
> +&expander0 {
> +	rst-usb-low-hub-hog {
> +		gpio-hog;
> +		gpios = <13 0>;
> +		output-low;
> +		line-name = "RST_USB_HUB#";
> +	};
>  };
>  
>  &sel_usb_hub_hog {
> -	output-low;
> +	status = "disabled";
> +};
> +
> +&gpio2 {
> +	sel-usb-low-hub-hog {
> +		gpio-hog;
> +		gpios = <1 GPIO_ACTIVE_HIGH>;
> +		output-low;
> +	};
>  };
>  
>  &usbotg1 {
> 


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/



Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ