linux-kernel - Re: [PATCH v3 4/4] arm64: dts: qcom: ipq5424: Enable PCIe PHYs and controllers

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <3e92c8e2-7745-4205-8a48-5ef783b098a2@oss.qualcomm.com>
Date: Tue, 28 Jan 2025 12:39:31 +0100
From: Konrad Dybcio <konrad.dybcio@....qualcomm.com>
To: Manikanta Mylavarapu <quic_mmanikan@...cinc.com>, andersson@...nel.org,
        mturquette@...libre.com, sboyd@...nel.org, robh@...nel.org,
        krzk+dt@...nel.org, conor+dt@...nel.org, lpieralisi@...nel.org,
        kw@...ux.com, manivannan.sadhasivam@...aro.org, bhelgaas@...gle.com,
        konradybcio@...nel.org, linux-arm-msm@...r.kernel.org,
        linux-clk@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, linux-pci@...r.kernel.org
Cc: quic_srichara@...cinc.com, quic_varada@...cinc.com
Subject: Re: [PATCH v3 4/4] arm64: dts: qcom: ipq5424: Enable PCIe PHYs and
 controllers

On 25.01.2025 4:59 AM, Manikanta Mylavarapu wrote:
> Enable the PCIe controller and PHY nodes corresponding to RDP466.
> 
> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@...cinc.com>
> ---
> Changes in V3:
> 	- No change.
> 
>  arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts | 41 ++++++++++++++++++++-
>  1 file changed, 40 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> index b6e4bb3328b3..73e6b38ecc26 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> @@ -53,6 +53,30 @@ &dwc_1 {
>  	dr_mode = "host";
>  };
>  
> +&pcie2 {
> +	pinctrl-0 = <&pcie2_default_state>;
> +	pinctrl-names = "default";
> +
> +	perst-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
> +	status = "okay";

Please add a new line before 'status'

> +};
> +
> +&pcie2_phy {
> +	status = "okay";
> +};
> +
> +&pcie3 {
> +	pinctrl-0 = <&pcie3_default_state>;
> +	pinctrl-names = "default";
> +
> +	perst-gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&pcie3_phy {
> +	status = "okay";
> +};
> +
>  &qusb_phy_0 {
>  	vdd-supply = <&vreg_misc_0p925>;
>  	vdda-pll-supply = <&vreg_misc_1p8>;
> @@ -147,6 +171,22 @@ data-pins {
>  			bias-pull-up;
>  		};
>  	};
> +
> +	pcie2_default_state: pcie2-default-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-up;
> +		output-low;
> +	};
> +
> +	pcie3_default_state: pcie3-default-state {
> +		pins = "gpio34";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-up;
> +		output-low;

The GPIO APIs are in control of in/out state instead, please remove the
last property from both entries

Konrad