[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <a6329e9d-409e-4f62-b26d-c4d0e49d772c@ti.com>
Date: Wed, 7 May 2025 13:50:12 +0530
From: "Kumar, Udit" <u-kumar1@...com>
To: Yemike Abhilash Chandra <y-abhilashchandra@...com>, <nm@...com>,
<vigneshr@...com>, <kristo@...nel.org>, <robh@...nel.org>,
<krzk+dt@...nel.org>, <conor+dt@...nel.org>
CC: <vaishnav.a@...com>, <r-donadkar@...com>, <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>, <jai.luthra@...ux.dev>,
<linux-kernel@...r.kernel.org>, <u-kumar1@...com>
Subject: Re: [PATCH 2/2] arm64: dts: ti: k3-j722s-evm: Add overlay for TEVI
OV5640
Hello Vaishnav/Abhilash
Thanks for patch
On 5/5/2025 5:27 PM, Yemike Abhilash Chandra wrote:
> From: Vaishnav Achath <vaishnav.a@...com>
>
> TechNexion TEVI OV5640 camera is a 5MP camera that can be used with
> J722S EVM through the 22-pin CSI-RX connector. Add a reference overlay
> for quad TEVI OV5640 modules on J722S EVM.
>
> Signed-off-by: Vaishnav Achath <vaishnav.a@...com>
> Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@...com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 4 +
> .../k3-j722s-evm-csi2-quad-tevi-ov5640.dtso | 358 ++++++++++++++++++
> 2 files changed, 362 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 829a3b028466..76b750e4b8a8 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -123,6 +123,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtbo
> [..]
> diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
> new file mode 100644
> index 000000000000..537224ea60e3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
> @@ -0,0 +1,358 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * 4 x TEVI OV5640 MIPI Camera module on RPI camera connector.
> + *
> + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-pinctrl.h"
> +
> +&{/} {
> + clk_ov5640_fixed: clock-24000000 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24000000>;
> + };
> +
Please check once , this is clock is 25M or 24M .
As I see CDC6CE025000ADLXT/U28 is marked as 25M OSC
> + reg_2p8v: regulator-2p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + vin-supply = <&vdd_sd_dv>;
> + regulator-always-on;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vdd_sd_dv>;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vdd_sd_dv>;
> + regulator-always-on;
> + };
Sorry but on connector QSH-020-01-L-D-DP-A-K/J27, I see only 3v3 available.
May be I am missing something here but how you are getting 1v8 and 2v8
supply
> +};
> +
> +
> +&main_pmx0 {
> + cam0_reset_pins_default: cam0-default-reset-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x03c, PIN_OUTPUT, 7)
> + >;
> + };
> +
Please mark GPIO you are using for this in comment
example
J722S_IOPAD(0x1dc, PIN_INPUT, 0) /* (C22) MCAN0_RX */
> + cam1_reset_pins_default: cam1-default-reset-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x044, PIN_OUTPUT, 7)
> + >;
> + };
> +
> + cam2_reset_pins_default: cam2-default-reset-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x04c, PIN_OUTPUT, 7)
> + >;
> + };
> +
> + cam3_reset_pins_default: cam3-default-reset-pins {
> + pinctrl-single,pins = <
> + J722S_IOPAD(0x054, PIN_OUTPUT, 7)
> + >;
> + };
> +};
> +
> +&exp1 {
> + p06-hog{
> + /* P06 - CSI01_MUX_SEL_2 */
> + gpio-hog;
> + gpios = <6 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI01_MUX_SEL_2";
As per table on page 29
CSI01_MUX_SEL_2 as low means, INPUT<-- A Port [CSI2 Connector]
Please check, if you want to drive this line high or low
> + };
> +
> + p07-hog{
> + /* P01 - CSI23_MUX_SEL_2 */
> + gpio-hog;
> + gpios = <7 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI23_MUX_SEL_2";
> + };
Same as for CSI01_MUX_SEL_2, table on page-30
> +};
> +
> +&main_gpio0 {
> + p15-hog {
> + /* P15 - CSI2_CAMERA_GPIO1 */
> + gpio-hog;
> + gpios = <15 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO1";
> + };
> +
> + p17-hog {
> + /* P17 - CSI2_CAMERA_GPIO2 */
> + gpio-hog;
> + gpios = <17 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO2";
> + };
> +
> + p19-hog {
> + /* P19 - CSI2_CAMERA_GPIO3 */
> + gpio-hog;
> + gpios = <19 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO3";
> + };
> +
> + p21-hog {
> + /* P21 - CSI2_CAMERA_GPIO4 */
> + gpio-hog;
> + gpios = <21 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO4";
> + };
Please check once if P21 and rest above are pin number of SOC ?
> +};
> +
> +&pca9543_0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + ov5640_0: camera@3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> + clocks = <&clk_ov5640_fixed>;
> + clock-names = "xclk";
> +
> + AVDD-supply = <®_2p8v>;
> + DOVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_3p3v>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cam0_reset_pins_default>;
do you think, you should have reset-gpios as property for this ov5640
and other nodes too ?
> +
> [..]
Powered by blists - more mailing lists