linux-kernel - Re: [PATCH] serial: msm: Configure correct working mode before starting earlycon

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <d8a0f3a2-03ed-48be-8ca2-dfed622554ee@linaro.org>
Date: Wed, 9 Apr 2025 14:37:35 +0200
From: neil.armstrong@...aro.org
To: Stephan Gerhold <stephan.gerhold@...aro.org>,
 Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
 Jiri Slaby <jirislaby@...nel.org>
Cc: Stephen Boyd <sboyd@...nel.org>, linux-arm-msm@...r.kernel.org,
 linux-kernel@...r.kernel.org, linux-serial@...r.kernel.org,
 Sam Day <me@...cday.com>
Subject: Re: [PATCH] serial: msm: Configure correct working mode before
 starting earlycon

On 08/04/2025 19:22, Stephan Gerhold wrote:
> The MSM UART DM controller supports different working modes, e.g. DMA or
> the "single-character mode", where all reads/writes operate on a single
> character rather than 4 chars (32-bit) at once. When using earlycon,
> __msm_console_write() always writes 4 characters at a time, but we don't
> know which mode the bootloader was using and we don't set the mode either.
> 
> This causes garbled output if the bootloader was using the single-character
> mode, because only every 4th character appears in the serial console, e.g.
> 
>    "[ 00oni pi  000xf0[ 00i s 5rm9(l)l s 1  1 SPMTA 7:C 5[ 00A ade k d[
>     00ano:ameoi .Q1B[ 00ac _idaM00080oo'"
> 
> If the bootloader was using the DMA ("DM") mode, output would likely fail
> entirely. Later, when the full serial driver probes, the port is
> re-initialized and output works as expected.
> 
> Fix this also for earlycon by clearing the DMEN register and
> reset+re-enable the transmitter to apply the change. This ensures the
> transmitter is in the expected state before writing any output.
> 
> Cc: stable@...r.kernel.org
> Fixes: 0efe72963409 ("tty: serial: msm: Add earlycon support")
> Signed-off-by: Stephan Gerhold <stephan.gerhold@...aro.org>
> ---
>   drivers/tty/serial/msm_serial.c | 6 ++++++
>   1 file changed, 6 insertions(+)
> 
> diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
> index 1b137e06844425584afe5d3f647e9537c6e2d658..3449945493ceb42369d2acafca925350fccc4f82 100644
> --- a/drivers/tty/serial/msm_serial.c
> +++ b/drivers/tty/serial/msm_serial.c
> @@ -1746,6 +1746,12 @@ msm_serial_early_console_setup_dm(struct earlycon_device *device,
>   	if (!device->port.membase)
>   		return -ENODEV;
>   
> +	/* Disable DM / single-character modes */
> +	msm_write(&device->port, 0, UARTDM_DMEN);
> +	msm_write(&device->port, MSM_UART_CR_CMD_RESET_RX, MSM_UART_CR);
> +	msm_write(&device->port, MSM_UART_CR_CMD_RESET_TX, MSM_UART_CR);
> +	msm_write(&device->port, MSM_UART_CR_TX_ENABLE, MSM_UART_CR);
> +
>   	device->con->write = msm_serial_early_write_dm;
>   	return 0;
>   }
> 
> ---
> base-commit: 0af2f6be1b4281385b618cb86ad946eded089ac8
> change-id: 20250408-msm-serial-earlycon-4c5dfa782496
> 
> Best regards,

I think it's safe the sanitize the mode in earlycon.

Reviewed-by: Neil Armstrong <neil.armstrong@...aro.org>

Thanks
Neil