Message-ID: <20250420173829.200553-4-marek.vasut+renesas@mailbox.org>
Date: Sun, 20 Apr 2025 19:36:29 +0200
From: Marek Vasut <marek.vasut+renesas@...lbox.org>
To: linux-arm-kernel@...ts.infradead.org
Cc: Marek Vasut <marek.vasut+renesas@...lbox.org>,
	Kuninori Morimoto <kuninori.morimoto.gx@...esas.com>,
	Niklas Söderlund <niklas.soderlund+renesas@...natech.se>,
	Krzysztof Wilczyński <kw@...ux.com>,
	Rafał Miłecki <rafal@...ecki.pl>,
	Aradhya Bhatia <a-bhatia1@...com>,
	Bjorn Helgaas <bhelgaas@...gle.com>,
	Conor Dooley <conor+dt@...nel.org>,
	Geert Uytterhoeven <geert+renesas@...der.be>,
	Heiko Stuebner <heiko@...ech.de>,
	Junhao Xie <bigfoot@...ssfun.cn>,
	Kever Yang <kever.yang@...k-chips.com>,
	Krzysztof Kozlowski <krzk+dt@...nel.org>,
	Lorenzo Pieralisi <lpieralisi@...nel.org>,
	Magnus Damm <magnus.damm@...il.com>,
	Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>,
	Neil Armstrong <neil.armstrong@...aro.org>,
	Rob Herring <robh@...nel.org>,
	Yoshihiro Shimoda <yoshihiro.shimoda.uh@...esas.com>,
	devicetree@...r.kernel.org,
	linux-kernel@...r.kernel.org,
	linux-pci@...r.kernel.org,
	linux-renesas-soc@...r.kernel.org
Subject: [PATCH v3 3/3] arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support

Add Retronix R-Car V4H Sparrow Hawk board based on Renesas R-Car V4H ES3.0
(R8A779G3) SoC. This is a single-board computer with single gigabit ethernet,
DSI-to-eDP bridge, DSI and two CSI2 interfaces, audio codec, two CANFD ports,
micro SD card slot, USB PD supply, USB 3.0 ports, M.2 Key-M slot for NVMe SSD,
debug UART and JTAG.

Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@...esas.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@...natech.se>
Signed-off-by: Marek Vasut <marek.vasut+renesas@...lbox.org>
---
Cc: "Krzysztof Wilczyński" <kw@...ux.com>
Cc: "Rafał Miłecki" <rafal@...ecki.pl>
Cc: Aradhya Bhatia <a-bhatia1@...com>
Cc: Bjorn Helgaas <bhelgaas@...gle.com>
Cc: Conor Dooley <conor+dt@...nel.org>
Cc: Geert Uytterhoeven <geert+renesas@...der.be>
Cc: Heiko Stuebner <heiko@...ech.de>
Cc: Junhao Xie <bigfoot@...ssfun.cn>
Cc: Kever Yang <kever.yang@...k-chips.com>
Cc: Krzysztof Kozlowski <krzk+dt@...nel.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@...esas.com>
Cc: Lorenzo Pieralisi <lpieralisi@...nel.org>
Cc: Magnus Damm <magnus.damm@...il.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
Cc: Neil Armstrong <neil.armstrong@...aro.org>
Cc: Rob Herring <robh@...nel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@...esas.com>
Cc: devicetree@...r.kernel.org
Cc: linux-kernel@...r.kernel.org
Cc: linux-pci@...r.kernel.org
Cc: linux-renesas-soc@...r.kernel.org
---
V2: - Add TB from Morimoto-san
    - Enable pwm-fan and set PWM to full by default, to achieve maximum
      cooling effect unless configured otherwise. The blower fan is user
      supplied device, hence this default.
    - Add arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
      to demonstrate user supplied blower fan configuration.
    - Add TB from Niklas
    - Rename pins{_,-}mdio, pins{_,-}mii, scif{_,-}clk, sd{_,-}uhs
    - Add serial1 = &hscif1; and serial2 = &hscif3
    - Rename {Renesas,Retronix} R-Car V4H Sparrow Hawk in commit message
      and update R-Car V4H ES3.0 to Renesas R-Car V4H ES3.0
V3: - Remove Renesas 9FGV0441 PCIe clock generator node from I2C bus,
      remove clk-x8 clock node used by the PCIe clock generator, use
      pcie0_clkref and pcie1_clkref to describe 100 MHz clock supplied
      to both the PCIe controller and bus for now. The 9FGV0441 can and
      does operate autonomously without any configuration. The 9FGV0441
      description will be added in a separate follow up patch, once it
      is clear how to describe separate controller and bus clock in DT.
---
 arch/arm64/boot/dts/renesas/Makefile          |   4 +
 .../r8a779g3-sparrow-hawk-fan-pwm.dtso        |  43 ++
 .../dts/renesas/r8a779g3-sparrow-hawk.dts     | 666 ++++++++++++++++++
 3 files changed, 713 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index d8a8d7ca4c58a..b24dddee3827c 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -94,6 +94,10 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single.dtb
 r8a779g2-white-hawk-single-ard-audio-da7212-dtbs := r8a779g2-white-hawk-single.dtb white-hawk-ard-audio-da7212.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
 
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
+r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
+
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-white-hawk-single.dtb
 r8a779g3-white-hawk-single-ard-audio-da7212-dtbs := r8a779g3-white-hawk-single.dtb white-hawk-ard-audio-da7212.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-white-hawk-single-ard-audio-da7212.dtb
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
new file mode 100644
index 0000000000000..50d53c8d76c5b
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-fan-pwm.dtso
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Overlay for the PWM controlled blower fan in connector J3:FAN
+ * on R-Car V4H ES3.0 Sparrow Hawk board
+ *
+ * Copyright (C) 2025 Marek Vasut <marek.vasut+renesas@...lbox.org>
+ *
+ * Example usage:
+ *
+ * # Localize hwmon sysfs directory that matches the PWM fan,
+ * # enable the PWM fan, and configure the fan speed manually.
+ * r8a779g3-sparrow-hawk$ grep -H . /sys/class/hwmon/hwmon?/name
+ * /sys/class/hwmon/hwmon0/name:sensor1_thermal
+ * /sys/class/hwmon/hwmon1/name:sensor2_thermal
+ * /sys/class/hwmon/hwmon2/name:sensor3_thermal
+ * /sys/class/hwmon/hwmon3/name:sensor4_thermal
+ * /sys/class/hwmon/hwmon4/name:pwmfan
+ *                       ^      ^^^^^^
+ *
+ * # Select mode 2 , enable fan PWM and regulator and keep them enabled.
+ * # For details, see Linux Documentation/hwmon/pwm-fan.rst
+ * r8a779g3-sparrow-hawk$ echo 2 > /sys/class/hwmon/hwmon4/pwm1_enable
+ *
+ * # Configure PWM fan speed in range 0..255 , 0 is stopped , 255 is full speed .
+ * # Fan speed 101 is about 2/5 of the PWM fan speed:
+ * r8a779g3-sparrow-hawk$ echo 101 > /sys/class/hwmon/hwmon4/pwm1
+ */
+
+/dts-v1/;
+/plugin/;
+
+/*
+ * Override default PWM fan settings. For a list of available properties,
+ * see schema Documentation/devicetree/bindings/hwmon/pwm-fan.yaml .
+ */
+&fan {
+	/* Available cooling levels */
+	cooling-levels = <0 50 100 150 200 255>;
+	/* Four pulses of tacho signal per one revolution */
+	pulses-per-revolution = <4>;
+	/* PWM period: 100us ~= 10 kHz */
+	pwms = <&pwm0 0 100000>;
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
new file mode 100644
index 0000000000000..b109095a0d872
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts
@@ -0,0 +1,666 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the R-Car V4H ES3.0 Sparrow Hawk board
+ *
+ * Copyright (C) 2025 Marek Vasut <marek.vasut+renesas@...lbox.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+
+#include "r8a779g3.dtsi"
+
+/ {
+	model = "Retronix Sparrow Hawk board based on r8a779g3";
+	compatible = "retronix,sparrow-hawk", "renesas,r8a779g3",
+		     "renesas,r8a779g0";
+
+	aliases {
+		ethernet0 = &avb0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		serial0 = &hscif0;
+		serial1 = &hscif1;
+		serial2 = &hscif3;
+		spi0 = &rpc;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:921600n8";
+	};
+
+	/* Page 31 / FAN */
+	fan: pwm-fan {
+		pinctrl-0 = <&irq4_pins>;
+		pinctrl-names = "default";
+		compatible = "pwm-fan";
+		#cooling-cells = <2>;
+		interrupts-extended = <&intc_ex 4 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * The fan model connected to this device can be selected
+		 * by user. Set "cooling-levels" DT property to single 255
+		 * entry to force the fan PWM into constant HIGH, which
+		 * forces the fan to spin at maximum RPM, thus providing
+		 * maximum cooling to this device and protection against
+		 * misconfigured PWM duty cycle to the fan.
+		 *
+		 * User has to configure "pwms" and "pulses-per-revolution"
+		 * DT properties according to fan datasheet first, and then
+		 * extend "cooling-levels = <0 m n ... 255>" property to
+		 * achieve proper fan control compatible with fan model
+		 * installed by user.
+		 */
+		cooling-levels = <255>;
+		pulses-per-revolution = <2>;
+		pwms = <&pwm0 0 50000>;
+	};
+
+	/*
+	 * Page 15 / LPDDR5
+	 *
+	 * This configuration listed below is for the 8 GiB board variant
+	 * with MT62F1G64D8EK-023 WT:C LPDDR5 part populated on the board.
+	 *
+	 * A variant with 16 GiB MT62F2G64D8EK-023 WT:C part populated on
+	 * the board is automatically handled by the bootloader, which
+	 * adjusts the correct DRAM size into the memory nodes below.
+	 */
+	memory@...00000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@...000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	memory@...000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x1 0x00000000>;
+	};
+
+	/* Page 27 / DSI to Display */
+	mini-dp-con {
+		compatible = "dp-connector";
+		label = "CN6";
+		type = "full-size";
+
+		port {
+			mini_dp_con_in: endpoint {
+				remote-endpoint = <&sn65dsi86_out>;
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	/* Page 27 / DSI to Display */
+	sn65dsi86_refclk: clk-x9 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <38400000>;
+	};
+
+	/* Page 17 uSD-Slot */
+	vcc_sdhi: regulator-vcc-sdhi {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio8 13 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 0>, <1800000 1>;
+	};
+};
+
+/* Page 22 / Ether_AVB0 */
+&avb0 {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&avb0_phy>;
+	tx-internal-delay-ps = <2000>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		avb0_phy: ethernet-phy@0 {	/* KSZ9031RNXVB */
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			rxc-skew-ps = <1500>;
+			reg = <0>;
+			/* AVB0_PHY_INT_V */
+			interrupts-extended = <&gpio7 5 IRQ_TYPE_LEVEL_LOW>;
+			/* GP7_10/AVB0_RESETN_V */
+			reset-gpios = <&gpio7 10 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+/* Page 28 / CANFD_IF */
+&can_clk {
+	clock-frequency = <40000000>;
+};
+
+/* Page 28 / CANFD_IF */
+&canfd {
+	pinctrl-0 = <&canfd3_pins>, <&canfd4_pins>, <&can_clk_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	channel3 {
+		status = "okay";
+	};
+
+	channel4 {
+		status = "okay";
+	};
+};
+
+/* Page 27 / DSI to Display */
+&dsi1 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			dsi1_out: endpoint {
+				remote-endpoint = <&sn65dsi86_in>;
+				data-lanes = <1 2 3 4>;
+			};
+		};
+	};
+};
+
+/* Page 27 / DSI to Display */
+&du {
+	status = "okay";
+};
+
+/* Page 5 / R-Car V4H_INT_I2C */
+&extal_clk {	/* X3 */
+	clock-frequency = <16666666>;
+};
+
+/* Page 5 / R-Car V4H_INT_I2C */
+&extalr_clk {	/* X2 */
+	clock-frequency = <32768>;
+};
+
+/* Page 26 / 2230 Key M M.2 */
+&gpio4 {
+	/* 9FGV0441 nOE inputs 0 and 1 */
+	pcie-m2-oe-hog {
+		gpio-hog;
+		gpios = <21 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "PCIe-CLK-nOE-M2";
+	};
+
+	/* 9FGV0441 nOE inputs 2 and 3 */
+	pcie-usb-oe-hog {
+		gpio-hog;
+		gpios = <22 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "PCIe-CLK-nOE-USB";
+	};
+};
+
+/* Page 23 / DEBUG */
+&hscif0 {	/* FTDI ADBUS[3:0] */
+	pinctrl-0 = <&hscif0_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	bootph-all;
+
+	status = "okay";
+};
+
+/* Page 23 / DEBUG */
+&hscif1 {	/* FTDI BDBUS[3:0] */
+	pinctrl-0 = <&hscif1_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	status = "okay";
+};
+
+/* Page 24 / UART */
+&hscif3 {	/* CN7 pins 8 (TX) and 10 (RX) */
+	pinctrl-0 = <&hscif3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+/* Page 24 / I2C SWITCH */
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+
+	mux@71 {
+		compatible = "nxp,pca9544";	/* TCA9544 */
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&reg_3p3v>;
+
+		i2c0_mux0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Page 27 / DSI to Display */
+			bridge@2c {
+				pinctrl-0 = <&irq0_pins>;
+				pinctrl-names = "default";
+
+				compatible = "ti,sn65dsi86";
+				reg = <0x2c>;
+
+				clocks = <&sn65dsi86_refclk>;
+				clock-names = "refclk";
+
+				interrupts-extended = <&intc_ex 0 IRQ_TYPE_LEVEL_HIGH>;
+
+				enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+
+				vccio-supply = <&reg_1p8v>;
+				vpll-supply = <&reg_1p8v>;
+				vcca-supply = <&reg_1p2v>;
+				vcc-supply = <&reg_1p2v>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						sn65dsi86_in: endpoint {
+							remote-endpoint = <&dsi1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						sn65dsi86_out: endpoint {
+							remote-endpoint = <&mini_dp_con_in>;
+						};
+					};
+				};
+			};
+		};
+
+		i2c0_mux1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c0_mux2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c0_mux3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+/* Page 29 / CSI_IF_CN / CAM_CN0 */
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+};
+
+/* Page 29 / CSI_IF_CN / CAM_CN1 */
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+};
+
+/* Page 31 / IO_CN */
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+};
+
+/* Page 31 / IO_CN */
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c4_pins>;
+	pinctrl-names = "default";
+};
+
+/* Page 18 / POWER_CORE and Page 19 / POWER_PMIC */
+&i2c5 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&i2c5_pins>;
+	pinctrl-names = "default";
+};
+
+/* Page 17 uSD-Slot */
+&mmc0 {
+	pinctrl-0 = <&sd_pins>;
+	pinctrl-1 = <&sd_uhs_pins>;
+	pinctrl-names = "default", "state_uhs";
+	bus-width = <4>;
+	cd-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;	/* SD_CD */
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vcc_sdhi>;
+	status = "okay";
+};
+
+/* Page 26 / 2230 Key M M.2 */
+&pcie0_clkref {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	reset-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* Page 25 / PCIe to USB */
+&pcie1_clkref {
+	clock-frequency = <100000000>;
+};
+
+&pciec1 {
+	/* uPD720201 is PCIe Gen2 x1 device */
+	num-lanes = <1>;
+	reset-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Page 22 / Ether_AVB0 */
+	avb0_pins: avb0 {
+		mux {
+			groups = "avb0_link", "avb0_mdio", "avb0_rgmii",
+				 "avb0_txcrefclk";
+			function = "avb0";
+		};
+
+		pins-mdio {
+			groups = "avb0_mdio";
+			drive-strength = <21>;
+		};
+
+		pins-mii {
+			groups = "avb0_rgmii";
+			drive-strength = <21>;
+		};
+
+	};
+
+	/* Page 28 / CANFD_IF */
+	can_clk_pins: can-clk {
+		groups = "can_clk";
+		function = "can_clk";
+	};
+
+	/* Page 28 / CANFD_IF */
+	canfd3_pins: canfd3 {
+		groups = "canfd3_data";
+		function = "canfd3";
+	};
+
+	/* Page 28 / CANFD_IF */
+	canfd4_pins: canfd4 {
+		groups = "canfd4_data";
+		function = "canfd4";
+	};
+
+	/* Page 23 / DEBUG */
+	hscif0_pins: hscif0 {
+		groups = "hscif0_data", "hscif0_ctrl";
+		function = "hscif0";
+	};
+
+	/* Page 23 / DEBUG */
+	hscif1_pins: hscif1 {
+		groups = "hscif1_data_a", "hscif1_ctrl_a";
+		function = "hscif1";
+	};
+
+	/* Page 24 / UART */
+	hscif3_pins: hscif3 {
+		groups = "hscif3_data_a";
+		function = "hscif3";
+	};
+
+	/* Page 24 / I2C SWITCH */
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	/* Page 29 / CSI_IF_CN / CAM_CN0 */
+	i2c1_pins: i2c1 {
+		groups = "i2c1";
+		function = "i2c1";
+	};
+
+	/* Page 29 / CSI_IF_CN / CAM_CN1 */
+	i2c2_pins: i2c2 {
+		groups = "i2c2";
+		function = "i2c2";
+	};
+
+	/* Page 31 / IO_CN */
+	i2c3_pins: i2c3 {
+		groups = "i2c3";
+		function = "i2c3";
+	};
+
+	/* Page 31 / IO_CN */
+	i2c4_pins: i2c4 {
+		groups = "i2c4";
+		function = "i2c4";
+	};
+
+	/* Page 18 / POWER_CORE */
+	i2c5_pins: i2c5 {
+		groups = "i2c5";
+		function = "i2c5";
+	};
+
+	/* Page 27 / DSI to Display */
+	irq0_pins: irq0 {
+		groups = "intc_ex_irq0_a";
+		function = "intc_ex";
+	};
+
+	/* Page 31 / FAN */
+	irq4_pins: irq4 {
+		groups = "intc_ex_irq4_b";
+		function = "intc_ex";
+	};
+
+	/* Page 31 / FAN */
+	pwm0_pins: pwm0 {
+		groups = "pwm0";
+		function = "pwm0";
+	};
+
+	/* Page 31 / CN7 pin 12 */
+	pwm1_pins: pwm1 {
+		groups = "pwm1_b";
+		function = "pwm1";
+	};
+
+	/* Page 31 / CN7 pin 32 */
+	pwm6_pins: pwm6 {
+		groups = "pwm6";
+		function = "pwm6";
+	};
+
+	/* Page 31 / CN7 pin 33 */
+	pwm7_pins: pwm7 {
+		groups = "pwm7";
+		function = "pwm7";
+	};
+
+	/* Page 16 / QSPI_FLASH */
+	qspi0_pins: qspi0 {
+		groups = "qspi0_ctrl", "qspi0_data4";
+		function = "qspi0";
+		bootph-all;
+	};
+
+	/* Page 6 / SCIF_CLK_SOC_V */
+	scif_clk_pins: scif-clk {
+		groups = "scif_clk";
+		function = "scif_clk";
+	};
+
+	/* Page 17 uSD-Slot */
+	sd_pins: sd {
+		groups = "mmc_data4", "mmc_ctrl";
+		function = "mmc";
+		power-source = <3300>;
+	};
+
+	/* Page 17 uSD-Slot */
+	sd_uhs_pins: sd-uhs {
+		groups = "mmc_data4", "mmc_ctrl";
+		function = "mmc";
+		power-source = <1800>;
+	};
+};
+
+/* Page 31 / FAN */
+&pwm0 {
+	pinctrl-0 = <&pwm0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Page 31 / CN7 pin 12 */
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Page 31 / CN7 pin 32 */
+&pwm6 {
+	pinctrl-0 = <&pwm6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Page 31 / CN7 pin 33 */
+&pwm7 {
+	pinctrl-0 = <&pwm7_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Page 16 / QSPI_FLASH */
+&rpc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+	bootph-all;
+
+	status = "okay";
+
+	flash@0 {
+		compatible = "spansion,s25fs512s", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		bootph-all;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				reg = <0x0 0x1000000>;
+				read-only;
+			};
+
+			user@...0000 {
+				reg = <0x1000000 0x2f80000>;
+			};
+
+			env1@...0000 {
+				reg = <0x3f80000 0x40000>;
+			};
+
+			env2@...0000 {
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+/* Page 6 / SCIF_CLK_SOC_V */
+&scif_clk {	/* X12 */
+	clock-frequency = <24000000>;
+};
-- 
2.47.2

Powered by blists - more mailing lists