| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250528221823.2974653-4-joseph.kogut@gmail.com>
Date: Wed, 28 May 2025 15:18:23 -0700
From: Joseph Kogut <joseph.kogut@...il.com>
To: Heiko Stuebner <heiko@...ech.de>,
Rob Herring <robh@...nel.org>
Cc: Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
devicetree@...r.kernel.org,
linux-rockchip@...ts.infradead.org,
linux-kernel@...r.kernel.org,
Steve deRosier <derosier@...-sierra.com>,
Joseph Kogut <joseph.kogut@...il.com>
Subject: [PATCH v3 3/3] arm64: dts: rockchip: Add support for CM5 IO carrier
Specification:
- 1x HDMI
- 2x MIPI DSI
- 2x MIPI CSI
- 1x eDP
- 1x M.2 E key
- 1x USB 3.0 Host
- 1x USB 3.0 OTG
- 2x USB 2.0 Host
- Headphone jack w/ microphone
- Gigabit Ethernet w/ PoE
- microSD slot
- 40-pin expansion header
- 12V DC
Signed-off-by: Joseph Kogut <joseph.kogut@...il.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3588s-radxa-cm5-io.dts | 454 ++++++++++++++++++
2 files changed, 455 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 3e8771ef69ba..bc09420cacde 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -177,6 +177,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts b/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts
new file mode 100644
index 000000000000..28d74e390a3c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts
@@ -0,0 +1,454 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Joseph Kogut <joseph.kogut@...il.com>
+ */
+
+/*
+ * CM5 IO board data sheet
+ * https://dl.radxa.com/cm5/v2200/radxa_cm5_io_v2200_schematic.pdf
+ */
+
+/dts-v1/;
+#include "rk3588s.dtsi"
+#include "rk3588s-radxa-cm5.dtsi"
+
+/ {
+ model = "Radxa Compute Module 5 (CM5) IO Board";
+ compatible = "radxa,cm5-io", "radxa,cm5", "rockchip,rk3588s";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi0_out_con>;
+ };
+ };
+ };
+
+ vcc12v_dcin: regulator-12v0-vcc-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_host";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: regulator-5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vbus5v0_typec: vbus5v0-typec {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus5v0_typec";
+ gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vbus5v0_typec_en>;
+ enable-active-high;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie: regulator-3v3-vcc-pcie {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie2x1l0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ gpios = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy2_psu {
+ status = "okay";
+};
+
+&hdmi0_in {
+ hdmi0_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi0>;
+ };
+};
+
+&hdmi0_out {
+ hdmi0_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdptxphy0 {
+ status = "okay";
+};
+
+&i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6m3_xfer>;
+ status = "okay";
+
+ fusb302: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PC4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus5v0_typec>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "source";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+ op-sink-microwatt = <1000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_orientation_switch: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_role_switch: endpoint {
+ remote-endpoint = <&usb_host0_xhci_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ usbc0_dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "okay";
+};
+
+&pinctrl {
+ fusb302 {
+ vbus5v0_typec_en: vbus5v0-typec-en {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usbc0_int: usbc0-int {
+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <200000000>;
+ no-sdio;
+ no-mmc;
+ sd-uhs-sdr104;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det>;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&spi2 {
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ status = "okay";
+
+ pmic@0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ spi-max-frequency = <1000000>;
+ system-power-controller;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vdd2_ddr_s3>;
+ vcc14-supply = <&vdd2_ddr_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ regulators {
+ vdd_gpu_s0: dcdc-reg1 {
+ regulator-name = "vdd_gpu_s0";
+ regulator-boot-on;
+ regulator-enable-ramp-delay = <400>;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: dcdc-reg2 {
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-name = "vdd2_ddr_s3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-name = "vcc_3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+ };
+ };
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ status = "okay";
+};
+
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb_host0_xhci_role_switch: endpoint {
+ remote-endpoint = <&usbc0_role_switch>;
+ };
+ };
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orientation_switch>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc0_dp_altmode_mux>;
+ };
+ };
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi0: endpoint@...KCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi0_in_vp0>;
+ };
+};
--
2.49.0
Powered by blists - more mailing lists