[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <j3a76pyolo66bcqemeo4o3gwzfnftcfjc6grg3v33u7ipztwiq@donxxbveypjk>
Date: Tue, 29 Oct 2024 08:08:09 +0100
From: Krzysztof Kozlowski <krzk@...nel.org>
To: Francesco Dolcini <francesco@...cini.it>
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, Mathias Nyman <mathias.nyman@...el.com>,
Francesco Dolcini <francesco.dolcini@...adex.com>, Parth Pancholi <parth.pancholi@...adex.com>,
linux-usb@...r.kernel.org, devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v4 1/2] dt-bindings: usb: add TUSB73x0 PCIe
On Mon, Oct 28, 2024 at 11:54:12AM +0100, Francesco Dolcini wrote:
> From: Parth Pancholi <parth.pancholi@...adex.com>
>
> Add device tree bindings for TI's TUSB73x0 PCIe-to-USB 3.0 xHCI
> host controller. The controller supports software configuration
> through PCIe registers, such as controlling the PWRONx polarity
> via the USB control register (E0h).
>
> Datasheet: https://www.ti.com/lit/ds/symlink/tusb7320.pdf
> Signed-off-by: Parth Pancholi <parth.pancholi@...adex.com>
> Signed-off-by: Francesco Dolcini <francesco.dolcini@...adex.com>
> ---
> v4:
> - add $ref: usb-xhci.yaml
> - description: wrap to 80 columns, add that the two variants use the
> same device ID
> - revise the example, based on comment from Rob and taking
> marvell,prestera.yaml as an example (this binding was reviewed and
> amended by Rob in the past).
> v3: use lowercase hex in compatible
> v2: rename property to ti,tusb7320-pwron-active-high and change type to flag
> ---
> .../bindings/usb/ti,tusb73x0-pci.yaml | 55 +++++++++++++++++++
> 1 file changed, 55 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
>
> diff --git a/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> new file mode 100644
> index 000000000000..e98a2e0bfcbb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> @@ -0,0 +1,55 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/ti,tusb73x0-pci.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TUSB73x0 USB 3.0 xHCI Host Controller (PCIe)
> +
> +maintainers:
> + - Francesco Dolcini <francesco.dolcini@...adex.com>
> +
> +description:
> + TUSB73x0 USB 3.0 xHCI Host Controller via PCIe x1 Gen2 interface.
> + The TUSB7320 supports up to two downstream ports, the TUSB7340 supports up
> + to four downstream ports, both variants share the same PCI device ID.
> +
> +properties:
> + compatible:
> + const: pci104c,8241
> +
> + reg:
> + maxItems: 1
> +
> + ti,tusb7320-pwron-active-high:
Drop tusb7320. There is never device name in property name, because it
is redundant and makes it completely not-reusable.
> + $ref: /schemas/types.yaml#/definitions/flag
> + description:
> + Configure the polarity of the PWRONx# signals. When this is present, the
> + PWRONx# pins are active high and their internal pull-down resistors are
> + disabled. When this is absent, the PWRONx# pins are active low (default)
> + and their internal pull-down resistors are enabled.
Best regards,
Krzysztof
Powered by blists - more mailing lists