[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <f223d5ec-5549-414a-842d-b9aeb80915e5@ti.com>
Date: Fri, 2 May 2025 13:45:47 +0530
From: Devarsh Thakkar <devarsht@...com>
To: Rishikesh Donadkar <r-donadkar@...com>, <nm@...com>, <vigneshr@...com>
CC: <kristo@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
<conor+dt@...nel.org>, <vaishnav.a@...com>, <y-abhilashchandra@...com>,
<s-jain1@...com>, <jai.luthra@...ux.dev>,
<jai.luthra@...asonboard.com>, <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<imx@...ts.linux.dev>
Subject: Re: [PATCH v1 2/4] arm64: dts: ti: k3-am62x: Add required voltage
supplies for IMX219
On 29/04/25 21:11, Rishikesh Donadkar wrote:
> The device tree overlay for the IMX219 sensor requires three voltage
> supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
> (digital I/O).
>
> Add the corresponding voltage supply definitions to avoid dtbs_check
> warnings.
>
On a side-note device-tree overlay requiring these voltages is an
implied reason, it's mainly because the schematics mention that and
bindings want to capture same topography in device-tree too.
So maybe good to mention that and share schematic link too in commit
message :
https://datasheets.raspberrypi.com/camera/camera-module-2-schematics.pdf
With these changes, feel free to add,
Reviewed-by: Devarsh Thakkar <devarsht@...com>
Regards
Devarsh
> Signed-off-by: Rishikesh Donadkar <r-donadkar@...com>
> ---
> .../boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso | 31 +++++++++++++++++++
> 1 file changed, 31 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> index dd090813a32d6..149c59c071823 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
> @@ -15,6 +15,33 @@ clk_imx219_fixed: imx219-xclk {
> #clock-cells = <0>;
> clock-frequency = <24000000>;
> };
> +
> + reg_2p8v: regulator-2p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + vin-supply = <&vcc_3v3_sys>;
> + regulator-always-on;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_3v3_sys>;
> + regulator-always-on;
> + };
> +
> + reg_1p2v: regulator-1p2v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P2V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + vin-supply = <&vcc_3v3_sys>;
> + regulator-always-on;
> + };
> };
>
> &main_i2c2 {
> @@ -40,6 +67,10 @@ ov5640: camera@10 {
>
> clocks = <&clk_imx219_fixed>;
>
> + VANA-supply = <®_2p8v>;
> + VDIG-supply = <®_1p8v>;
> + VDDL-supply = <®_1p2v>;
> +
> reset-gpios = <&exp1 13 GPIO_ACTIVE_HIGH>;
>
> port {
Powered by blists - more mailing lists