[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <c8097899-42f6-4fa6-bee1-6af9208283d7@quicinc.com>
Date: Thu, 8 May 2025 22:31:02 +0530
From: Prasad Kumpatla <quic_pkumpatl@...cinc.com>
To: Konrad Dybcio <konrad.dybcio@....qualcomm.com>,
Bjorn Andersson
<andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>, Rob Herring
<robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley
<conor+dt@...nel.org>
CC: <cros-qcom-dts-watchers@...omium.org>, <linux-arm-msm@...r.kernel.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<kernel@....qualcomm.com>, Mohammad Rafi Shaik <quic_mohs@...cinc.com>
Subject: Re: [PATCH v2 6/7] arm64: dts: qcom: qcm6490-idp: Add WSA8830
speakers and WCD9370 headset codec
On 4/29/2025 4:31 PM, Konrad Dybcio wrote:
> On 4/29/25 11:24 AM, Prasad Kumpatla wrote:
>> From: Mohammad Rafi Shaik <quic_mohs@...cinc.com>
>>
>> Add nodes for WSA8830 speakers and WCD9370 headset codec
>> on qcm6490-idp board.
>>
>> Enable lpass macros along with audio support pin controls.
>>
>> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@...cinc.com>
>> Co-developed-by: Prasad Kumpatla <quic_pkumpatl@...cinc.com>
>> Signed-off-by: Prasad Kumpatla <quic_pkumpatl@...cinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 162 +++++++++++++++++++++++
>> 1 file changed, 162 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>> index 7a155ef6492e..1a59080cbfaf 100644
>> --- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>> +++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>> @@ -18,6 +18,7 @@
>> #include "pm7325.dtsi"
>> #include "pm8350c.dtsi"
>> #include "pmk8350.dtsi"
>> +#include "qcs6490-audioreach.dtsi"
>>
>> /delete-node/ &ipa_fw_mem;
>> /delete-node/ &rmtfs_mem;
>> @@ -169,6 +170,30 @@
>> regulator-min-microvolt = <3700000>;
>> regulator-max-microvolt = <3700000>;
>> };
>> +
>> + wcd9370: audio-codec-0 {
>> + compatible = "qcom,wcd9370-codec";
>> +
>> + pinctrl-0 = <&wcd_reset_n>;
>> + pinctrl-1 = <&wcd_reset_n_sleep>;
>> + pinctrl-names = "default", "sleep";
>
> Does audio work for you? For inexplicable reasons, it didn't for me
> on rb2 when the sleep state was defined
>
For Qcm6490-IDP board Audio is working fine, Not sure about rb2, Could
you please provide more details about rb2 ?>> +
>> + reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
>> +
>> + vdd-buck-supply = <&vreg_l17b_1p7>;
>> + vdd-rxtx-supply = <&vreg_l18b_1p8>;
>> + vdd-px-supply = <&vreg_l18b_1p8>;
>> + vdd-mic-bias-supply = <&vreg_bob_3p296>;
>> +
>> + qcom,micbias1-microvolt = <1800000>;
>> + qcom,micbias2-microvolt = <1800000>;
>> + qcom,micbias3-microvolt = <1800000>;
>> +
>> + qcom,rx-device = <&wcd937x_rx>;
>> + qcom,tx-device = <&wcd937x_tx>;
>> +
>> + #sound-dai-cells = <1>;
>> + };
>> };
>>
>> &apps_rsc {
>> @@ -536,6 +561,76 @@
>> firmware-name = "qcom/qcm6490/a660_zap.mbn";
>> };
>>
>> +&lpass_dmic01_clk {
>> + drive-strength = <8>;
>> + bias-disable;
>> +};
>> +
>> +&lpass_dmic01_data {
>> + bias-pull-down;
>
> As a testament to these definitions belonging in the soc dtsi, you
> added them in the file you included already.
>
> [...]
Ack, Will move to soc dtsi file.>
>> &tlmm {
>> gpio-reserved-ranges = <32 2>, /* ADSP */
>> <48 4>; /* NFC */
>> @@ -725,6 +868,25 @@
>> function = "gpio";
>> bias-pull-up;
>> };
>> +
>> + sw_ctrl: sw-ctrl-state {
>> + pins = "gpio86";
>> + function = "gpio";
>> + bias-pull-down;
>> + };
>
> Again, unused
Ack>
>> +
>> + wcd_reset_n: wcd-reset-n-state {
>> + pins = "gpio83";
>> + function = "gpio";
>> + drive-strength = <8>;
>
> Since the definition is otherwise identical to the sleep state,
> you should define the (other) bias type that should be set when
> active.
>
Taken the reference from sc7280, which is working fine.
Link for reference :
https://elixir.bootlin.com/linux/v6.15-rc5/source/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi#L841
Will cross check and modify if required.
Thanks,
Prasad> Konrad
> > + };
>> +
>> + wcd_reset_n_sleep: wcd-reset-n-sleep-state {
>> + pins = "gpio83";
>> + function = "gpio";
>> + drive-strength = <8>;
>> + bias-disable;
>> + };
>> };
>>
>> &uart5 {
Powered by blists - more mailing lists