| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250107165433.115050-1-mitltlatltl@gmail.com>
Date: Wed, 8 Jan 2025 00:54:30 +0800
From: Pengyu Luo <mitltlatltl@...il.com>
To: heikki.krogerus@...ux.intel.com
Cc: andersson@...nel.org,
bryan.odonoghue@...aro.org,
conor+dt@...nel.org,
devicetree@...r.kernel.org,
dmitry.baryshkov@...aro.org,
gregkh@...uxfoundation.org,
hdegoede@...hat.com,
ilpo.jarvinen@...ux.intel.com,
jdelvare@...e.com,
konradybcio@...nel.org,
krzk+dt@...nel.org,
linux-arm-msm@...r.kernel.org,
linux-hwmon@...r.kernel.org,
linux-kernel@...r.kernel.org,
linux-pm@...r.kernel.org,
linux-usb@...r.kernel.org,
linux@...ck-us.net,
mitltlatltl@...il.com,
platform-driver-x86@...r.kernel.org,
robh@...nel.org,
sre@...nel.org
Subject: Re: [PATCH v2 3/5] usb: typec: ucsi: add Huawei Matebook E Go ucsi driver
On Tue, Jan 7, 2025 at 8:30 PM Heikki Krogerus <heikki.krogerus@...ux.intel.com> wrote:
>
> Hi,
>
> On Mon, Jan 06, 2025 at 01:41:57AM +0800, Pengyu Luo wrote:
> > The Huawei Matebook E Go tablet implements the UCSI interface in the
> > onboard EC. Add the glue driver to interface with the platform's UCSI
> > implementation.
> >
> > Signed-off-by: Pengyu Luo <mitltlatltl@...il.com>
> > ---
> > drivers/usb/typec/ucsi/Kconfig | 10 +
> > drivers/usb/typec/ucsi/Makefile | 1 +
> > drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c | 524 ++++++++++++++++++++
> > 3 files changed, 535 insertions(+)
> > create mode 100644 drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c
>
> This did not apply cleanly anymore, but I guess you'll be rebasing in
> any case. A few nitpicks below.
>
I see. I wrote them based on the mainline, then I formated them. I think
I should rebase to linux-next.
> > diff --git a/drivers/usb/typec/ucsi/Kconfig b/drivers/usb/typec/ucsi/Kconfig
> > index 680e1b87b..8a73df84a 100644
> > --- a/drivers/usb/typec/ucsi/Kconfig
> > +++ b/drivers/usb/typec/ucsi/Kconfig
> > @@ -78,4 +78,14 @@ config UCSI_LENOVO_YOGA_C630
> > To compile the driver as a module, choose M here: the module will be
> > called ucsi_yoga_c630.
> >
> > +config UCSI_HUAWEI_GAOKUN
> > + tristate "UCSI Interface Driver for Huawei Matebook E Go"
> > + depends on EC_HUAWEI_GAOKUN
> > + help
> > + This driver enables UCSI support on the Huawei Matebook E Go tablet,
> > + which is a sc8280xp-based 2-in-1 tablet.
> > +
> > + To compile the driver as a module, choose M here: the module will be
> > + called ucsi_huawei_gaokun.
> > +
> > endif
> > diff --git a/drivers/usb/typec/ucsi/Makefile b/drivers/usb/typec/ucsi/Makefile
> > index aed41d238..0b400122b 100644
> > --- a/drivers/usb/typec/ucsi/Makefile
> > +++ b/drivers/usb/typec/ucsi/Makefile
> > @@ -22,3 +22,4 @@ obj-$(CONFIG_UCSI_CCG) += ucsi_ccg.o
> > obj-$(CONFIG_UCSI_STM32G0) += ucsi_stm32g0.o
> > obj-$(CONFIG_UCSI_PMIC_GLINK) += ucsi_glink.o
> > obj-$(CONFIG_UCSI_LENOVO_YOGA_C630) += ucsi_yoga_c630.o
> > +obj-$(CONFIG_UCSI_HUAWEI_GAOKUN) += ucsi_huawei_gaokun.o
> > diff --git a/drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c b/drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c
> > new file mode 100644
> > index 000000000..044545b44
> > --- /dev/null
> > +++ b/drivers/usb/typec/ucsi/ucsi_huawei_gaokun.c
> > @@ -0,0 +1,524 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * ucsi-huawei-gaokun - A UCSI driver for HUAWEI Matebook E Go
> > + *
> > + * reference: drivers/usb/typec/ucsi/ucsi_yoga_c630.c
> > + * drivers/usb/typec/ucsi/ucsi_glink.c
> > + * drivers/soc/qcom/pmic_glink_altmode.c
> > + *
> > + * Copyright (C) 2024 Pengyu Luo <mitltlatltl@...il.com>
> > + */
> > +
> > +#include <drm/bridge/aux-bridge.h>
> > +#include <linux/auxiliary_bus.h>
> > +#include <linux/bitops.h>
> > +#include <linux/completion.h>
> > +#include <linux/container_of.h>
> > +#include <linux/module.h>
> > +#include <linux/notifier.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_data/huawei-gaokun-ec.h>
> > +#include <linux/string.h>
> > +#include <linux/usb/pd_vdo.h>
> > +#include <linux/usb/typec_altmode.h>
> > +#include <linux/usb/typec_dp.h>
> > +#include <linux/workqueue_types.h>
> > +
> > +#include "ucsi.h"
> > +
> > +#define EC_EVENT_UCSI 0x21
> > +#define EC_EVENT_USB 0x22
> > +
> > +#define GAOKUN_CCX_MASK GENMASK(1, 0)
> > +#define GAOKUN_MUX_MASK GENMASK(3, 2)
> > +
> > +#define GAOKUN_DPAM_MASK GENMASK(3, 0)
> > +#define GAOKUN_HPD_STATE_MASK BIT(4)
> > +#define GAOKUN_HPD_IRQ_MASK BIT(5)
> > +
> > +#define GET_IDX(updt) (ffs(updt) - 1)
> > +
> > +#define CCX_TO_ORI(ccx) (++ccx % 3) /* convert ccx to enum typec_orientation */
> > +
> > +/* Configuration Channel Extension */
> > +enum gaokun_ucsi_ccx {
> > + USBC_CCX_NORMAL,
> > + USBC_CCX_REVERSE,
> > + USBC_CCX_NONE,
> > +};
> > +
> > +enum gaokun_ucsi_mux {
> > + USBC_MUX_NONE,
> > + USBC_MUX_USB_2L,
> > + USBC_MUX_DP_4L,
> > + USBC_MUX_USB_DP,
> > +};
> > +/* based on pmic_glink_altmode_pin_assignment */
> > +enum gaokun_ucsi_dpam_pan { /* DP Alt Mode Pin Assignments */
> > + USBC_DPAM_PAN_NONE,
> > + USBC_DPAM_PAN_A, /* Not supported after USB Type-C Standard v1.0b */
> > + USBC_DPAM_PAN_B, /* Not supported after USB Type-C Standard v1.0b */
> > + USBC_DPAM_PAN_C, /* USBC_DPAM_PAN_C_REVERSE - 6 */
> > + USBC_DPAM_PAN_D,
> > + USBC_DPAM_PAN_E,
> > + USBC_DPAM_PAN_F, /* Not supported after USB Type-C Standard v1.0b */
> > + USBC_DPAM_PAN_A_REVERSE,/* Not supported after USB Type-C Standard v1.0b */
> > + USBC_DPAM_PAN_B_REVERSE,/* Not supported after USB Type-C Standard v1.0b */
> > + USBC_DPAM_PAN_C_REVERSE,
> > + USBC_DPAM_PAN_D_REVERSE,
> > + USBC_DPAM_PAN_E_REVERSE,
> > + USBC_DPAM_PAN_F_REVERSE,/* Not supported after USB Type-C Standard v1.0b */
> > +};
> > +
> > +struct gaokun_ucsi_reg {
> > + u8 port_num;
> > + u8 port_updt;
> > + u8 port_data[4];
> > + u8 checksum;
> > + u8 reserved;
> > +} __packed;
> > +
> > +struct gaokun_ucsi_port {
> > + struct completion usb_ack;
> > + spinlock_t lock;
> > +
> > + struct gaokun_ucsi *ucsi;
> > + struct auxiliary_device *bridge;
> > +
> > + int idx;
> > + enum gaokun_ucsi_ccx ccx;
> > + enum gaokun_ucsi_mux mux;
> > + u8 mode;
> > + u16 svid;
> > + u8 hpd_state;
> > + u8 hpd_irq;
> > +};
> > +
> > +struct gaokun_ucsi {
> > + struct gaokun_ec *ec;
> > + struct ucsi *ucsi;
> > + struct gaokun_ucsi_port *ports;
> > + struct device *dev;
> > + struct delayed_work work;
> > + struct notifier_block nb;
> > + u16 version;
> > + u8 port_num;
> > +};
> > +
> > +/* -------------------------------------------------------------------------- */
> > +/* For UCSI */
> > +
> > +static int gaokun_ucsi_read_version(struct ucsi *ucsi, u16 *version)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(ucsi);
> > +
> > + *version = uec->version;
> > +
> > + return 0;
> > +}
> > +
> > +static int gaokun_ucsi_read_cci(struct ucsi *ucsi, u32 *cci)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(ucsi);
> > + u8 buf[GAOKUN_UCSI_READ_SIZE];
> > + int ret;
> > +
> > + ret = gaokun_ec_ucsi_read(uec->ec, buf);
> > + if (ret)
> > + return ret;
> > +
> > + memcpy(cci, buf, sizeof(*cci));
> > +
> > + return 0;
> > +}
> > +
> > +static int gaokun_ucsi_read_message_in(struct ucsi *ucsi,
> > + void *val, size_t val_len)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(ucsi);
> > + u8 buf[GAOKUN_UCSI_READ_SIZE];
> > + int ret;
> > +
> > + ret = gaokun_ec_ucsi_read(uec->ec, buf);
> > + if (ret)
> > + return ret;
> > +
> > + memcpy(val, buf + GAOKUN_UCSI_CCI_SIZE,
> > + min(val_len, GAOKUN_UCSI_DATA_SIZE));
> > +
> > + return 0;
> > +}
> > +
> > +static int gaokun_ucsi_async_control(struct ucsi *ucsi, u64 command)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(ucsi);
> > + u8 buf[GAOKUN_UCSI_WRITE_SIZE] = {};
> > +
> > + memcpy(buf, &command, sizeof(command));
> > +
> > + return gaokun_ec_ucsi_write(uec->ec, buf);
> > +}
> > +
> > +static void gaokun_ucsi_update_connector(struct ucsi_connector *con)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(con->ucsi);
> > +
> > + if (con->num > uec->port_num)
> > + return;
> > +
> > + con->typec_cap.orientation_aware = true;
> > +}
> > +
> > +static void gaokun_set_orientation(struct ucsi_connector *con,
> > + struct gaokun_ucsi_port *port)
> > +{
> > + enum gaokun_ucsi_ccx ccx;
> > + unsigned long flags;
> > +
> > + spin_lock_irqsave(&port->lock, flags);
> > + ccx = port->ccx;
> > + spin_unlock_irqrestore(&port->lock, flags);
> > +
> > + typec_set_orientation(con->port, CCX_TO_ORI(ccx));
> > +}
> > +
> > +static void gaokun_ucsi_connector_status(struct ucsi_connector *con)
> > +{
> > + struct gaokun_ucsi *uec = ucsi_get_drvdata(con->ucsi);
> > + int idx;
> > +
> > + idx = con->num - 1;
> > + if (con->num > uec->port_num) {
> > + dev_warn(uec->dev, "set orientation out of range: con%d\n", idx);
> > + return;
> > + }
> > +
> > + gaokun_set_orientation(con, &uec->ports[idx]);
> > +}
> > +
> > +const struct ucsi_operations gaokun_ucsi_ops = {
> > + .read_version = gaokun_ucsi_read_version,
> > + .read_cci = gaokun_ucsi_read_cci,
> > + .read_message_in = gaokun_ucsi_read_message_in,
> > + .sync_control = ucsi_sync_control_common,
> > + .async_control = gaokun_ucsi_async_control,
> > + .update_connector = gaokun_ucsi_update_connector,
> > + .connector_status = gaokun_ucsi_connector_status,
> > +};
> > +
> > +/* -------------------------------------------------------------------------- */
> > +/* For Altmode */
> > +
> > +static void gaokun_ucsi_port_update(struct gaokun_ucsi_port *port,
> > + const u8 *port_data)
> > +{
> > + struct gaokun_ucsi *uec = port->ucsi;
> > + int offset = port->idx * 2; /* every port has 2 Bytes data */
> > + unsigned long flags;
> > + u8 dcc, ddi;
> > +
> > + dcc = port_data[offset];
> > + ddi = port_data[offset + 1];
> > +
> > + spin_lock_irqsave(&port->lock, flags);
> > +
> > + port->ccx = FIELD_GET(GAOKUN_CCX_MASK, dcc);
> > + port->mux = FIELD_GET(GAOKUN_MUX_MASK, dcc);
> > + port->mode = FIELD_GET(GAOKUN_DPAM_MASK, ddi);
> > + port->hpd_state = FIELD_GET(GAOKUN_HPD_STATE_MASK, ddi);
> > + port->hpd_irq = FIELD_GET(GAOKUN_HPD_IRQ_MASK, ddi);
> > +
> > + /* Mode and SVID are unused; keeping them to make things clearer */
> > + switch (port->mode) {
> > + case USBC_DPAM_PAN_C:
> > + case USBC_DPAM_PAN_C_REVERSE:
> > + port->mode = DP_PIN_ASSIGN_C; /* correct it for usb later */
> > + break;
> > + case USBC_DPAM_PAN_D:
> > + case USBC_DPAM_PAN_D_REVERSE:
> > + port->mode = DP_PIN_ASSIGN_D;
> > + break;
> > + case USBC_DPAM_PAN_E:
> > + case USBC_DPAM_PAN_E_REVERSE:
> > + port->mode = DP_PIN_ASSIGN_E;
> > + break;
> > + case USBC_DPAM_PAN_NONE:
> > + port->mode = TYPEC_STATE_SAFE;
> > + break;
> > + default:
> > + dev_warn(uec->dev, "unknow mode %d\n", port->mode);
> > + break;
> > + }
> > +
> > + switch (port->mux) {
> > + case USBC_MUX_NONE:
> > + port->svid = 0;
> > + break;
> > + case USBC_MUX_USB_2L:
> > + port->svid = USB_SID_PD;
> > + port->mode = TYPEC_STATE_USB; /* same as PAN_C, correct it */
> > + break;
> > + case USBC_MUX_DP_4L:
> > + case USBC_MUX_USB_DP:
> > + port->svid = USB_SID_DISPLAYPORT;
> > + break;
> > + default:
> > + dev_warn(uec->dev, "unknow mux state %d\n", port->mux);
> > + break;
> > + }
> > +
> > + spin_unlock_irqrestore(&port->lock, flags);
> > +}
> > +
> > +static int gaokun_ucsi_refresh(struct gaokun_ucsi *uec)
> > +{
> > + struct gaokun_ucsi_reg ureg;
> > + int ret, idx;
> > +
> > + ret = gaokun_ec_ucsi_get_reg(uec->ec, (u8 *)&ureg);
> > + if (ret)
> > + return GAOKUN_UCSI_NO_PORT_UPDATE;
> > +
> > + uec->port_num = ureg.port_num;
> > + idx = GET_IDX(ureg.port_updt);
> > +
> > + if (idx < 0 || idx >= ureg.port_num)
> > + return GAOKUN_UCSI_NO_PORT_UPDATE;
> > +
> > + gaokun_ucsi_port_update(&uec->ports[idx], ureg.port_data);
> > + return idx;
> > +}
> > +
> > +static void gaokun_ucsi_handle_altmode(struct gaokun_ucsi_port *port)
> > +{
> > + struct gaokun_ucsi *uec = port->ucsi;
> > + int idx = port->idx;
> > +
> > + if (idx >= uec->ucsi->cap.num_connectors) {
> > + dev_warn(uec->dev, "altmode port out of range: %d\n", idx);
> > + return;
> > + }
> > +
> > + /* UCSI callback .connector_status() have set orientation */
> > + if (port->bridge)
> > + drm_aux_hpd_bridge_notify(&port->bridge->dev,
> > + port->hpd_state ?
> > + connector_status_connected :
> > + connector_status_disconnected);
> > +
> > + gaokun_ec_ucsi_pan_ack(uec->ec, port->idx);
> > +}
> > +
> > +static void gaokun_ucsi_altmode_notify_ind(struct gaokun_ucsi *uec)
> > +{
> > + int idx;
> > +
> > + if (!uec->ucsi->connector) { /* slow to register */
> > + dev_err(uec->dev, "ucsi connector is not initialized yet\n");
> > + return;
> > + }
> > +
> > + idx = gaokun_ucsi_refresh(uec);
> > + if (idx == GAOKUN_UCSI_NO_PORT_UPDATE)
> > + gaokun_ec_ucsi_pan_ack(uec->ec, idx); /* ack directly if no update */
> > + else
> > + gaokun_ucsi_handle_altmode(&uec->ports[idx]);
> > +}
> > +
> > +/*
> > + * USB event is necessary for enabling altmode, the event should follow
> > + * UCSI event, if not after timeout(this notify may be disabled somehow),
> > + * then force to enable altmode.
> > + */
> > +static void gaokun_ucsi_handle_no_usb_event(struct gaokun_ucsi *uec, int idx)
> > +{
> > + struct gaokun_ucsi_port *port;
> > +
> > + port = &uec->ports[idx];
> > + if (!wait_for_completion_timeout(&port->usb_ack, 2 * HZ)) {
> > + dev_warn(uec->dev, "No USB EVENT, triggered by UCSI EVENT");
> > + gaokun_ucsi_altmode_notify_ind(uec);
> > + }
> > +}
> > +
> > +static int gaokun_ucsi_notify(struct notifier_block *nb,
> > + unsigned long action, void *data)
> > +{
> > + u32 cci;
> > + struct gaokun_ucsi *uec = container_of(nb, struct gaokun_ucsi, nb);
> > +
> > + switch (action) {
> > + case EC_EVENT_USB:
> > + gaokun_ucsi_altmode_notify_ind(uec);
> > + return NOTIFY_OK;
> > +
> > + case EC_EVENT_UCSI:
> > + uec->ucsi->ops->read_cci(uec->ucsi, &cci);
>
> I think it would be more clear here to just call
> gaokun_ucsi_read_cci() directly here.
>
Agree
> > + ucsi_notify_common(uec->ucsi, cci);
> > + if (UCSI_CCI_CONNECTOR(cci))
> > + gaokun_ucsi_handle_no_usb_event(uec, UCSI_CCI_CONNECTOR(cci) - 1);
> > +
> > + return NOTIFY_OK;
> > +
> > + default:
> > + return NOTIFY_DONE;
> > + }
> > +}
> > +
> > +static inline int gaokun_ucsi_get_port_num(struct gaokun_ucsi *uec)
> > +{
> > + struct gaokun_ucsi_reg ureg;
> > + int ret;
> > +
> > + ret = gaokun_ec_ucsi_get_reg(uec->ec, (u8 *)&ureg);
> > +
> > + return ret ? 0 : ureg.port_num;
> > +}
>
> This function does not look like it's necessary to me.
>
Agree
> > +static int gaokun_ucsi_ports_init(struct gaokun_ucsi *uec)
> > +{
> > + u32 port;
> > + int i, ret, port_num;
> > + struct device *dev = uec->dev;
> > + struct gaokun_ucsi_port *ucsi_port;
> > + struct fwnode_handle *fwnode;
> > +
> > + port_num = gaokun_ucsi_get_port_num(uec);
> > + uec->port_num = port_num;
>
> struct gaokun_ucsi_reg ureg = { };
>
> gaokun_ec_ucsi_get_reg(uec->ec, &ureg);
> port_num = ureg->port_num;
>
> (Btw. port_num here is confusing IMO, because you are not talking
> about the number of a port, but instead number of all ports. So
> something like num_ports or nports would be better).
>
Agree
> > + uec->ports = devm_kcalloc(dev, port_num, sizeof(*(uec->ports)),
> > + GFP_KERNEL);
> > + if (!uec->ports)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < port_num; ++i) {
> > + ucsi_port = &uec->ports[i];
> > + ucsi_port->ccx = USBC_CCX_NONE;
> > + ucsi_port->idx = i;
> > + ucsi_port->ucsi = uec;
> > + init_completion(&ucsi_port->usb_ack);
> > + spin_lock_init(&ucsi_port->lock);
> > + }
> > +
> > + device_for_each_child_node(dev, fwnode) {
> > + ret = fwnode_property_read_u32(fwnode, "reg", &port);
> > + if (ret < 0) {
> > + dev_err(dev, "missing reg property of %pOFn\n", fwnode);
> > + fwnode_handle_put(fwnode);
> > + return ret;
> > + }
> > +
> > + if (port >= port_num) {
> > + dev_warn(dev, "invalid connector number %d, ignoring\n", port);
> > + continue;
> > + }
> > +
> > + ucsi_port = &uec->ports[port];
> > + ucsi_port->bridge = devm_drm_dp_hpd_bridge_alloc(dev, to_of_node(fwnode));
> > + if (IS_ERR(ucsi_port->bridge)) {
> > + fwnode_handle_put(fwnode);
> > + return PTR_ERR(ucsi_port->bridge);
> > + }
> > + }
> > +
> > + for (i = 0; i < port_num; i++) {
> > + if (!uec->ports[i].bridge)
> > + continue;
> > +
> > + ret = devm_drm_dp_hpd_bridge_add(dev, uec->ports[i].bridge);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void gaokun_ucsi_register_worker(struct work_struct *work)
> > +{
> > + struct gaokun_ucsi *uec;
> > + struct ucsi *ucsi;
> > + int ret;
> > +
> > + uec = container_of(work, struct gaokun_ucsi, work.work);
> > + ucsi = uec->ucsi;
> > + /* This may be a problem specific to sc8280xp-based machines */
> > + ucsi->quirks = UCSI_NO_PARTNER_PDOS | UCSI_DELAY_DEVICE_PDOS;
> > +
> > + ret = gaokun_ec_register_notify(uec->ec, &uec->nb);
> > + if (ret) {
> > + dev_err_probe(ucsi->dev, ret, "notifier register failed\n");
> > + return;
> > + }
> > +
> > + ret = ucsi_register(ucsi);
> > + if (ret)
> > + dev_err_probe(ucsi->dev, ret, "ucsi register failed\n");
> > +}
> > +
> > +static inline int gaokun_ucsi_register(struct gaokun_ucsi *uec)
> > +{
> > + /* EC can't handle UCSI properly in the early stage */
> > + schedule_delayed_work(&uec->work, 3 * HZ);
> > +
> > + return 0;
> > +}
>
> This whole function is unnecessary.
>
I see, I will move it to probe function
> > +static int gaokun_ucsi_probe(struct auxiliary_device *adev,
> > + const struct auxiliary_device_id *id)
> > +{
> > + struct gaokun_ec *ec = adev->dev.platform_data;
> > + struct device *dev = &adev->dev;
> > + struct gaokun_ucsi *uec;
> > + int ret;
> > +
> > + uec = devm_kzalloc(dev, sizeof(*uec), GFP_KERNEL);
> > + if (!uec)
> > + return -ENOMEM;
> > +
> > + uec->ec = ec;
> > + uec->dev = dev;
> > + uec->version = 0x0100;
>
> Please add a definition for UCSI v1.0 to ucsi.h (separate patch).
>
Understood
> > + uec->nb.notifier_call = gaokun_ucsi_notify;
> > +
> > + INIT_DELAYED_WORK(&uec->work, gaokun_ucsi_register_worker);
> > +
> > + ret = gaokun_ucsi_ports_init(uec);
> > + if (ret)
> > + return ret;
> > +
> > + uec->ucsi = ucsi_create(dev, &gaokun_ucsi_ops);
> > + if (IS_ERR(uec->ucsi))
> > + return PTR_ERR(uec->ucsi);
> > +
> > + ucsi_set_drvdata(uec->ucsi, uec);
> > + auxiliary_set_drvdata(adev, uec);
> > +
> > + return gaokun_ucsi_register(uec);
> > +}
> > +
> > +static void gaokun_ucsi_remove(struct auxiliary_device *adev)
> > +{
> > + struct gaokun_ucsi *uec = auxiliary_get_drvdata(adev);
> > +
> > + gaokun_ec_unregister_notify(uec->ec, &uec->nb);
> > + ucsi_unregister(uec->ucsi);
> > + ucsi_destroy(uec->ucsi);
> > +}
> > +
> > +static const struct auxiliary_device_id gaokun_ucsi_id_table[] = {
> > + { .name = GAOKUN_MOD_NAME "." GAOKUN_DEV_UCSI, },
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(auxiliary, gaokun_ucsi_id_table);
> > +
> > +static struct auxiliary_driver gaokun_ucsi_driver = {
> > + .name = GAOKUN_DEV_UCSI,
> > + .id_table = gaokun_ucsi_id_table,
> > + .probe = gaokun_ucsi_probe,
> > + .remove = gaokun_ucsi_remove,
> > +};
> > +
> > +module_auxiliary_driver(gaokun_ucsi_driver);
> > +
> > +MODULE_DESCRIPTION("HUAWEI Matebook E Go UCSI driver");
> > +MODULE_LICENSE("GPL");
>
> thanks,
>
> --
> heikki
Best wishes,
Pengyu
Powered by blists - more mailing lists