| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250508155134.2026300-5-y-abhilashchandra@ti.com>
Date: Thu, 8 May 2025 21:21:34 +0530
From: Yemike Abhilash Chandra <y-abhilashchandra@...com>
To: <nm@...com>, <vigneshr@...com>, <kristo@...nel.org>, <robh@...nel.org>,
<krzk+dt@...nel.org>, <conor+dt@...nel.org>
CC: <vaishnav.a@...com>, <u-kumar1@...com>, <r-donadkar@...com>,
<devicetree@...r.kernel.org>, <linux-arm-kernel@...ts.infradead.org>,
<jai.luthra@...ux.dev>, <linux-kernel@...r.kernel.org>,
<y-abhilashchandra@...com>
Subject: [PATCH v2 4/4] arm64: dts: ti: k3-j722s-evm: Add overlay for TEVI OV5640
From: Vaishnav Achath <vaishnav.a@...com>
TechNexion TEVI OV5640 camera is a 5MP camera that can be used with
J722S EVM through the 22-pin CSI-RX connector. Add a reference overlay
for quad TEVI OV5640 modules on J722S EVM.
Signed-off-by: Vaishnav Achath <vaishnav.a@...com>
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@...com>
---
arch/arm64/boot/dts/ti/Makefile | 4 +
.../k3-j722s-evm-csi2-quad-tevi-ov5640.dtso | 322 ++++++++++++++++++
2 files changed, 326 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index b317eaff64cc..b0ac5c05274f 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -133,6 +133,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-tevi-ov5640.dtbo
# Boards with J784s4 SoC
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
@@ -230,6 +231,8 @@ k3-j742s2-evm-usb0-type-a-dtbs := k3-j742s2-evm.dtb \
k3-j784s4-j742s2-evm-usb0-type-a.dtbo
k3-j722s-evm-csi2-quad-rpi-cam-imx219-dtbs := k3-j722s-evm.dtb \
k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtbo
+k3-j722s-evm-csi2-quad-tevi-ov5640-dtbs := k3-j722s-evm.dtb \
+ k3-j722s-evm-csi2-quad-tevi-ov5640.dtbo
k3-j784s4-evm-pcie0-pcie1-ep-dtbs := k3-j784s4-evm.dtb \
k3-j784s4-evm-pcie0-pcie1-ep.dtbo
k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
@@ -268,6 +271,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-j721s2-evm-pcie1-ep.dtb \
k3-j742s2-evm-usb0-type-a.dtb \
k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtb \
+ k3-j722s-evm-csi2-quad-tevi-ov5640.dtb \
k3-j784s4-evm-pcie0-pcie1-ep.dtb \
k3-j784s4-evm-quad-port-eth-exp1.dtb \
k3-j784s4-evm-usb0-type-a.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
new file mode 100644
index 000000000000..55e767a020d9
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j722s-evm-csi2-quad-tevi-ov5640.dtso
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * 4 x TEVI OV5640 MIPI Camera module on RPI camera connector.
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-pinctrl.h"
+
+&{/} {
+ clk_ov5640_fixed: clock-24000000 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ reg_2p8v: regulator-2p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <&vcc_3v3_exp>;
+ regulator-always-on;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_exp>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_exp>;
+ regulator-always-on;
+ };
+};
+
+
+&main_pmx0 {
+ cam0_reset_pins_default: cam0-default-reset-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x03c, PIN_OUTPUT, 7) /* (R22) GPIO0_15 */
+ >;
+ };
+
+ cam1_reset_pins_default: cam1-default-reset-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x044, PIN_OUTPUT, 7) /* (R26) GPIO0_17 */
+ >;
+ };
+
+ cam2_reset_pins_default: cam2-default-reset-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x04c, PIN_OUTPUT, 7) /* (T25) GPIO0_19 */
+ >;
+ };
+
+ cam3_reset_pins_default: cam3-default-reset-pins {
+ pinctrl-single,pins = <
+ J722S_IOPAD(0x054, PIN_OUTPUT, 7) /* (T21) GPIO0_21 */
+ >;
+ };
+};
+
+&csi01_mux {
+ idle-state = <1>;
+};
+
+&csi23_mux {
+ idle-state = <1>;
+};
+
+&pca9543_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ ov5640_0: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ AVDD-supply = <®_2p8v>;
+ DOVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_3p3v>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam0_reset_pins_default>;
+
+ reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>;
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ ov5640_1: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ AVDD-supply = <®_2p8v>;
+ DOVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_3p3v>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam1_reset_pins_default>;
+
+ reset-gpios = <&main_gpio0 17 GPIO_ACTIVE_HIGH>;
+
+ port {
+ csi2_cam1: endpoint {
+ remote-endpoint = <&csi2rx1_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+};
+
+&pca9543_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ ov5640_2: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ AVDD-supply = <®_2p8v>;
+ DOVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_3p3v>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam2_reset_pins_default>;
+
+ reset-gpios = <&main_gpio0 19 GPIO_ACTIVE_HIGH>;
+
+ port {
+ csi2_cam2: endpoint {
+ remote-endpoint = <&csi2rx2_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ ov5640_3: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ AVDD-supply = <®_2p8v>;
+ DOVDD-supply = <®_1p8v>;
+ DVDD-supply = <®_3p3v>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam3_reset_pins_default>;
+
+ reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>;
+
+ port {
+ csi2_cam3: endpoint {
+ remote-endpoint = <&csi2rx3_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx1 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi1_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx1_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam1>;
+ bus-type = <4>; /* CSI2 DPHY */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx2 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi2_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx2_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam2>;
+ bus-type = <4>; /* CSI2 DPHY */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx3 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi3_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx3_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam3>;
+ bus-type = <4>; /* CSI2 DPHY */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
+
+&dphy0 {
+ status = "okay";
+};
+
+&ti_csi2rx1 {
+ status = "okay";
+};
+
+&dphy1 {
+ status = "okay";
+};
+
+
+&ti_csi2rx2 {
+ status = "okay";
+};
+
+&dphy2 {
+ status = "okay";
+};
+
+
+&ti_csi2rx3 {
+ status = "okay";
+};
+
+&dphy3 {
+ status = "okay";
+};
--
2.34.1
Powered by blists - more mailing lists