linux-kernel - [PATCH 2/3] leds: leds-st1202: spacing and proofreading editing

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID:
 <CWLP123MB547333EFFFBFFA840225BC02C5C22@CWLP123MB5473.GBRP123.PROD.OUTLOOK.COM>
Date: Wed, 26 Feb 2025 17:08:44 +0000
From: Manuel Fombuena <fombuena@...look.com>
To: pavel@....cz,
	lee@...nel.org,
	linux-leds@...r.kernel.org,
	linux-kernel@...r.kernel.org
Subject: [PATCH 2/3] leds: leds-st1202: spacing and proofreading editing

Minor edits regarding use of spacing and proofreading.

There is a minor inconsistency in the use of spacing as margin in
one of the comments providing details about the datasheet.

There is also a typo that comes from the datasheet itself.

Change spacing on comment and correct typo.

Signed-off-by: Manuel Fombuena <fombuena@...look.com>
---
 drivers/leds/leds-st1202.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/leds/leds-st1202.c b/drivers/leds/leds-st1202.c
index e7dce8c26bde..4e5dd76d714d 100644
--- a/drivers/leds/leds-st1202.c
+++ b/drivers/leds/leds-st1202.c
@@ -99,9 +99,9 @@ static int st1202_pwm_pattern_write(struct st1202_chip *chip, int led_num,
 	value_h = (u8)(value >> 8);
 
 	/*
-	 *  Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
-	 *  where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
-	 *  and y is the pattern number in hexadecimal (y = 00h .. 07h)
+	 * Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
+	 * where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
+	 * and y is the pattern number in hexadecimal (y = 00h .. 07h)
 	 */
 	ret = st1202_write_reg(chip, (ST1202_PATTERN_PWM + (led_num * 2) + 0x18 * pattern),
 				value_l);
@@ -287,8 +287,8 @@ static int st1202_setup(struct st1202_chip *chip)
 	guard(mutex)(&chip->lock);
 
 	/*
-	 * Once the supply voltage is applied, the LED1202 executes some internal checks,
-	 * afterwords it stops the oscillator and puts the internal LDO in quiescent mode.
+	 * Once the supply voltage is applied, the LED1202 executes some internal checks.
+	 * Afterwards, it stops the oscillator and puts the internal LDO in quiescent mode.
 	 * To start the device, EN bit must be set inside the “Device Enable” register at
 	 * address 01h. As soon as EN is set, the LED1202 loads the adjustment parameters
 	 * from the internal non-volatile memory and performs an auto-calibration procedure
-- 
2.48.1