| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <a2895a6f-0cb1-4ed2-8bbf-9daa4041d03d@amlogic.com>
Date: Wed, 5 Feb 2025 14:00:08 +0800
From: Keke Li <keke.li@...ogic.com>
To: Jacopo Mondi <jacopo.mondi@...asonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@...nel.org>, Rob Herring
<robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, linux-media@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
kieran.bingham@...asonboard.com, laurent.pinchart@...asonboard.com,
dan.scally@...asonboard.com
Subject: Re: [PATCH v5 02/10] media: platform: Add C3 MIPI CSI-2 driver
Hi Jacopo
Thanks very much for your reply.
On 2025/1/23 16:59, Jacopo Mondi wrote:
> [ EXTERNAL EMAIL ]
>
> Hi again Keke
>
> On Fri, Dec 27, 2024 at 03:09:11PM +0800, Keke Li via B4 Relay wrote:
>> From: Keke Li <keke.li@...ogic.com>
>>
>> Add a driver for the CSI-2 receiver uinit found on the Amlofic C3 SoC.
>>
>> Create a drivers/media/platform/amlogic/c3/ directory to host the driver
>> and the forthcoming support for the Amlogic C3 MIPI adapter and C3 ISP.
>>
>> This driver is used to receive the MIPI data from image sensor.
>>
>> Reviewed-by: Daniel Scally <dan.scally@...asonboard.com>
>> Signed-off-by: Keke Li <keke.li@...ogic.com>
>> ---
>> MAINTAINERS | 1 +
>> drivers/media/platform/amlogic/Kconfig | 1 +
>> drivers/media/platform/amlogic/Makefile | 2 +
>> drivers/media/platform/amlogic/c3/Kconfig | 3 +
>> drivers/media/platform/amlogic/c3/Makefile | 3 +
>> .../media/platform/amlogic/c3/mipi-csi2/Kconfig | 16 +
>> .../media/platform/amlogic/c3/mipi-csi2/Makefile | 3 +
>> .../platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c | 831 +++++++++++++++++++++
>> 8 files changed, 860 insertions(+)
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 2b06962db506..1d1416b15570 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -1248,6 +1248,7 @@ M: Keke Li <keke.li@...ogic.com>
>> L: linux-media@...r.kernel.org
>> S: Maintained
>> F: Documentation/devicetree/bindings/media/amlogic,c3-mipi-csi2.yaml
>> +F: drivers/media/platform/amlogic/c3/mipi-csi2/
>>
>> AMLOGIC RTC DRIVER
>> M: Yiting Deng <yiting.deng@...ogic.com>
>> diff --git a/drivers/media/platform/amlogic/Kconfig b/drivers/media/platform/amlogic/Kconfig
>> index 5014957404e9..458acf3d5fa8 100644
>> --- a/drivers/media/platform/amlogic/Kconfig
>> +++ b/drivers/media/platform/amlogic/Kconfig
>> @@ -2,4 +2,5 @@
>>
>> comment "Amlogic media platform drivers"
>>
>> +source "drivers/media/platform/amlogic/c3/Kconfig"
>> source "drivers/media/platform/amlogic/meson-ge2d/Kconfig"
>> diff --git a/drivers/media/platform/amlogic/Makefile b/drivers/media/platform/amlogic/Makefile
>> index d3cdb8fa4ddb..c744afcd1b9e 100644
>> --- a/drivers/media/platform/amlogic/Makefile
>> +++ b/drivers/media/platform/amlogic/Makefile
>> @@ -1,2 +1,4 @@
>> # SPDX-License-Identifier: GPL-2.0-only
>> +
>> +obj-y += c3/
>> obj-y += meson-ge2d/
>> diff --git a/drivers/media/platform/amlogic/c3/Kconfig b/drivers/media/platform/amlogic/c3/Kconfig
>> new file mode 100644
>> index 000000000000..098d458747b8
>> --- /dev/null
>> +++ b/drivers/media/platform/amlogic/c3/Kconfig
>> @@ -0,0 +1,3 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +
>> +source "drivers/media/platform/amlogic/c3/mipi-csi2/Kconfig"
>> diff --git a/drivers/media/platform/amlogic/c3/Makefile b/drivers/media/platform/amlogic/c3/Makefile
>> new file mode 100644
>> index 000000000000..a468fb782f94
>> --- /dev/null
>> +++ b/drivers/media/platform/amlogic/c3/Makefile
>> @@ -0,0 +1,3 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +
>> +obj-y += mipi-csi2/
>> diff --git a/drivers/media/platform/amlogic/c3/mipi-csi2/Kconfig b/drivers/media/platform/amlogic/c3/mipi-csi2/Kconfig
>> new file mode 100644
>> index 000000000000..0d7b2e203273
>> --- /dev/null
>> +++ b/drivers/media/platform/amlogic/c3/mipi-csi2/Kconfig
>> @@ -0,0 +1,16 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +
>> +config VIDEO_C3_MIPI_CSI2
>> + tristate "Amlogic C3 MIPI CSI-2 receiver"
>> + depends on ARCH_MESON || COMPILE_TEST
>> + depends on VIDEO_DEV
>> + depends on OF
>> + select MEDIA_CONTROLLER
>> + select V4L2_FWNODE
>> + select VIDEO_V4L2_SUBDEV_API
>> + help
>> + Video4Linux2 driver for Amlogic C3 MIPI CSI-2 receiver.
>> + C3 MIPI CSI-2 receiver is used to receive MIPI data from
>> + image sensor.
>> +
>> + To compile this driver as a module choose m here.
>> diff --git a/drivers/media/platform/amlogic/c3/mipi-csi2/Makefile b/drivers/media/platform/amlogic/c3/mipi-csi2/Makefile
>> new file mode 100644
>> index 000000000000..cc08fc722bfd
>> --- /dev/null
>> +++ b/drivers/media/platform/amlogic/c3/mipi-csi2/Makefile
>> @@ -0,0 +1,3 @@
>> +# SPDX-License-Identifier: GPL-2.0-only
>> +
>> +obj-$(CONFIG_VIDEO_C3_MIPI_CSI2) += c3-mipi-csi2.o
>> diff --git a/drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c b/drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c
>> new file mode 100644
>> index 000000000000..7343e7003d13
>> --- /dev/null
>> +++ b/drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c
>> @@ -0,0 +1,831 @@
>> +// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
>> +/*
>> + * Copyright (C) 2024 Amlogic, Inc. All rights reserved
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/device.h>
>> +#include <linux/module.h>
>> +#include <linux/mutex.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/pm_runtime.h>
>> +
>> +#include <media/v4l2-async.h>
>> +#include <media/v4l2-common.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-fwnode.h>
>> +#include <media/v4l2-mc.h>
>> +#include <media/v4l2-subdev.h>
>> +
>> +/* C3 CSI-2 submodule definition */
>> +enum {
>> + SUBMD_APHY,
>> + SUBMD_DPHY,
>> + SUBMD_HOST,
>> +};
>> +
>> +#define CSI2_SUBMD_MASK GENMASK(17, 16)
>> +#define CSI2_SUBMD_SHIFT 16
>> +#define CSI2_SUBMD(x) (((x) & (CSI2_SUBMD_MASK)) >> (CSI2_SUBMD_SHIFT))
>> +#define CSI2_REG_ADDR_MASK GENMASK(15, 0)
>> +#define CSI2_REG_ADDR(x) ((x) & (CSI2_REG_ADDR_MASK))
>> +#define CSI2_REG_A(x) ((SUBMD_APHY << CSI2_SUBMD_SHIFT) | (x))
>> +#define CSI2_REG_D(x) ((SUBMD_DPHY << CSI2_SUBMD_SHIFT) | (x))
>> +#define CSI2_REG_H(x) ((SUBMD_HOST << CSI2_SUBMD_SHIFT) | (x))
>> +
>> +#define MIPI_CSI2_CLOCK_NUM_MAX 3
>> +#define MIPI_CSI2_SUBDEV_NAME "c3-mipi-csi2"
>> +
>> +/* C3 CSI-2 APHY register */
>> +#define CSI_PHY_CNTL0 CSI2_REG_A(0x44)
>> +#define CSI_PHY_CNTL0_HS_LP_BIAS_EN BIT(10)
>> +#define CSI_PHY_CNTL0_HS_RX_TRIM_11 (11 << 11)
>> +#define CSI_PHY_CNTL0_LP_LOW_VTH_2 (2 << 16)
>> +#define CSI_PHY_CNTL0_LP_HIGH_VTH_4 (4 << 20)
>> +#define CSI_PHY_CNTL0_DATA_LANE0_HS_DIG_EN BIT(24)
>> +#define CSI_PHY_CNTL0_DATA_LANE1_HS_DIG_EN BIT(25)
>> +#define CSI_PHY_CNTL0_CLK0_LANE_HS_DIG_EN BIT(26)
>> +#define CSI_PHY_CNTL0_DATA_LANE2_HS_DIG_EN BIT(27)
>> +#define CSI_PHY_CNTL0_DATA_LANE3_HS_DIG_EN BIT(28)
>> +
>> +#define CSI_PHY_CNTL1 CSI2_REG_A(0x48)
>> +#define CSI_PHY_CNTL1_HS_EQ_CAP_SMALL (2 << 16)
>> +#define CSI_PHY_CNTL1_HS_EQ_CAP_BIG (3 << 16)
>> +#define CSI_PHY_CNTL1_HS_EQ_RES_MIN (3 << 18)
>> +#define CSI_PHY_CNTL1_HS_EQ_RES_MED (2 << 18)
>> +#define CSI_PHY_CNTL1_HS_EQ_RES_MAX BIT(18)
>> +#define CSI_PHY_CNTL1_CLK_CHN_EQ_MAX_GAIN BIT(20)
>> +#define CSI_PHY_CNTL1_DATA_CHN_EQ_MAX_GAIN BIT(21)
>> +#define CSI_PHY_CNTL1_COM_BG_EN BIT(24)
>> +#define CSI_PHY_CNTL1_HS_SYNC_EN BIT(25)
>> +
>> +/* C3 CSI-2 DPHY register */
>> +#define MIPI_PHY_CTRL CSI2_REG_D(0x00)
>> +#define MIPI_PHY_CTRL_DATA_LANE0_EN (0 << 0)
>> +#define MIPI_PHY_CTRL_DATA_LANE0_DIS BIT(0)
>> +#define MIPI_PHY_CTRL_DATA_LANE1_EN (0 << 1)
>> +#define MIPI_PHY_CTRL_DATA_LANE1_DIS BIT(1)
>> +#define MIPI_PHY_CTRL_DATA_LANE2_EN (0 << 2)
>> +#define MIPI_PHY_CTRL_DATA_LANE2_DIS BIT(2)
>> +#define MIPI_PHY_CTRL_DATA_LANE3_EN (0 << 3)
>> +#define MIPI_PHY_CTRL_DATA_LANE3_DIS BIT(3)
>> +#define MIPI_PHY_CTRL_CLOCK_LANE_EN (0 << 4)
>> +#define MIPI_PHY_CTRL_CLOCK_LANE_DIS BIT(4)
>> +
>> +#define MIPI_PHY_CLK_LANE_CTRL CSI2_REG_D(0x04)
>> +#define MIPI_PHY_CLK_LANE_CTRL_FORCE_ULPS_ENTER BIT(0)
>> +#define MIPI_PHY_CLK_LANE_CTRL_FORCE_ULPS_EXIT BIT(1)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS (0 << 3)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS_2 BIT(3)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS_4 (2 << 3)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS_8 (3 << 3)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS_16 (4 << 3)
>> +#define MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_EN BIT(6)
>> +#define MIPI_PHY_CLK_LANE_CTRL_LPEN_DIS BIT(7)
>> +#define MIPI_PHY_CLK_LANE_CTRL_END_EN BIT(8)
>> +#define MIPI_PHY_CLK_LANE_CTRL_HS_RX_EN BIT(9)
>> +
>> +#define MIPI_PHY_DATA_LANE_CTRL1 CSI2_REG_D(0x0c)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_INSERT_ERRESC BIT(0)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_HS_SYNC_CHK_EN BIT(1)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_PIPE_MASK GENMASK(6, 2)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_PIPE_ALL_EN (0x1f << 2)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_PIPE_DELAY_MASK GENMASK(9, 7)
>> +#define MIPI_PHY_DATA_LANE_CTRL1_PIPE_DELAY_3 (3 << 7)
>> +
>> +#define MIPI_PHY_TCLK_MISS CSI2_REG_D(0x10)
>> +#define MIPI_PHY_TCLK_MISS_CYCLES_MASK GENMASK(7, 0)
>> +#define MIPI_PHY_TCLK_MISS_CYCLES_9 (9 << 0)
>> +
>> +#define MIPI_PHY_TCLK_SETTLE CSI2_REG_D(0x14)
>> +#define MIPI_PHY_TCLK_SETTLE_CYCLES_MASK GENMASK(7, 0)
>> +#define MIPI_PHY_TCLK_SETTLE_CYCLES_31 (31 << 0)
>> +
>> +#define MIPI_PHY_THS_EXIT CSI2_REG_D(0x18)
>> +#define MIPI_PHY_THS_EXIT_CYCLES_MASK GENMASK(7, 0)
>> +#define MIPI_PHY_THS_EXIT_CYCLES_8 (8 << 0)
>> +
>> +#define MIPI_PHY_THS_SKIP CSI2_REG_D(0x1c)
>> +#define MIPI_PHY_THS_SKIP_CYCLES_MASK GENMASK(7, 0)
>> +#define MIPI_PHY_THS_SKIP_CYCLES_10 (10 << 0)
>> +
>> +#define MIPI_PHY_THS_SETTLE CSI2_REG_D(0x20)
>> +#define MIPI_PHY_THS_SETTLE_CYCLES_MASK GENMASK(7, 0)
>> +
>> +#define MIPI_PHY_TINIT CSI2_REG_D(0x24)
>> +#define MIPI_PHY_TINIT_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TINIT_CYCLES_20000 (20000 << 0)
>> +
>> +#define MIPI_PHY_TULPS_C CSI2_REG_D(0x28)
>> +#define MIPI_PHY_TULPS_C_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TULPS_C_CYCLES_4096 (4096 << 0)
>> +
>> +#define MIPI_PHY_TULPS_S CSI2_REG_D(0x2c)
>> +#define MIPI_PHY_TULPS_S_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TULPS_S_CYCLES_256 (256 << 0)
>> +
>> +#define MIPI_PHY_TMBIAS CSI2_REG_D(0x30)
>> +#define MIPI_PHY_TMBIAS_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TMBIAS_CYCLES_256 (256 << 0)
>> +
>> +#define MIPI_PHY_TLP_EN_W CSI2_REG_D(0x34)
>> +#define MIPI_PHY_TLP_EN_W_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TLP_EN_W_CYCLES_12 (12 << 0)
>> +
>> +#define MIPI_PHY_TLPOK CSI2_REG_D(0x38)
>> +#define MIPI_PHY_TLPOK_CYCLES_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TLPOK_CYCLES_256 (256 << 0)
>> +
>> +#define MIPI_PHY_TWD_INIT CSI2_REG_D(0x3c)
>> +#define MIPI_PHY_TWD_INIT_DOG_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TWD_INIT_DOG_0X400000 (0x400000 << 0)
>> +
>> +#define MIPI_PHY_TWD_HS CSI2_REG_D(0x40)
>> +#define MIPI_PHY_TWD_HS_DOG_MASK GENMASK(31, 0)
>> +#define MIPI_PHY_TWD_HS_DOG_0X400000 (0x400000 << 0)
>> +
>> +#define MIPI_PHY_MUX_CTRL0 CSI2_REG_D(0x284)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN3_SRC_MASK GENMASK(3, 0)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN3_SRC_LANE0 (0 << 0)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN3_SRC_LANE1 BIT(0)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN3_SRC_LANE2 (2 << 0)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN3_SRC_LANE3 (3 << 0)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN2_SRC_MASK GENMASK(7, 4)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN2_SRC_LANE0 (0 << 4)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN2_SRC_LANE1 BIT(4)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN2_SRC_LANE2 (2 << 4)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN2_SRC_LANE3 (3 << 4)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN1_SRC_MASK GENMASK(11, 8)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN1_SRC_LANE0 (0 << 8)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN1_SRC_LANE1 BIT(8)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN1_SRC_LANE2 (2 << 8)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN1_SRC_LANE3 (3 << 8)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN0_SRC_MASK GENMASK(14, 12)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN0_SRC_LANE0 (0 << 12)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN0_SRC_LANE1 BIT(12)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN0_SRC_LANE2 (2 << 12)
>> +#define MIPI_PHY_MUX_CTRL0_SFEN0_SRC_LANE3 (3 << 12)
>> +
>> +#define MIPI_PHY_MUX_CTRL1 CSI2_REG_D(0x288)
>> +#define MIPI_PHY_MUX_CTRL1_LANE3_SRC_MASK GENMASK(3, 0)
>> +#define MIPI_PHY_MUX_CTRL1_LANE3_SRC_SFEN0 (0 << 0)
>> +#define MIPI_PHY_MUX_CTRL1_LANE3_SRC_SFEN1 BIT(0)
>> +#define MIPI_PHY_MUX_CTRL1_LANE3_SRC_SFEN2 (2 << 0)
>> +#define MIPI_PHY_MUX_CTRL1_LANE3_SRC_SFEN3 (3 << 0)
>> +#define MIPI_PHY_MUX_CTRL1_LANE2_SRC_MASK GENMASK(7, 4)
>> +#define MIPI_PHY_MUX_CTRL1_LANE2_SRC_SFEN0 (0 << 4)
>> +#define MIPI_PHY_MUX_CTRL1_LANE2_SRC_SFEN1 BIT(4)
>> +#define MIPI_PHY_MUX_CTRL1_LANE2_SRC_SFEN2 (2 << 4)
>> +#define MIPI_PHY_MUX_CTRL1_LANE2_SRC_SFEN3 (3 << 4)
>> +#define MIPI_PHY_MUX_CTRL1_LANE1_SRC_MASK GENMASK(11, 8)
>> +#define MIPI_PHY_MUX_CTRL1_LANE1_SRC_SFEN0 (0 << 8)
>> +#define MIPI_PHY_MUX_CTRL1_LANE1_SRC_SFEN1 BIT(8)
>> +#define MIPI_PHY_MUX_CTRL1_LANE1_SRC_SFEN2 (2 << 8)
>> +#define MIPI_PHY_MUX_CTRL1_LANE1_SRC_SFEN3 (3 << 8)
>> +#define MIPI_PHY_MUX_CTRL1_LANE0_SRC_MASK GENMASK(14, 12)
>> +#define MIPI_PHY_MUX_CTRL1_LANE0_SRC_SFEN0 (0 << 12)
>> +#define MIPI_PHY_MUX_CTRL1_LANE0_SRC_SFEN1 BIT(12)
>> +#define MIPI_PHY_MUX_CTRL1_LANE0_SRC_SFEN2 (2 << 12)
>> +#define MIPI_PHY_MUX_CTRL1_LANE0_SRC_SFEN3 (3 << 12)
>> +
>> +/* C3 CSI-2 HOST register */
>> +#define CSI2_HOST_N_LANES CSI2_REG_H(0x04)
>> +#define CSI2_HOST_N_LANES_MASK GENMASK(1, 0)
>> +#define CSI2_HOST_N_LANES_1 (0 << 0)
>> +#define CSI2_HOST_N_LANES_2 BIT(0)
>> +#define CSI2_HOST_N_LANES_3 (2 << 0)
>> +#define CSI2_HOST_N_LANES_4 (3 << 0)
>> +
>> +#define CSI2_HOST_CSI2_RESETN CSI2_REG_H(0x10)
>> +#define CSI2_HOST_CSI2_RESETN_MASK BIT(0)
>> +#define CSI2_HOST_CSI2_RESETN_ACTIVE (0 << 0)
>> +#define CSI2_HOST_CSI2_RESETN_EXIT BIT(0)
>> +
>> +#define C3_MIPI_CSI2_MAX_WIDTH 2888
>> +#define C3_MIPI_CSI2_MIN_WIDTH 160
>> +#define C3_MIPI_CSI2_MAX_HEIGHT 2240
>> +#define C3_MIPI_CSI2_MIN_HEIGHT 120
>> +#define C3_MIPI_CSI2_DEFAULT_WIDTH 1920
>> +#define C3_MIPI_CSI2_DEFAULT_HEIGHT 1080
>> +#define C3_MIPI_CSI2_DEFAULT_FMT MEDIA_BUS_FMT_SRGGB10_1X10
>> +
>> +/* C3 CSI-2 pad list */
>> +enum {
>> + C3_MIPI_CSI2_PAD_SINK,
>> + C3_MIPI_CSI2_PAD_SRC,
>> + C3_MIPI_CSI2_PAD_MAX
>> +};
>> +
>> +/*
>> + * struct c3_csi_info - MIPI CSI2 information
>> + *
>> + * @clocks: array of MIPI CSI2 clock names
>> + * @clock_num: actual clock number
>> + */
>> +struct c3_csi_info {
>> + char *clocks[MIPI_CSI2_CLOCK_NUM_MAX];
>> + u32 clock_num;
>> +};
>> +
>> +/*
>> + * struct c3_csi_device - MIPI CSI2 platform device
>> + *
>> + * @dev: pointer to the struct device
>> + * @aphy: MIPI CSI2 aphy register address
>> + * @dphy: MIPI CSI2 dphy register address
>> + * @host: MIPI CSI2 host register address
>> + * @clks: array of MIPI CSI2 clocks
>> + * @sd: MIPI CSI2 sub-device
>> + * @pads: MIPI CSI2 sub-device pads
>> + * @notifier: notifier to register on the v4l2-async API
>> + * @src_pad: source sub-device pad
>> + * @bus: MIPI CSI2 bus information
>> + * @info: version-specific MIPI CSI2 information
>> + */
>> +struct c3_csi_device {
>> + struct device *dev;
>> + void __iomem *aphy;
>> + void __iomem *dphy;
>> + void __iomem *host;
>> + struct clk_bulk_data clks[MIPI_CSI2_CLOCK_NUM_MAX];
>> +
>> + struct v4l2_subdev sd;
>> + struct media_pad pads[C3_MIPI_CSI2_PAD_MAX];
>> + struct v4l2_async_notifier notifier;
>> + struct media_pad *src_pad;
>> + struct v4l2_mbus_config_mipi_csi2 bus;
>> +
>> + const struct c3_csi_info *info;
>> +};
>> +
>> +static const u32 c3_mipi_csi_formats[] = {
>> + MEDIA_BUS_FMT_SBGGR10_1X10,
>> + MEDIA_BUS_FMT_SGBRG10_1X10,
>> + MEDIA_BUS_FMT_SGRBG10_1X10,
>> + MEDIA_BUS_FMT_SRGGB10_1X10,
>> + MEDIA_BUS_FMT_SBGGR12_1X12,
>> + MEDIA_BUS_FMT_SGBRG12_1X12,
>> + MEDIA_BUS_FMT_SGRBG12_1X12,
>> + MEDIA_BUS_FMT_SRGGB12_1X12,
>> +};
>> +
>> +/* Hardware configuration */
>> +
>> +static void c3_mipi_csi_write(struct c3_csi_device *csi, u32 reg, u32 val)
>> +{
>> + void __iomem *addr;
>> +
>> + switch (CSI2_SUBMD(reg)) {
>> + case SUBMD_APHY:
>> + addr = csi->aphy + CSI2_REG_ADDR(reg);
>> + break;
>> + case SUBMD_DPHY:
>> + addr = csi->dphy + CSI2_REG_ADDR(reg);
>> + break;
>> + case SUBMD_HOST:
>> + addr = csi->host + CSI2_REG_ADDR(reg);
>> + break;
>> + default:
>> + dev_err(csi->dev, "Invalid sub-module: %lu\n", CSI2_SUBMD(reg));
>> + return;
>> + }
>> +
>> + writel(val, addr);
>> +}
>> +
>> +static void c3_mipi_csi_cfg_aphy(struct c3_csi_device *csi)
>> +{
>> + c3_mipi_csi_write(csi, CSI_PHY_CNTL0,
>> + CSI_PHY_CNTL0_HS_LP_BIAS_EN |
>> + CSI_PHY_CNTL0_HS_RX_TRIM_11 |
>> + CSI_PHY_CNTL0_LP_LOW_VTH_2 |
>> + CSI_PHY_CNTL0_LP_HIGH_VTH_4 |
>> + CSI_PHY_CNTL0_DATA_LANE0_HS_DIG_EN |
>> + CSI_PHY_CNTL0_DATA_LANE1_HS_DIG_EN |
>> + CSI_PHY_CNTL0_CLK0_LANE_HS_DIG_EN |
>> + CSI_PHY_CNTL0_DATA_LANE2_HS_DIG_EN |
>> + CSI_PHY_CNTL0_DATA_LANE3_HS_DIG_EN);
>> +
>> + c3_mipi_csi_write(csi, CSI_PHY_CNTL1,
>> + CSI_PHY_CNTL1_HS_EQ_CAP_SMALL |
>> + CSI_PHY_CNTL1_HS_EQ_RES_MED |
>> + CSI_PHY_CNTL1_CLK_CHN_EQ_MAX_GAIN |
>> + CSI_PHY_CNTL1_DATA_CHN_EQ_MAX_GAIN |
>> + CSI_PHY_CNTL1_COM_BG_EN |
>> + CSI_PHY_CNTL1_HS_SYNC_EN);
>> +}
>> +
>> +static void c3_mipi_csi_cfg_dphy(struct c3_csi_device *csi, s64 rate)
>> +{
>> + u32 val;
>> + u32 settle;
>> +
>> + /* Calculate the high speed settle */
>> + val = DIV_ROUND_UP(1000000000, rate);
>> + settle = (16 * val + 230) / 10;
>> +
>> + c3_mipi_csi_write(csi, MIPI_PHY_CLK_LANE_CTRL,
>> + MIPI_PHY_CLK_LANE_CTRL_HS_RX_EN |
>> + MIPI_PHY_CLK_LANE_CTRL_END_EN |
>> + MIPI_PHY_CLK_LANE_CTRL_LPEN_DIS |
>> + MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_EN |
>> + MIPI_PHY_CLK_LANE_CTRL_TCLK_ZERO_HS_8);
>> +
>> + c3_mipi_csi_write(csi, MIPI_PHY_TCLK_MISS, MIPI_PHY_TCLK_MISS_CYCLES_9);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TCLK_SETTLE,
>> + MIPI_PHY_TCLK_SETTLE_CYCLES_31);
>> + c3_mipi_csi_write(csi, MIPI_PHY_THS_EXIT, MIPI_PHY_THS_EXIT_CYCLES_8);
>> + c3_mipi_csi_write(csi, MIPI_PHY_THS_SKIP, MIPI_PHY_THS_SKIP_CYCLES_10);
>> + c3_mipi_csi_write(csi, MIPI_PHY_THS_SETTLE, settle);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TINIT, MIPI_PHY_TINIT_CYCLES_20000);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TMBIAS, MIPI_PHY_TMBIAS_CYCLES_256);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TULPS_C, MIPI_PHY_TULPS_C_CYCLES_4096);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TULPS_S, MIPI_PHY_TULPS_S_CYCLES_256);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TLP_EN_W, MIPI_PHY_TLP_EN_W_CYCLES_12);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TLPOK, MIPI_PHY_TLPOK_CYCLES_256);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TWD_INIT,
>> + MIPI_PHY_TWD_INIT_DOG_0X400000);
>> + c3_mipi_csi_write(csi, MIPI_PHY_TWD_HS, MIPI_PHY_TWD_HS_DOG_0X400000);
>> +
>> + c3_mipi_csi_write(csi, MIPI_PHY_DATA_LANE_CTRL1,
>> + MIPI_PHY_DATA_LANE_CTRL1_INSERT_ERRESC |
>> + MIPI_PHY_DATA_LANE_CTRL1_HS_SYNC_CHK_EN |
>> + MIPI_PHY_DATA_LANE_CTRL1_PIPE_ALL_EN |
>> + MIPI_PHY_DATA_LANE_CTRL1_PIPE_DELAY_3);
>> +
>> + /* Set the order of lanes */
>> + c3_mipi_csi_write(csi, MIPI_PHY_MUX_CTRL0,
>> + MIPI_PHY_MUX_CTRL0_SFEN3_SRC_LANE3 |
>> + MIPI_PHY_MUX_CTRL0_SFEN2_SRC_LANE2 |
>> + MIPI_PHY_MUX_CTRL0_SFEN1_SRC_LANE1 |
>> + MIPI_PHY_MUX_CTRL0_SFEN0_SRC_LANE0);
>> +
>> + c3_mipi_csi_write(csi, MIPI_PHY_MUX_CTRL1,
>> + MIPI_PHY_MUX_CTRL1_LANE3_SRC_SFEN3 |
>> + MIPI_PHY_MUX_CTRL1_LANE2_SRC_SFEN2 |
>> + MIPI_PHY_MUX_CTRL1_LANE1_SRC_SFEN1 |
>> + MIPI_PHY_MUX_CTRL1_LANE0_SRC_SFEN0);
>> +
>> + /* Enable digital data and clock lanes */
>> + c3_mipi_csi_write(csi, MIPI_PHY_CTRL,
>> + MIPI_PHY_CTRL_DATA_LANE0_EN |
>> + MIPI_PHY_CTRL_DATA_LANE1_EN |
>> + MIPI_PHY_CTRL_DATA_LANE2_EN |
>> + MIPI_PHY_CTRL_DATA_LANE3_EN |
>> + MIPI_PHY_CTRL_CLOCK_LANE_EN);
>> +}
>> +
>> +static void c3_mipi_csi_cfg_host(struct c3_csi_device *csi)
>> +{
>> + /* Reset CSI-2 controller output */
>> + c3_mipi_csi_write(csi, CSI2_HOST_CSI2_RESETN,
>> + CSI2_HOST_CSI2_RESETN_ACTIVE);
>> + c3_mipi_csi_write(csi, CSI2_HOST_CSI2_RESETN,
>> + CSI2_HOST_CSI2_RESETN_EXIT);
>> +
>> + /* Set data lane number */
>> + c3_mipi_csi_write(csi, CSI2_HOST_N_LANES, csi->bus.num_data_lanes - 1);
>> +}
>> +
>> +static int c3_mipi_csi_start_stream(struct c3_csi_device *csi,
>> + struct v4l2_subdev *src_sd)
>> +{
>> + s64 link_freq;
>> + s64 lane_rate;
>> +
>> + link_freq = v4l2_get_link_freq(src_sd->ctrl_handler, 0, 0);
>> + if (link_freq < 0) {
>> + dev_err(csi->dev,
>> + "Unable to obtain link frequency: %lld\n", link_freq);
>> + return link_freq;
>> + }
>> +
>> + lane_rate = link_freq * 2;
>> + if (lane_rate > 1500000000) {
>> + dev_err(csi->dev, "Invalid lane rate: %lld\n", lane_rate);
>> + return -EINVAL;
>> + }
>> +
>> + c3_mipi_csi_cfg_aphy(csi);
>> + c3_mipi_csi_cfg_dphy(csi, lane_rate);
>> + c3_mipi_csi_cfg_host(csi);
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_enable_streams(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_state *state,
>> + u32 pad, u64 streams_mask)
>> +{
>> + struct c3_csi_device *csi = v4l2_get_subdevdata(sd);
>> + struct media_pad *sink_pad;
>> + struct v4l2_subdev *src_sd;
>> + int ret;
>> +
>> + sink_pad = &csi->pads[C3_MIPI_CSI2_PAD_SINK];
>> + csi->src_pad = media_pad_remote_pad_unique(sink_pad);
>> + if (IS_ERR(csi->src_pad)) {
>> + dev_dbg(csi->dev, "Failed to get source pad for MIPI CSI-2\n");
>> + return -EPIPE;
>> + }
>> +
>> + src_sd = media_entity_to_v4l2_subdev(csi->src_pad->entity);
>> +
>> + pm_runtime_resume_and_get(csi->dev);
>> +
>> + c3_mipi_csi_start_stream(csi, src_sd);
>> +
>> + ret = v4l2_subdev_enable_streams(src_sd, csi->src_pad->index, BIT(0));
>> + if (ret) {
>> + pm_runtime_put(csi->dev);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_disable_streams(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_state *state,
>> + u32 pad, u64 streams_mask)
>> +{
>> + struct c3_csi_device *csi = v4l2_get_subdevdata(sd);
>> + struct v4l2_subdev *src_sd;
>> +
>> + if (csi->src_pad) {
>> + src_sd = media_entity_to_v4l2_subdev(csi->src_pad->entity);
>> + v4l2_subdev_disable_streams(src_sd, csi->src_pad->index,
>> + BIT(0));
>> + }
>> + csi->src_pad = NULL;
>> +
>> + pm_runtime_put(csi->dev);
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_enum_mbus_code(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_state *state,
>> + struct v4l2_subdev_mbus_code_enum *code)
>> +{
>> + switch (code->pad) {
>> + case C3_MIPI_CSI2_PAD_SINK:
>> + if (code->index >= ARRAY_SIZE(c3_mipi_csi_formats))
>> + return -EINVAL;
>> +
>> + code->code = c3_mipi_csi_formats[code->index];
>> + break;
>> + case C3_MIPI_CSI2_PAD_SRC:
>> + struct v4l2_mbus_framefmt *fmt;
> I had missed this. You probably want to limit the scope of *fmt with
>
> case C3_MIPI_CSI2_PAD_SRC: {
> struct v4l2_mbus_framefmt *fmt;
>
> ...
> }
>
> Or declare it at the beginning of the function.
>
> This issue was reported by the CI loop in the 'static upstream' job
> https://gitlab.freedesktop.org/linux-media/users/jmondi/-/jobs/69823161/raw
>
> drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c:478:17: error: typename in expression
> drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c:478:24: error: Expected ; at end of statement
> drivers/media/platform/amlogic/c3/mipi-csi2/c3-mipi-csi2.c:478:24: error: got v4l2_mbus_framefmt
>
> A similar (identical) issue has been flagged in the adapt driver (and
> it's possibily present in other drivers of this set as well, please
> check)
>
Will check this issue.
>> +
>> + if (code->index)
>> + return -EINVAL;
>> +
>> + fmt = v4l2_subdev_state_get_format(state, code->pad);
>> + code->code = fmt->code;
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_set_fmt(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_state *state,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct v4l2_mbus_framefmt *fmt;
>> + unsigned int i;
>> +
>> + if (format->pad != C3_MIPI_CSI2_PAD_SINK)
>> + return v4l2_subdev_get_fmt(sd, state, format);
>> +
>> + fmt = v4l2_subdev_state_get_format(state, format->pad);
>> +
>> + for (i = 0; i < ARRAY_SIZE(c3_mipi_csi_formats); i++) {
>> + if (format->format.code == c3_mipi_csi_formats[i]) {
>> + fmt->code = c3_mipi_csi_formats[i];
>> + break;
>> + }
>> + }
>> +
>> + if (i == ARRAY_SIZE(c3_mipi_csi_formats))
>> + fmt->code = c3_mipi_csi_formats[0];
>> +
>> + fmt->width = clamp_t(u32, format->format.width,
>> + C3_MIPI_CSI2_MIN_WIDTH, C3_MIPI_CSI2_MAX_WIDTH);
>> + fmt->height = clamp_t(u32, format->format.height,
>> + C3_MIPI_CSI2_MIN_HEIGHT, C3_MIPI_CSI2_MAX_HEIGHT);
>> + fmt->colorspace = V4L2_COLORSPACE_RAW;
>> + fmt->xfer_func = V4L2_XFER_FUNC_NONE;
>> + fmt->ycbcr_enc = V4L2_YCBCR_ENC_601;
>> + fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> +
>> + format->format = *fmt;
>> +
>> + /* Synchronize the format to source pad */
>> + fmt = v4l2_subdev_state_get_format(state, C3_MIPI_CSI2_PAD_SRC);
>> + *fmt = format->format;
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_init_state(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_state *state)
>> +{
>> + struct v4l2_mbus_framefmt *sink_fmt;
>> + struct v4l2_mbus_framefmt *src_fmt;
>> +
>> + sink_fmt = v4l2_subdev_state_get_format(state, C3_MIPI_CSI2_PAD_SINK);
>> + src_fmt = v4l2_subdev_state_get_format(state, C3_MIPI_CSI2_PAD_SRC);
>> +
>> + sink_fmt->width = C3_MIPI_CSI2_DEFAULT_WIDTH;
>> + sink_fmt->height = C3_MIPI_CSI2_DEFAULT_HEIGHT;
>> + sink_fmt->field = V4L2_FIELD_NONE;
>> + sink_fmt->code = C3_MIPI_CSI2_DEFAULT_FMT;
>> + sink_fmt->colorspace = V4L2_COLORSPACE_RAW;
>> + sink_fmt->xfer_func = V4L2_XFER_FUNC_NONE;
>> + sink_fmt->ycbcr_enc = V4L2_YCBCR_ENC_601;
>> + sink_fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> +
>> + *src_fmt = *sink_fmt;
>> +
>> + return 0;
>> +}
>> +
>> +static const struct v4l2_subdev_pad_ops c3_mipi_csi_pad_ops = {
>> + .enum_mbus_code = c3_mipi_csi_enum_mbus_code,
>> + .get_fmt = v4l2_subdev_get_fmt,
>> + .set_fmt = c3_mipi_csi_set_fmt,
>> + .enable_streams = c3_mipi_csi_enable_streams,
>> + .disable_streams = c3_mipi_csi_disable_streams,
>> +};
>> +
>> +static const struct v4l2_subdev_ops c3_mipi_csi_subdev_ops = {
>> + .pad = &c3_mipi_csi_pad_ops,
>> +};
>> +
>> +static const struct v4l2_subdev_internal_ops c3_mipi_csi_internal_ops = {
>> + .init_state = c3_mipi_csi_init_state,
>> +};
>> +
>> +/* Media entity operations */
>> +static const struct media_entity_operations c3_mipi_csi_entity_ops = {
>> + .link_validate = v4l2_subdev_link_validate,
>> +};
>> +
>> +/* PM runtime */
>> +
>> +static int c3_mipi_csi_runtime_suspend(struct device *dev)
>> +{
>> + struct c3_csi_device *csi = dev_get_drvdata(dev);
>> +
>> + clk_bulk_disable_unprepare(csi->info->clock_num, csi->clks);
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_runtime_resume(struct device *dev)
>> +{
>> + struct c3_csi_device *csi = dev_get_drvdata(dev);
>> +
>> + return clk_bulk_prepare_enable(csi->info->clock_num, csi->clks);
>> +}
>> +
>> +static const struct dev_pm_ops c3_mipi_csi_pm_ops = {
>> + SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
>> + pm_runtime_force_resume)
>> + RUNTIME_PM_OPS(c3_mipi_csi_runtime_suspend,
>> + c3_mipi_csi_runtime_resume, NULL)
>> +};
>> +
>> +/* Probe/remove & platform driver */
>> +
>> +static int c3_mipi_csi_subdev_init(struct c3_csi_device *csi)
>> +{
>> + struct v4l2_subdev *sd = &csi->sd;
>> + int ret;
>> +
>> + v4l2_subdev_init(sd, &c3_mipi_csi_subdev_ops);
>> + sd->owner = THIS_MODULE;
>> + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
>> + sd->internal_ops = &c3_mipi_csi_internal_ops;
>> + snprintf(sd->name, sizeof(sd->name), "%s", MIPI_CSI2_SUBDEV_NAME);
>> +
>> + sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
>> + sd->entity.ops = &c3_mipi_csi_entity_ops;
>> +
>> + sd->dev = csi->dev;
>> + v4l2_set_subdevdata(sd, csi);
>> +
>> + csi->pads[C3_MIPI_CSI2_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
>> + csi->pads[C3_MIPI_CSI2_PAD_SRC].flags = MEDIA_PAD_FL_SOURCE;
>> + ret = media_entity_pads_init(&sd->entity, C3_MIPI_CSI2_PAD_MAX,
>> + csi->pads);
>> + if (ret)
>> + return ret;
>> +
>> + ret = v4l2_subdev_init_finalize(sd);
>> + if (ret) {
>> + media_entity_cleanup(&sd->entity);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void c3_mipi_csi_subdev_deinit(struct c3_csi_device *csi)
>> +{
>> + v4l2_subdev_cleanup(&csi->sd);
>> + media_entity_cleanup(&csi->sd.entity);
>> +}
>> +
>> +/* Subdev notifier register */
>> +static int c3_mipi_csi_notify_bound(struct v4l2_async_notifier *notifier,
>> + struct v4l2_subdev *sd,
>> + struct v4l2_async_connection *asc)
>> +{
>> + struct c3_csi_device *csi = v4l2_get_subdevdata(notifier->sd);
>> + struct media_pad *sink = &csi->sd.entity.pads[C3_MIPI_CSI2_PAD_SINK];
>> +
>> + return v4l2_create_fwnode_links_to_pad(sd, sink, MEDIA_LNK_FL_ENABLED |
>> + MEDIA_LNK_FL_IMMUTABLE);
>> +}
>> +
>> +static const struct v4l2_async_notifier_operations c3_mipi_csi_notify_ops = {
>> + .bound = c3_mipi_csi_notify_bound,
>> +};
>> +
>> +static int c3_mipi_csi_async_register(struct c3_csi_device *csi)
>> +{
>> + struct v4l2_fwnode_endpoint vep = {
>> + .bus_type = V4L2_MBUS_CSI2_DPHY,
>> + };
>> + struct v4l2_async_connection *asc;
>> + struct fwnode_handle *ep;
>> + int ret;
>> +
>> + v4l2_async_subdev_nf_init(&csi->notifier, &csi->sd);
>> +
>> + ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(csi->dev), 0, 0,
>> + FWNODE_GRAPH_ENDPOINT_NEXT);
>> + if (!ep)
>> + return -ENOTCONN;
>> +
>> + ret = v4l2_fwnode_endpoint_parse(ep, &vep);
>> + if (ret)
>> + goto err_put_handle;
>> +
>> + csi->bus = vep.bus.mipi_csi2;
>> + if (csi->bus.num_data_lanes < 1 || csi->bus.num_data_lanes > 4) {
>> + dev_err(csi->dev, "Unsupported data lanes number\n");
>> + goto err_put_handle;
> Flagged by CI as well, 'ret' is not initialized before being returned.
> Please check other drivers as well for this common pattern.
Will check this issue.
>
> Thanks
> j
>
>> + }
>> +
>> + asc = v4l2_async_nf_add_fwnode_remote(&csi->notifier, ep,
>> + struct v4l2_async_connection);
>> + if (IS_ERR(asc)) {
>> + ret = PTR_ERR(asc);
>> + goto err_put_handle;
>> + }
>> +
>> + csi->notifier.ops = &c3_mipi_csi_notify_ops;
>> + ret = v4l2_async_nf_register(&csi->notifier);
>> + if (ret)
>> + goto err_cleanup_nf;
>> +
>> + ret = v4l2_async_register_subdev(&csi->sd);
>> + if (ret)
>> + goto err_unregister_nf;
>> +
>> + fwnode_handle_put(ep);
>> +
>> + return 0;
>> +
>> +err_unregister_nf:
>> + v4l2_async_nf_unregister(&csi->notifier);
>> +err_cleanup_nf:
>> + v4l2_async_nf_cleanup(&csi->notifier);
>> +err_put_handle:
>> + fwnode_handle_put(ep);
>> + return ret;
>> +}
>> +
>> +static void c3_mipi_csi_async_unregister(struct c3_csi_device *csi)
>> +{
>> + v4l2_async_unregister_subdev(&csi->sd);
>> + v4l2_async_nf_unregister(&csi->notifier);
>> + v4l2_async_nf_cleanup(&csi->notifier);
>> +}
>> +
>> +static int c3_mipi_csi_ioremap_resource(struct c3_csi_device *csi)
>> +{
>> + struct device *dev = csi->dev;
>> + struct platform_device *pdev = to_platform_device(dev);
>> +
>> + csi->aphy = devm_platform_ioremap_resource_byname(pdev, "aphy");
>> + if (IS_ERR(csi->aphy))
>> + return PTR_ERR(csi->aphy);
>> +
>> + csi->dphy = devm_platform_ioremap_resource_byname(pdev, "dphy");
>> + if (IS_ERR(csi->dphy))
>> + return PTR_ERR(csi->dphy);
>> +
>> + csi->host = devm_platform_ioremap_resource_byname(pdev, "host");
>> + if (IS_ERR(csi->host))
>> + return PTR_ERR(csi->host);
>> +
>> + return 0;
>> +}
>> +
>> +static int c3_mipi_csi_get_clocks(struct c3_csi_device *csi)
>> +{
>> + const struct c3_csi_info *info = csi->info;
>> +
>> + for (unsigned int i = 0; i < info->clock_num; i++)
>> + csi->clks[i].id = info->clocks[i];
>> +
>> + return devm_clk_bulk_get(csi->dev, info->clock_num, csi->clks);
>> +}
>> +
>> +static int c3_mipi_csi_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct c3_csi_device *csi;
>> + int ret;
>> +
>> + csi = devm_kzalloc(dev, sizeof(*csi), GFP_KERNEL);
>> + if (!csi)
>> + return -ENOMEM;
>> +
>> + csi->info = of_device_get_match_data(dev);
>> + csi->dev = dev;
>> +
>> + ret = c3_mipi_csi_ioremap_resource(csi);
>> + if (ret)
>> + return dev_err_probe(dev, ret, "Failed to ioremap resource\n");
>> +
>> + ret = c3_mipi_csi_get_clocks(csi);
>> + if (ret)
>> + return dev_err_probe(dev, ret, "Failed to get clocks\n");
>> +
>> + platform_set_drvdata(pdev, csi);
>> +
>> + pm_runtime_enable(dev);
>> +
>> + ret = c3_mipi_csi_subdev_init(csi);
>> + if (ret)
>> + goto err_disable_runtime_pm;
>> +
>> + ret = c3_mipi_csi_async_register(csi);
>> + if (ret)
>> + goto err_deinit_subdev;
>> +
>> + return 0;
>> +
>> +err_deinit_subdev:
>> + c3_mipi_csi_subdev_deinit(csi);
>> +err_disable_runtime_pm:
>> + pm_runtime_disable(dev);
>> + return ret;
>> +};
>> +
>> +static void c3_mipi_csi_remove(struct platform_device *pdev)
>> +{
>> + struct c3_csi_device *csi = platform_get_drvdata(pdev);
>> +
>> + c3_mipi_csi_async_unregister(csi);
>> + c3_mipi_csi_subdev_deinit(csi);
>> +
>> + pm_runtime_disable(&pdev->dev);
>> +};
>> +
>> +static const struct c3_csi_info c3_mipi_csi_info = {
>> + .clocks = {"vapb", "phy0"},
>> + .clock_num = 2
>> +};
>> +
>> +static const struct of_device_id c3_mipi_csi_of_match[] = {
>> + {
>> + .compatible = "amlogic,c3-mipi-csi2",
>> + .data = &c3_mipi_csi_info,
>> + },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, c3_mipi_csi_of_match);
>> +
>> +static struct platform_driver c3_mipi_csi_driver = {
>> + .probe = c3_mipi_csi_probe,
>> + .remove = c3_mipi_csi_remove,
>> + .driver = {
>> + .name = "c3-mipi-csi2",
>> + .of_match_table = c3_mipi_csi_of_match,
>> + .pm = pm_ptr(&c3_mipi_csi_pm_ops),
>> + },
>> +};
>> +
>> +module_platform_driver(c3_mipi_csi_driver);
>> +
>> +MODULE_AUTHOR("Keke Li <keke.li@...ogic.com>");
>> +MODULE_DESCRIPTION("Amlogic C3 MIPI CSI-2 receiver");
>> +MODULE_LICENSE("GPL");
>>
>> --
>> 2.47.1
>>
>>
>>
Powered by blists - more mailing lists