| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1b98265e-8766-4504-b374-f7af8203c926@quicinc.com>
Date: Thu, 6 Feb 2025 12:41:30 -0800
From: Abhinav Kumar <quic_abhinavk@...cinc.com>
To: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
CC: Andrzej Hajda <andrzej.hajda@...el.com>,
Neil Armstrong
<neil.armstrong@...aro.org>,
Robert Foss <rfoss@...nel.org>,
Laurent Pinchart
<Laurent.pinchart@...asonboard.com>,
Jonas Karlman <jonas@...boo.se>,
Jernej
Skrabec <jernej.skrabec@...il.com>,
Maarten Lankhorst
<maarten.lankhorst@...ux.intel.com>,
Maxime Ripard <mripard@...nel.org>,
Thomas Zimmermann <tzimmermann@...e.de>,
David Airlie <airlied@...il.com>, Rob Clark <robdclark@...il.com>,
Sean Paul <sean@...rly.run>,
Marijn Suijten
<marijn.suijten@...ainline.org>,
Simona Vetter <simona@...ll.ch>,
Simona
Vetter <simona.vetter@...ll.ch>,
<dri-devel@...ts.freedesktop.org>, <linux-arm-msm@...r.kernel.org>,
<freedreno@...ts.freedesktop.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v6 2/7] drm/msm/hdmi: program HDMI timings during
atomic_pre_enable
On 2/3/2025 4:59 PM, Dmitry Baryshkov wrote:
> On Mon, Feb 03, 2025 at 11:34:00AM -0800, Abhinav Kumar wrote:
>>
>>
>> On 1/24/2025 1:47 PM, Dmitry Baryshkov wrote:
>>> The mode_set callback is deprecated, it doesn't get the
>>> drm_bridge_state, just mode-related argumetns. Also Abhinav pointed out
>>> that HDMI timings should be programmed after setting up HDMI PHY and
>>> PLL. Rework the code to program HDMI timings at the end of
>>> atomic_pre_enable().
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
>>> ---
>>> drivers/gpu/drm/msm/hdmi/hdmi_bridge.c | 23 +++++++++++++++--------
>>> 1 file changed, 15 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c b/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c
>>> index d839c71091dcdc3b020fcbba8d698d58ee7fc749..d5ab1f74c0e6f47dc59872c016104e9a84d85e9e 100644
>>> --- a/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c
>>> +++ b/drivers/gpu/drm/msm/hdmi/hdmi_bridge.c
>>> @@ -126,15 +126,26 @@ static void msm_hdmi_config_avi_infoframe(struct hdmi *hdmi)
>>> hdmi_write(hdmi, REG_HDMI_INFOFRAME_CTRL1, val);
>>> }
>>> +static void msm_hdmi_bridge_atomic_set_timings(struct hdmi *hdmi,
>>> + const struct drm_display_mode *mode);
>>> static void msm_hdmi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
>>> struct drm_bridge_state *old_bridge_state)
>>> {
>>> + struct drm_atomic_state *state = old_bridge_state->base.state;
>>> struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
>>> struct hdmi *hdmi = hdmi_bridge->hdmi;
>>> struct hdmi_phy *phy = hdmi->phy;
>>> + struct drm_encoder *encoder = bridge->encoder;
>>> + struct drm_connector *connector;
>>> + struct drm_connector_state *conn_state;
>>> + struct drm_crtc_state *crtc_state;
>>> DBG("power up");
>>> + connector = drm_atomic_get_new_connector_for_encoder(state, encoder);
>>> + conn_state = drm_atomic_get_new_connector_state(state, connector);
>>> + crtc_state = drm_atomic_get_new_crtc_state(state, conn_state->crtc);
>>> +
>>> if (!hdmi->power_on) {
>>> msm_hdmi_phy_resource_enable(phy);
>>> msm_hdmi_power_on(bridge);
>>> @@ -151,6 +162,8 @@ static void msm_hdmi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
>>> if (hdmi->hdcp_ctrl)
>>> msm_hdmi_hdcp_on(hdmi->hdcp_ctrl);
>>> +
>>> + msm_hdmi_bridge_atomic_set_timings(hdmi, &crtc_state->adjusted_mode);
>>> }
>>
>> This addresses my comment about setting up the HDMI timing registers before
>> setting up the timing engine registers.
>>
>> But prior to this change, mode_set was doing the same thing as
>> msm_hdmi_bridge_atomic_set_timings() which means
>> msm_hdmi_bridge_atomic_set_timings() should be called at the beginning of
>> pre_enable()?
>>
>> The controller is enabled in msm_hdmi_set_mode(). So this should be done
>> before that.
>
> In [1] you provided the following order:
>
> 1) setup HDMI PHY and PLL
> 2) setup HDMI video path correctly (HDMI timing registers)
> 3) setup timing generator to match the HDMI video in (2)
> 4) Enable timing engine
>
> This means htat msm_hdmi_bridge_atomic_set_timings() should come at the
> end of msm_hdmi_bridge_atomic_pre_enable(), not in the beginning /
> middle of it.
>
> [1] https://lore.kernel.org/dri-devel/8dd4a43e-d83c-1f36-21ff-61e13ff751e7@quicinc.com/
>
Sequence given is correct and is exactly what is given in the docs. What
is somewhat not clear in the docs is the location of the enable of the
HDMI controller. This is not there in the above 4 steps. I am referring
to the enable bit being programmed in msm_hdmi_set_mode(). Ideally till
we enable the timing engine, it should be okay but what I wanted to do
was to keep the msm_hdmi_set_mode() as the last call in this function
that way we program everything and then enable the controller.
This can be done in either way, move it to the beginning of the function
or move it right before msm_hdmi_set_mode(). I had suggested beginning
because thats how it was when things were still in mode_set.
>
>>
>>> static void msm_hdmi_bridge_atomic_post_disable(struct drm_bridge *bridge,
>>> @@ -177,17 +190,12 @@ static void msm_hdmi_bridge_atomic_post_disable(struct drm_bridge *bridge,
>>> }
>>> }
>>> -static void msm_hdmi_bridge_mode_set(struct drm_bridge *bridge,
>>> - const struct drm_display_mode *mode,
>>> - const struct drm_display_mode *adjusted_mode)
>>> +static void msm_hdmi_bridge_atomic_set_timings(struct hdmi *hdmi,
>>> + const struct drm_display_mode *mode)
>>> {
>>> - struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
>>> - struct hdmi *hdmi = hdmi_bridge->hdmi;
>>> int hstart, hend, vstart, vend;
>>> uint32_t frame_ctrl;
>>> - mode = adjusted_mode;
>>> -
>>> hdmi->pixclock = mode->clock * 1000;
>>> hstart = mode->htotal - mode->hsync_start;
>>> @@ -306,7 +314,6 @@ static const struct drm_bridge_funcs msm_hdmi_bridge_funcs = {
>>> .atomic_reset = drm_atomic_helper_bridge_reset,
>>> .atomic_pre_enable = msm_hdmi_bridge_atomic_pre_enable,
>>> .atomic_post_disable = msm_hdmi_bridge_atomic_post_disable,
>>> - .mode_set = msm_hdmi_bridge_mode_set,
>>> .mode_valid = msm_hdmi_bridge_mode_valid,
>>> .edid_read = msm_hdmi_bridge_edid_read,
>>> .detect = msm_hdmi_bridge_detect,
>>>
>
Powered by blists - more mailing lists