linux-kernel - [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-ID: <20241125165648.509162-1-nicolas.ferre@microchip.com>
Date: Mon, 25 Nov 2024 17:56:48 +0100
From: <nicolas.ferre@...rochip.com>
To: Claudiu Beznea <claudiu.beznea@...on.dev>, Alexandre Belloni
	<alexandre.belloni@...tlin.com>
CC: <linux-arm-kernel@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
	Cristian Birsan <cristian.birsan@...rochip.com>, Nicolas Ferre
	<nicolas.ferre@...rochip.com>
Subject: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

From: Nicolas Ferre <nicolas.ferre@...rochip.com>

Change how the Backup Unit Power is configured and force the
automatic/hardware mode.
This change eliminates the need for software management of the power
switch, ensuring it transitions to the backup power source before
entering low power modes.

This is done in the only locaton where this swich was configured. It's
usually done in the bootloader.

Previously, the loss of the VDDANA (or VDDIN33) power source was not
automatically compensated by an alternative power source. This resulted
in the loss of Backup Unit content, including Backup Self-refresh low
power mode information, OTP emulation configuration, and boot
configuration, for instance.

Signed-off-by: Nicolas Ferre <nicolas.ferre@...rochip.com>
---
 arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
 1 file changed, 20 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index b9b995f8a36e..05a1547642b6 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
 	return 0;
 }
 
-static void at91_pm_switch_ba_to_vbat(void)
+/**
+ * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
+ * to automatic/hardware mode.
+ *
+ * The Backup Unit Power Switch can be managed either by software or hardware.
+ * Enabling hardware mode allows the automatic transition of power between
+ * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
+ * availability of these power sources.
+ *
+ * If the Backup Unit Power Switch is already in automatic mode, no action is
+ * required. If it is in software-controlled mode, it is switched to automatic
+ * mode to enhance safety and eliminate the need for toggling between power
+ * sources.
+ */
+static void at91_pm_switch_ba_to_auto(void)
 {
 	unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
 	unsigned int val;
@@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
 
 	val = readl(soc_pm.data.sfrbu + offset);
 
-	/* Already on VBAT. */
-	if (!(val & soc_pm.sfrbu_regs.pswbu.state))
+	/* Already on auto/hardware. */
+	if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
 		return;
 
-	val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
-	val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
+	val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
+	val |= soc_pm.sfrbu_regs.pswbu.key;
 	writel(val, soc_pm.data.sfrbu + offset);
-
-	/* Wait for update. */
-	val = readl(soc_pm.data.sfrbu + offset);
-	while (val & soc_pm.sfrbu_regs.pswbu.state)
-		val = readl(soc_pm.data.sfrbu + offset);
 }
 
 static void at91_pm_suspend(suspend_state_t state)
 {
 	if (soc_pm.data.mode == AT91_PM_BACKUP) {
-		at91_pm_switch_ba_to_vbat();
+		at91_pm_switch_ba_to_auto();
 
 		cpu_suspend(0, at91_suspend_finish);
 
-- 
2.39.2