Message-ID: <bb171ae2-c495-49a3-a7eb-a4b865e54199@kwiboo.se>
Date: Sun, 4 May 2025 15:26:49 +0200
From: Jonas Karlman <jonas@...boo.se>
To: John Clark <inindev@...il.com>
Cc: heiko@...ech.de, robh@...nel.org, conor+dt@...nel.org,
 detlev.casanova@...labora.com, linux-kernel@...r.kernel.org,
 linux-rockchip@...ts.infradead.org, devicetree@...r.kernel.org,
 krzk+dt@...nel.org, linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v2 3/3] arm64: dts: rockchip: Add Luckfox Omni3576 Board
 support

Hi John,

On 2025-05-04 12:24, John Clark wrote:
> Add device tree for the Luckfox Omni3576 Carrier Board with Core3576
> Module, powered by the Rockchip RK3576 SoC with four Cortex-A72 cores,
> four Cortex-A53 cores, and a Mali-G52 MC3 GPU. This initial
> implementation enables essential functionality for booting Linux and
> basic connectivity.
> 
> Supported and tested features:
>  - UART for serial console
>  - SD card for storage
>  - PCIe with NVMe SSD (detected, mounted, and fully functional)
>  - Gigabit Ethernet 0 with RGMII PHY
>  - USB 2.0 host ports
>  - RK806 PMIC for power management
>  - RTC with timekeeping and wake-up
>  - GPIO-controlled LED with heartbeat trigger
>  - eMMC (enabled, not populated on tested board)
> 
> The device tree provides a foundation for further peripheral support, such
> as WiFi, MIPI-DSI, HDMI, and Ethernet 1, in future updates.
> 
> Tested on Linux 6.15-rc4
> 
> Signed-off-by: John Clark <inindev@...il.com>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../dts/rockchip/rk3576-luckfox-omni3576.dts  | 779 ++++++++++++++++++
>  2 files changed, 780 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts
> 
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 7948522cb225..22d74367b7e6 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-luckfox-omni3576.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-roc-pc.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-rock-4d.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3582-radxa-e52c.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts
> new file mode 100644
> index 000000000000..73351ba7830c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts
> @@ -0,0 +1,779 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3576.dtsi"
> +
> +/ {
> +	model = "Luckfox Omni3576";
> +	compatible = "luckfox,omni3576", "rockchip,rk3576";
> +
> +	aliases {
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +		mmc0 = &sdhci;
> +		mmc1 = &sdmmc;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:1500000n8";
> +	};
> +
> +	hdmi-con {
> +		compatible = "hdmi-connector";
> +		hdmi-pwr-supply = <&vcc_5v0_hdmi>;
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	leds: leds {
> +		compatible = "gpio-leds";
> +
> +		green_led: green-led {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_HEARTBEAT;
> +			gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;

This should probably also have a pinctrl to configure the gpio pin
referenced here.

> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +
> +	vcc_5v0_dcin: regulator-vcc-5v0-dcin {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v0_dcin";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_1v1_nldo_s3";
> +		regulator-boot-on;
> +		regulator-always-on;

Please use consistent property order for all regulator nodes, e.g.
vcc_5v0_dcin used always-on before boot-on, and here you use boot-on
before always-on.

> +		regulator-min-microvolt = <1100000>;
> +		regulator-max-microvolt = <1100000>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +
> +	vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_2v0_pldo_s3";
> +		regulator-boot-on;
> +		regulator-always-on;

Same here.

> +		regulator-min-microvolt = <2000000>;
> +		regulator-max-microvolt = <2000000>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +
> +	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pcie_pwr_en>;
> +		regulator-name = "vcc_3v3_pcie";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		enable-active-high;
> +		gpio = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;

Please use the gpios property instead of the somewhat depracated gpio
property. Also please consider consistent property order.

> +		startup-delay-us = <1000>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +
> +	vcc_3v3_rtc_s5: regulator-vcc-3v3-rtc-s5 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_3v3_rtc_s5";
> +		regulator-boot-on;
> +		regulator-always-on;

Same here.

> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +
> +	vbus_5v0_typec: regulator-vbus-5v0-typec {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vbus5v0_typec";
> +		enable-active-high;
> +		gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;

Same here.

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_otg0_pwr_en>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v0_device>;
> +	};
> +
> +	vcc_5v0_host: regulator-vcc-5v0-host {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v0_host";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;

Same here.
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_host_pwr_en>;
> +		regulator-boot-on;
> +		regulator-always-on;

Same here.

> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v0_device>;
> +	};
> +
> +	vcc_5v0_sys: regulator-vcc-5v0-sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v0_dcin>;
> +	};
> +
> +	vcc_5v0_device: regulator-vcc-5v0-device {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v0_device";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v0_dcin>;
> +	};
> +
> +	vcc_5v0_hdmi: regulator-vcc-5v0-hdmi {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v0_hdmi";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		regulator-boot-on;

And here always/boot-on are listed after min/max props, please use
consistent property order.

> +		enable-active-high;
> +		gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;

Same as above regarding gpio vs gpios.

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&hdmi_con_en>;
> +		vin-supply = <&vcc_5v0_sys>;
> +	};
> +};
> +
> +&combphy0_ps {
> +	status = "okay";
> +};
> +
> +&combphy1_psu {
> +	status = "okay";
> +};
> +
> +&cpu_l0 {
> +	cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l1 {
> +	cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l2 {
> +	cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l3 {
> +	cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_b0 {
> +	cpu-supply = <&vdd_cpu_big_s0>;
> +};
> +
> +&cpu_b1 {
> +	cpu-supply = <&vdd_cpu_big_s0>;
> +};
> +
> +&cpu_b2 {
> +	cpu-supply = <&vdd_cpu_big_s0>;
> +};
> +
> +&cpu_b3 {
> +	cpu-supply = <&vdd_cpu_big_s0>;
> +};
> +
> +&gmac0 {
> +	clock_in_out = "output";
> +	phy-handle = <&rgmii_phy0>;
> +	phy-mode = "rgmii-rxid";

See Andrew's remark on v1 of this patch.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&eth0m0_miim
> +		     &eth0m0_tx_bus2
> +		     &eth0m0_rx_bus2
> +		     &eth0m0_rgmii_clk
> +		     &eth0m0_rgmii_bus
> +		     &ethm0_clk0_25m_out>;
> +	snps,reset-gpio = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	snps,reset-delays-us = <0 20000 100000>;

The snps,reset- props are depracated, please move to reset props in the
Ethernet PHY node.

> +	tx_delay = <0x20>;
> +	status = "okay";
> +};
> +
> +&gmac1 {
> +	clock_in_out = "output";
> +	phy-handle = <&rgmii_phy1>;
> +	phy-mode = "rgmii-rxid";

Same here.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&eth1m0_miim
> +		     &eth1m0_tx_bus2
> +		     &eth1m0_rx_bus2
> +		     &eth1m0_rgmii_clk
> +		     &eth1m0_rgmii_bus
> +		     &ethm0_clk1_25m_out>;
> +	snps,reset-gpio = <&gpio2 RK_PB4 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	snps,reset-delays-us = <0 20000 100000>;

Same here.

> +	tx_delay = <0x20>;
> +	status = "okay";
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu_s0>;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +};
> +
> +&hdmi_in {
> +	hdmi_in_vp0: endpoint {
> +		remote-endpoint = <&vp0_out_hdmi>;
> +	};
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&hdptxphy {
> +	phy-supply = <&vdda0v75_hdmi_s0>;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +
> +	pmic@23 {
> +		compatible = "rockchip,rk806";
> +		reg = <0x23>;
> +		#gpio-cells = <2>;
> +		gpio-controller;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default", "pmic-power-off";

To my knowledge the pmic-power-off state is vendor kernel specific and
should probably not be added without being described in the dt-binding.

> +		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> +			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> +		pinctrl-1 = <&rk806_dvs1_pwrdn>;
> +		system-power-controller;
> +
> +		vcc1-supply = <&vcc_5v0_sys>;
> +		vcc2-supply = <&vcc_5v0_sys>;
> +		vcc3-supply = <&vcc_5v0_sys>;
> +		vcc4-supply = <&vcc_5v0_sys>;
> +		vcc5-supply = <&vcc_5v0_sys>;
> +		vcc6-supply = <&vcc_5v0_sys>;
> +		vcc7-supply = <&vcc_5v0_sys>;
> +		vcc8-supply = <&vcc_5v0_sys>;
> +		vcc9-supply = <&vcc_5v0_sys>;
> +		vcc10-supply = <&vcc_5v0_sys>;
> +		vcc11-supply = <&vcc_2v0_pldo_s3>;
> +		vcc12-supply = <&vcc_5v0_sys>;
> +		vcc13-supply = <&vcc_1v1_nldo_s3>;
> +		vcc14-supply = <&vcc_1v1_nldo_s3>;
> +		vcca-supply = <&vcc_5v0_sys>;
> +
> +		pwrkey {
> +			status = "okay";
> +		};

This node is vendor specific and is not described in the dt-bindings.

> +
> +		rk806_dvs1_null: dvs1-null-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun0";
> +		};
> +
> +		rk806_dvs2_null: dvs2-null-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun0";
> +		};
> +
> +		rk806_dvs3_null: dvs3-null-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun0";
> +		};
> +
> +		rk806_dvs1_slp: dvs1-slp-pins {
> +			pins = "gpio_pwrctrl1";
> +			function = "pin_fun1";
> +		};
> +
> +		rk806_dvs1_pwrdn: dvs1-pwrdn-pins {
> +			pins = "gpio_pwrctrl1";
> +			function = "pin_fun2";
> +		};
> +
> +		rk806_dvs1_rst: dvs1-rst-pins {
> +			pins = "gpio_pwrctrl1";
> +			function = "pin_fun3";
> +		};
> +
> +		rk806_dvs2_slp: dvs2-slp-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun1";
> +		};
> +
> +		rk806_dvs2_pwrdn: dvs2-pwrdn-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun2";
> +		};
> +
> +		rk806_dvs2_rst: dvs2-rst-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun3";
> +		};
> +
> +		rk806_dvs2_dvs: dvs2-dvs-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun4";
> +		};
> +
> +		rk806_dvs2_gpio: dvs2-gpio-pins {
> +			pins = "gpio_pwrctrl2";
> +			function = "pin_fun5";
> +		};
> +
> +
> +		rk806_dvs3_slp: dvs3-slp-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun1";
> +		};
> +
> +		rk806_dvs3_pwrdn: dvs3-pwrdn-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun2";
> +		};
> +
> +		rk806_dvs3_rst: dvs3-rst-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun3";
> +		};
> +
> +		rk806_dvs3_dvs: dvs3-dvs-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun4";
> +		};
> +
> +		rk806_dvs3_gpio: dvs3-gpio-pins {
> +			pins = "gpio_pwrctrl3";
> +			function = "pin_fun5";
> +		};
> +
> +		regulators {
> +			vdd_cpu_big_s0: dcdc-reg1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-ramp-delay = <12500>;
> +				regulator-name = "vdd_cpu_big_s0";
> +				regulator-enable-ramp-delay = <400>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_npu_s0: dcdc-reg2 {
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-ramp-delay = <12500>;
> +				regulator-name = "vdd_npu_s0";
> +				regulator-enable-ramp-delay = <400>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_cpu_lit_s0: dcdc-reg3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-ramp-delay = <12500>;
> +				regulator-name = "vdd_cpu_lit_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +					regulator-suspend-microvolt = <750000>;
> +				};
> +			};
> +
> +			vcc_3v3_s3: dcdc-reg4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc_3v3_s3";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vdd_gpu_s0: dcdc-reg5 {
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-ramp-delay = <12500>;
> +				regulator-name = "vdd_gpu_s0";
> +				regulator-enable-ramp-delay = <400>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +					regulator-suspend-microvolt = <850000>;
> +				};
> +			};
> +
> +			vddq_ddr_s0: dcdc-reg6 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vddq_ddr_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_logic_s0: dcdc-reg7 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-name = "vdd_logic_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v8_s3: dcdc-reg8 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc_1v8_s3";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vdd2_ddr_s3: dcdc-reg9 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vdd2_ddr_s3";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vdd_ddr_s0: dcdc-reg10 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <550000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-name = "vdd_ddr_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca_1v8_s0: pldo-reg1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcca_1v8_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca1v8_pldo2_s0: pldo-reg2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcca1v8_pldo2_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda_1v2_s0: pldo-reg3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-name = "vdda_1v2_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca_3v3_s0: pldo-reg4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcca_3v3_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd_s0: pldo-reg5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vccio_sd_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca1v8_pldo6_s3: pldo-reg6 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcca1v8_pldo6_s3";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vdd_0v75_s3: nldo-reg1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <750000>;
> +				regulator-name = "vdd_0v75_s3";
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <750000>;
> +				};
> +			};
> +
> +			vdda_ddr_pll_s0: nldo-reg2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-name = "vdda_ddr_pll_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda0v75_hdmi_s0: nldo-reg3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <837500>;
> +				regulator-max-microvolt = <837500>;
> +				regulator-name = "vdda0v75_hdmi_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda_0v85_s0: nldo-reg4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-name = "vdda_0v85_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda_0v75_s0: nldo-reg5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <750000>;
> +				regulator-name = "vdda_0v75_s0";
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2c2 {
> +	status = "okay";

please add a blank line, DT coding style recommend a blank line between
properties and child nodes.

> +	hym8563: rtc@51 {
> +		compatible = "haoyu,hym8563";
> +		reg = <0x51>;
> +		#clock-cells = <0>;
> +		clock-output-names = "hym8563";
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&hym8563_int>;
> +		wakeup-source;
> +	};
> +};
> +
> +&mdio0 {
> +	rgmii_phy0: phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x0>;
> +		clocks = <&cru REFCLKO25M_GMAC0_OUT>;

Please add Ethernet PHY reset props here.

> +	};
> +};
> +
> +&mdio1 {
> +	rgmii_phy1: phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x0>;
> +		clocks = <&cru REFCLKO25M_GMAC1_OUT>;

And here.

> +	};
> +};
> +
> +&pcie0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_reset>;
> +	reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
> +	vpcie3v3-supply = <&vcc_3v3_pcie>;
> +	status = "okay";
> +};
> +
> +&pinctrl {
> +	hdmi {
> +		hdmi_con_en: hdmi-con-en {
> +			rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	hym8563 {
> +		hym8563_int: hym8563-int {
> +			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	leds {
> +		led_green_pin: led-green-pin {
> +			rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pcie {
> +		pcie_pwr_en: pcie-pwr-en {
> +			rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +
> +		pcie_reset: pcie-reset {
> +			rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	usb {
> +		usb_host_pwr_en: usb-host-pwr-en {
> +			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		usb_otg0_pwr_en: usb-otg0-pwr-en {
> +			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		usbc0_int: usbc0-int {
> +			rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +};
> +
> +&saradc {
> +	status = "okay";
> +	vref-supply = <&vcca_1v8_s0>;
> +};
> +
> +&sdhci {
> +	bus-width = <8>;
> +	full-pwr-cycle-in-suspend;
> +	max-frequency = <200000000>;
> +	mmc-hs400-1_8v;
> +	mmc-hs400-enhanced-strobe;
> +	no-sdio;
> +	no-sd;
> +	non-removable;

This should probably have vmmc/vqmmc-supply?

> +	status = "okay";
> +};
> +
> +&sdmmc {
> +	bus-width = <4>;
> +	cap-mmc-highspeed;

Enable of mmc speed when no-mmc look a little bit strange.

> +	cap-sd-highspeed;
> +	disable-wp;
> +	max-frequency = <200000000>;
> +	no-sdio;
> +	no-mmc;

Are we sure about no-mmc? The datasheet for rk3576 list:

SD/MMC interface
- Compliance to SD v3.0, MMC v4.51
- Supports 4-bit data bus

I would suggest you test with no-mmc removed (and cap-mmc-highspeed not
removed) together with a sd-card to emmc adapter, the emmc will probably
be detected and working.

Regards,
Jonas

> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc_3v3_s3>;
> +	vqmmc-supply = <&vccio_sd_s0>;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn>;
> +	status = "okay";
> +};
> +
> +&u2phy1 {
> +	status = "okay";
> +};
> +
> +&u2phy1_otg {
> +	phy-supply = <&vcc_5v0_host>;
> +	status = "okay";
> +};
> +
> +&usb_drd1_dwc3 {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&vop {
> +	vop-supply = <&vdd_logic_s0>;
> +	status = "okay";
> +};
> +
> +&vop_mmu {
> +	status = "okay";
> +};
> +
> +&vp0 {
> +	vp0_out_hdmi: endpoint@...KCHIP_VOP2_EP_HDMI0 {
> +		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> +		remote-endpoint = <&hdmi_in_vp0>;
> +	};
> +};

Powered by blists - more mailing lists