| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20241213-sparx5-lan969x-switch-driver-4-v4-8-d1a72c9c4714@microchip.com>
Date: Fri, 13 Dec 2024 14:41:07 +0100
From: Daniel Machon <daniel.machon@...rochip.com>
To: <UNGLinuxDriver@...rochip.com>, Andrew Lunn <andrew+netdev@...n.ch>,
"David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, "Lars
Povlsen" <lars.povlsen@...rochip.com>, Steen Hegelund
<Steen.Hegelund@...rochip.com>, Horatiu Vultur
<horatiu.vultur@...rochip.com>, Russell King <linux@...linux.org.uk>,
<jacob.e.keller@...el.com>, <robh@...nel.org>, <krzk+dt@...nel.org>,
<conor+dt@...nel.org>
CC: <devicetree@...r.kernel.org>, <netdev@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <linux-arm-kernel@...ts.infradead.org>,
<robert.marko@...tura.hr>
Subject: [PATCH net-next v4 8/9] net: lan969x: add RGMII implementation
The lan969x switch device includes two RGMII port interfaces (port 28
and 29) supporting data speeds of 1 Gbps, 100 Mbps and 10 Mbps. MAC
level delays are configurable through the HSIO_WRAP target, by choosing
a phase shift selector, corresponding to a certain time delay in nano
seconds.
Add new file: lan969x_rgmii.c that contains the implementation for
configuring the RGMII port devices. MAC level delays are configured
using the "{rx,tx}-internal-delay-ps" properties. These properties must
be specified independently of the phy-mode. If missing, or set to zero,
the MAC will not apply any delay.
Reviewed-by: Steen Hegelund <Steen.Hegelund@...rochip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@...rochip.com>
Signed-off-by: Daniel Machon <daniel.machon@...rochip.com>
---
drivers/net/ethernet/microchip/sparx5/Makefile | 3 +-
.../ethernet/microchip/sparx5/lan969x/lan969x.c | 1 +
.../ethernet/microchip/sparx5/lan969x/lan969x.h | 5 +
.../microchip/sparx5/lan969x/lan969x_rgmii.c | 224 +++++++++++++++++++++
.../net/ethernet/microchip/sparx5/sparx5_main.h | 2 +
.../net/ethernet/microchip/sparx5/sparx5_port.c | 6 +
6 files changed, 240 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/microchip/sparx5/Makefile b/drivers/net/ethernet/microchip/sparx5/Makefile
index 4bf2a885a9da..3f34e83246a0 100644
--- a/drivers/net/ethernet/microchip/sparx5/Makefile
+++ b/drivers/net/ethernet/microchip/sparx5/Makefile
@@ -20,7 +20,8 @@ sparx5-switch-$(CONFIG_LAN969X_SWITCH) += lan969x/lan969x_regs.o \
lan969x/lan969x.o \
lan969x/lan969x_calendar.o \
lan969x/lan969x_vcap_ag_api.o \
- lan969x/lan969x_vcap_impl.o
+ lan969x/lan969x_vcap_impl.o \
+ lan969x/lan969x_rgmii.o
# Provide include files
ccflags-y += -I$(srctree)/drivers/net/ethernet/microchip/vcap
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
index be49a99556fe..396f76b6eea5 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
@@ -340,6 +340,7 @@ static const struct sparx5_ops lan969x_ops = {
.set_port_mux = &lan969x_port_mux_set,
.ptp_irq_handler = &lan969x_ptp_irq_handler,
.dsm_calendar_calc = &lan969x_dsm_calendar_calc,
+ .port_config_rgmii = &lan969x_port_config_rgmii,
};
const struct sparx5_match_data lan969x_desc = {
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
index 4b91c47d6d21..9a7ddebecf1e 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
@@ -67,4 +67,9 @@ static inline bool lan969x_port_is_rgmii(int portno)
/* lan969x_calendar.c */
int lan969x_dsm_calendar_calc(struct sparx5 *sparx5, u32 taxi,
struct sparx5_calendar_data *data);
+
+/* lan969x_rgmii.c */
+int lan969x_port_config_rgmii(struct sparx5_port *port,
+ struct sparx5_port_config *conf);
+
#endif
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c
new file mode 100644
index 000000000000..4e422ca50828
--- /dev/null
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Microchip lan969x Switch driver
+ *
+ * Copyright (c) 2024 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include "lan969x.h"
+
+/* Tx clock selectors */
+#define LAN969X_RGMII_TX_CLK_SEL_125MHZ 1 /* 1000Mbps */
+#define LAN969X_RGMII_TX_CLK_SEL_25MHZ 2 /* 100Mbps */
+#define LAN969X_RGMII_TX_CLK_SEL_2M5MHZ 3 /* 10Mbps */
+
+/* Port speed selectors */
+#define LAN969X_RGMII_SPEED_SEL_10 0 /* Select 10Mbps speed */
+#define LAN969X_RGMII_SPEED_SEL_100 1 /* Select 100Mbps speed */
+#define LAN969X_RGMII_SPEED_SEL_1000 2 /* Select 1000Mbps speed */
+
+/* Clock delay selectors */
+#define LAN969X_RGMII_CLK_DELAY_SEL_1_0_NS 2 /* Phase shift 45deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_1_7_NS 3 /* Phase shift 77deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_2_0_NS 4 /* Phase shift 90deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS 5 /* Phase shift 112deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_3_0_NS 6 /* Phase shift 135deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_3_3_NS 7 /* Phase shift 147deg */
+
+#define LAN969X_RGMII_PORT_START_IDX 28 /* Index of the first RGMII port */
+#define LAN969X_RGMII_IFG_TX 4 /* TX Inter Frame Gap value */
+#define LAN969X_RGMII_IFG_RX1 5 /* RX1 Inter Frame Gap value */
+#define LAN969X_RGMII_IFG_RX2 1 /* RX2 Inter Frame Gap value */
+
+#define RGMII_PORT_IDX(port) ((port)->portno - LAN969X_RGMII_PORT_START_IDX)
+
+/* Get the tx clock selector based on the port speed. */
+static int lan969x_rgmii_get_clk_sel(int speed)
+{
+ return (speed == SPEED_10 ? LAN969X_RGMII_TX_CLK_SEL_2M5MHZ :
+ speed == SPEED_100 ? LAN969X_RGMII_TX_CLK_SEL_25MHZ :
+ LAN969X_RGMII_TX_CLK_SEL_125MHZ);
+}
+
+/* Get the port speed selector based on the port speed. */
+static int lan969x_rgmii_get_speed_sel(int speed)
+{
+ return (speed == SPEED_10 ? LAN969X_RGMII_SPEED_SEL_10 :
+ speed == SPEED_100 ? LAN969X_RGMII_SPEED_SEL_100 :
+ LAN969X_RGMII_SPEED_SEL_1000);
+}
+
+/* Get the clock delay selector based on the clock delay in picoseconds. */
+static int lan969x_rgmii_get_clk_delay_sel(struct sparx5_port *port,
+ u32 delay_ps, u32 *clk_delay_sel)
+{
+ switch (delay_ps) {
+ case 0:
+ /* Hardware default selector. */
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS;
+ break;
+ case 1000:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_1_0_NS;
+ break;
+ case 1700:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_1_7_NS;
+ break;
+ case 2000:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_0_NS;
+ break;
+ case 2500:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS;
+ break;
+ case 3000:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_3_0_NS;
+ break;
+ case 3300:
+ *clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_3_3_NS;
+ break;
+ default:
+ dev_err(port->sparx5->dev, "Invalid RGMII delay: %u", delay_ps);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/* Configure the RGMII tx clock frequency. */
+static void lan969x_rgmii_tx_clk_config(struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 clk_sel = lan969x_rgmii_get_clk_sel(conf->speed);
+ u32 idx = RGMII_PORT_IDX(port);
+
+ /* Take the RGMII clock domain out of reset and set tx clock
+ * frequency.
+ */
+ spx5_rmw(HSIO_WRAP_RGMII_CFG_TX_CLK_CFG_SET(clk_sel) |
+ HSIO_WRAP_RGMII_CFG_RGMII_TX_RST_SET(0) |
+ HSIO_WRAP_RGMII_CFG_RGMII_RX_RST_SET(0),
+ HSIO_WRAP_RGMII_CFG_TX_CLK_CFG |
+ HSIO_WRAP_RGMII_CFG_RGMII_TX_RST |
+ HSIO_WRAP_RGMII_CFG_RGMII_RX_RST,
+ port->sparx5, HSIO_WRAP_RGMII_CFG(idx));
+}
+
+/* Configure the RGMII port device. */
+static void lan969x_rgmii_port_device_config(struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 dtag, dotag, etype, speed_sel, idx = RGMII_PORT_IDX(port);
+
+ speed_sel = lan969x_rgmii_get_speed_sel(conf->speed);
+
+ etype = (port->vlan_type == SPX5_VLAN_PORT_TYPE_S_CUSTOM ?
+ port->custom_etype :
+ port->vlan_type == SPX5_VLAN_PORT_TYPE_C ?
+ ETH_P_8021Q : ETH_P_8021AD);
+
+ dtag = port->max_vlan_tags == SPX5_PORT_MAX_TAGS_TWO;
+ dotag = port->max_vlan_tags != SPX5_PORT_MAX_TAGS_NONE;
+
+ /* Enable the MAC. */
+ spx5_wr(DEVRGMII_MAC_ENA_CFG_RX_ENA_SET(1) |
+ DEVRGMII_MAC_ENA_CFG_TX_ENA_SET(1),
+ port->sparx5, DEVRGMII_MAC_ENA_CFG(idx));
+
+ /* Configure the Inter Frame Gap. */
+ spx5_wr(DEVRGMII_MAC_IFG_CFG_TX_IFG_SET(LAN969X_RGMII_IFG_TX) |
+ DEVRGMII_MAC_IFG_CFG_RX_IFG1_SET(LAN969X_RGMII_IFG_RX1) |
+ DEVRGMII_MAC_IFG_CFG_RX_IFG2_SET(LAN969X_RGMII_IFG_RX2),
+ port->sparx5, DEVRGMII_MAC_IFG_CFG(idx));
+
+ /* Configure port data rate. */
+ spx5_wr(DEVRGMII_DEV_RST_CTRL_SPEED_SEL_SET(speed_sel),
+ port->sparx5, DEVRGMII_DEV_RST_CTRL(idx));
+
+ /* Configure VLAN awareness. */
+ spx5_wr(DEVRGMII_MAC_TAGS_CFG_TAG_ID_SET(etype) |
+ DEVRGMII_MAC_TAGS_CFG_PB_ENA_SET(dtag) |
+ DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA_SET(dotag) |
+ DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_SET(dotag),
+ port->sparx5,
+ DEVRGMII_MAC_TAGS_CFG(idx));
+}
+
+/* Configure the RGMII delay lines in the MAC.
+ *
+ * We use the rx-internal-delay-ps" and "tx-internal-delay-ps" properties to
+ * configure the rx and tx delays for the MAC. If these properties are missing
+ * or set to zero, the MAC will not apply any delay.
+ *
+ * The PHY side delays are determined by the PHY mode
+ * (e.g. PHY_INTERFACE_MODE_RGMII_{ID, RXID, TXID}), and ignored by the MAC side
+ * entirely.
+ */
+static int lan969x_rgmii_delay_config(struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ u32 tx_clk_sel, rx_clk_sel, tx_delay_ps = 0, rx_delay_ps = 0;
+ u32 idx = RGMII_PORT_IDX(port);
+ int err;
+
+ of_property_read_u32(port->of_node, "rx-internal-delay-ps",
+ &rx_delay_ps);
+
+ of_property_read_u32(port->of_node, "tx-internal-delay-ps",
+ &tx_delay_ps);
+
+ err = lan969x_rgmii_get_clk_delay_sel(port, rx_delay_ps, &rx_clk_sel);
+ if (err)
+ return err;
+
+ err = lan969x_rgmii_get_clk_delay_sel(port, tx_delay_ps, &tx_clk_sel);
+ if (err)
+ return err;
+
+ /* Configure rx delay. */
+ spx5_rmw(HSIO_WRAP_DLL_CFG_DLL_RST_SET(0) |
+ HSIO_WRAP_DLL_CFG_DLL_ENA_SET(1) |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_SET(!!rx_delay_ps) |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_SET(rx_clk_sel),
+ HSIO_WRAP_DLL_CFG_DLL_RST |
+ HSIO_WRAP_DLL_CFG_DLL_ENA |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_ENA |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_SEL,
+ port->sparx5, HSIO_WRAP_DLL_CFG(idx, 0));
+
+ /* Configure tx delay. */
+ spx5_rmw(HSIO_WRAP_DLL_CFG_DLL_RST_SET(0) |
+ HSIO_WRAP_DLL_CFG_DLL_ENA_SET(1) |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_SET(!!tx_delay_ps) |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_SET(tx_clk_sel),
+ HSIO_WRAP_DLL_CFG_DLL_RST |
+ HSIO_WRAP_DLL_CFG_DLL_ENA |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_ENA |
+ HSIO_WRAP_DLL_CFG_DLL_CLK_SEL,
+ port->sparx5, HSIO_WRAP_DLL_CFG(idx, 1));
+
+ return 0;
+}
+
+/* Configure GPIO's to be used as RGMII interface. */
+static void lan969x_rgmii_gpio_config(struct sparx5_port *port)
+{
+ u32 idx = RGMII_PORT_IDX(port);
+
+ /* Enable the RGMII on the GPIOs. */
+ spx5_wr(HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG_SET(1), port->sparx5,
+ HSIO_WRAP_XMII_CFG(!idx));
+}
+
+int lan969x_port_config_rgmii(struct sparx5_port *port,
+ struct sparx5_port_config *conf)
+{
+ int err;
+
+ err = lan969x_rgmii_delay_config(port, conf);
+ if (err)
+ return err;
+
+ lan969x_rgmii_tx_clk_config(port, conf);
+ lan969x_rgmii_gpio_config(port);
+ lan969x_rgmii_port_device_config(port, conf);
+
+ return 0;
+}
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
index c58d7841638e..3ae760da17e2 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
@@ -324,6 +324,8 @@ struct sparx5_ops {
irqreturn_t (*ptp_irq_handler)(int irq, void *args);
int (*dsm_calendar_calc)(struct sparx5 *sparx5, u32 taxi,
struct sparx5_calendar_data *data);
+ int (*port_config_rgmii)(struct sparx5_port *port,
+ struct sparx5_port_config *conf);
};
struct sparx5_main_io_resource {
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index 86d6c9e9ec7c..04bc8fffaf96 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -1012,6 +1012,12 @@ int sparx5_port_config(struct sparx5 *sparx5,
if (err)
return err;
+ if (rgmii) {
+ err = ops->port_config_rgmii(port, conf);
+ if (err)
+ return err;
+ }
+
/* high speed device is already configured */
if (!rgmii && !high_speed_dev)
sparx5_port_config_low_set(sparx5, port, conf);
--
2.34.1
Powered by blists - more mailing lists