| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250704182202.1641943-6-ivecera@redhat.com>
Date: Fri, 4 Jul 2025 20:21:55 +0200
From: Ivan Vecera <ivecera@...hat.com>
To: Jiri Pirko <jiri@...nulli.us>,
netdev@...r.kernel.org
Cc: Vadim Fedorenko <vadim.fedorenko@...ux.dev>,
Arkadiusz Kubalewski <arkadiusz.kubalewski@...el.com>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Prathosh Satish <Prathosh.Satish@...rochip.com>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Simon Horman <horms@...nel.org>,
Jonathan Corbet <corbet@....net>,
Jason Gunthorpe <jgg@...pe.ca>,
Shannon Nelson <shannon.nelson@....com>,
Dave Jiang <dave.jiang@...el.com>,
Jonathan Cameron <Jonathan.Cameron@...wei.com>,
devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
linux-doc@...r.kernel.org,
Michal Schmidt <mschmidt@...hat.com>,
Petr Oros <poros@...hat.com>
Subject: [PATCH net-next v13 05/12] dpll: Add basic Microchip ZL3073x support
Microchip Azurite ZL3073x represents chip family providing DPLL
and optionally PHC (PTP) functionality. The chips can be connected
be connected over I2C or SPI bus.
They have the following characteristics:
* up to 5 separate DPLL units (channels)
* 5 synthesizers
* 10 input pins (references)
* 10 outputs
* 20 output pins (output pin pair shares one output)
* Each reference and output can operate in either differential or
single-ended mode (differential mode uses 2 pins)
* Each output is connected to one of the synthesizers
* Each synthesizer is driven by one of the DPLL unit
The device uses 7-bit addresses and 8-bits values. It exposes 8-, 16-,
32- and 48-bits registers in address range <0x000,0x77F>. Due to 7bit
addressing, the range is organized into pages of 128 bytes, with each
page containing a page selector register at address 0x7F.
For reading/writing multi-byte registers, the device supports bulk
transfers.
Add basic functionality to access device registers, probe functionality
both I2C and SPI cases and add devlink support to provide info and
to set clock ID parameter.
Signed-off-by: Ivan Vecera <ivecera@...hat.com>
---
v13:
* squashed patches 4, 5 & 7
* extended Kconfig description
* renamed "cfg.custom_ver" to "custom_cfg"
* initial clock_id is generated randomly
* added support for devlink clock_id parameter
---
Documentation/networking/devlink/index.rst | 1 +
Documentation/networking/devlink/zl3073x.rst | 51 ++
MAINTAINERS | 8 +
drivers/Kconfig | 4 +-
drivers/dpll/Kconfig | 6 +
drivers/dpll/Makefile | 2 +
drivers/dpll/zl3073x/Kconfig | 38 ++
drivers/dpll/zl3073x/Makefile | 10 +
drivers/dpll/zl3073x/core.c | 465 +++++++++++++++++++
drivers/dpll/zl3073x/core.h | 57 +++
drivers/dpll/zl3073x/devlink.c | 242 ++++++++++
drivers/dpll/zl3073x/devlink.h | 12 +
drivers/dpll/zl3073x/i2c.c | 76 +++
drivers/dpll/zl3073x/regs.h | 75 +++
drivers/dpll/zl3073x/spi.c | 76 +++
15 files changed, 1121 insertions(+), 2 deletions(-)
create mode 100644 Documentation/networking/devlink/zl3073x.rst
create mode 100644 drivers/dpll/zl3073x/Kconfig
create mode 100644 drivers/dpll/zl3073x/Makefile
create mode 100644 drivers/dpll/zl3073x/core.c
create mode 100644 drivers/dpll/zl3073x/core.h
create mode 100644 drivers/dpll/zl3073x/devlink.c
create mode 100644 drivers/dpll/zl3073x/devlink.h
create mode 100644 drivers/dpll/zl3073x/i2c.c
create mode 100644 drivers/dpll/zl3073x/regs.h
create mode 100644 drivers/dpll/zl3073x/spi.c
diff --git a/Documentation/networking/devlink/index.rst b/Documentation/networking/devlink/index.rst
index 8319f43b5933d..250ae71f40236 100644
--- a/Documentation/networking/devlink/index.rst
+++ b/Documentation/networking/devlink/index.rst
@@ -98,3 +98,4 @@ parameters, info versions, and other features it supports.
iosm
octeontx2
sfc
+ zl3073x
diff --git a/Documentation/networking/devlink/zl3073x.rst b/Documentation/networking/devlink/zl3073x.rst
new file mode 100644
index 0000000000000..4b6cfaf386433
--- /dev/null
+++ b/Documentation/networking/devlink/zl3073x.rst
@@ -0,0 +1,51 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=======================
+zl3073x devlink support
+=======================
+
+This document describes the devlink features implemented by the ``zl3073x``
+device driver.
+
+Parameters
+==========
+
+.. list-table:: Generic parameters implemented
+ :widths: 5 5 90
+
+ * - Name
+ - Mode
+ - Notes
+ * - ``clock_id``
+ - driverinit
+ - Set the clock ID that is used by the driver for registering DPLL devices
+ and pins.
+
+Info versions
+=============
+
+The ``zl3073x`` driver reports the following versions
+
+.. list-table:: devlink info versions implemented
+ :widths: 5 5 5 90
+
+ * - Name
+ - Type
+ - Example
+ - Description
+ * - ``asic.id``
+ - fixed
+ - 1E94
+ - Chip identification number
+ * - ``asic.rev``
+ - fixed
+ - 300
+ - Chip revision number
+ * - ``fw``
+ - running
+ - 7006
+ - Firmware version number
+ * - ``custom_cfg``
+ - running
+ - 1.3.0.1
+ - Device configuration version customized by OEM
diff --git a/MAINTAINERS b/MAINTAINERS
index 5488a6fd31f59..b841cdb568306 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16479,6 +16479,14 @@ L: linux-wireless@...r.kernel.org
S: Supported
F: drivers/net/wireless/microchip/
+MICROCHIP ZL3073X DRIVER
+M: Ivan Vecera <ivecera@...hat.com>
+M: Prathosh Satish <Prathosh.Satish@...rochip.com>
+L: netdev@...r.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/dpll/microchip,zl30731.yaml
+F: drivers/dpll/zl3073x/
+
MICROSEMI MIPS SOCS
M: Alexandre Belloni <alexandre.belloni@...tlin.com>
M: UNGLinuxDriver@...rochip.com
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 7c556c5ac4fdd..3d8c902c25610 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -77,6 +77,8 @@ source "drivers/pps/Kconfig"
source "drivers/ptp/Kconfig"
+source "drivers/dpll/Kconfig"
+
source "drivers/pinctrl/Kconfig"
source "drivers/gpio/Kconfig"
@@ -245,6 +247,4 @@ source "drivers/hte/Kconfig"
source "drivers/cdx/Kconfig"
-source "drivers/dpll/Kconfig"
-
endmenu
diff --git a/drivers/dpll/Kconfig b/drivers/dpll/Kconfig
index 20607ed542435..ade872c915ac6 100644
--- a/drivers/dpll/Kconfig
+++ b/drivers/dpll/Kconfig
@@ -3,5 +3,11 @@
# Generic DPLL drivers configuration
#
+menu "DPLL device support"
+
config DPLL
bool
+
+source "drivers/dpll/zl3073x/Kconfig"
+
+endmenu
diff --git a/drivers/dpll/Makefile b/drivers/dpll/Makefile
index 2e5b278501105..9e7a3a3e592e8 100644
--- a/drivers/dpll/Makefile
+++ b/drivers/dpll/Makefile
@@ -7,3 +7,5 @@ obj-$(CONFIG_DPLL) += dpll.o
dpll-y += dpll_core.o
dpll-y += dpll_netlink.o
dpll-y += dpll_nl.o
+
+obj-$(CONFIG_ZL3073X) += zl3073x/
diff --git a/drivers/dpll/zl3073x/Kconfig b/drivers/dpll/zl3073x/Kconfig
new file mode 100644
index 0000000000000..41fa6a8f96ab9
--- /dev/null
+++ b/drivers/dpll/zl3073x/Kconfig
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+config ZL3073X
+ tristate "Microchip Azurite DPLL/PTP/SyncE devices"
+ depends on NET
+ select DPLL
+ select NET_DEVLINK
+ help
+ This driver supports Microchip Azurite family DPLL/PTP/SyncE
+ devices that support up to 5 independent DPLL channels,
+ 10 input pins and up to 20 output pins.
+
+ To compile this driver as a module, choose M here. The module
+ will be called zl3073x.
+
+config ZL3073X_I2C
+ tristate "I2C bus implementation for Microchip Azurite devices"
+ depends on I2C && ZL3073X
+ select REGMAP_I2C
+ default m
+ help
+ This is I2C bus implementation for Microchip Azurite DPLL/PTP/SyncE
+ devices.
+
+ To compile this driver as a module, choose M here: the module will
+ be called zl3073x_i2c.
+
+config ZL3073X_SPI
+ tristate "SPI bus implementation for Microchip Azurite devices"
+ depends on SPI && ZL3073X
+ select REGMAP_SPI
+ default m
+ help
+ This is SPI bus implementation for Microchip Azurite DPLL/PTP/SyncE
+ devices.
+
+ To compile this driver as a module, choose M here: the module will
+ be called zl3073x_spi.
diff --git a/drivers/dpll/zl3073x/Makefile b/drivers/dpll/zl3073x/Makefile
new file mode 100644
index 0000000000000..ef2c575ce012c
--- /dev/null
+++ b/drivers/dpll/zl3073x/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_ZL3073X) += zl3073x.o
+zl3073x-objs := core.o devlink.o
+
+obj-$(CONFIG_ZL3073X_I2C) += zl3073x_i2c.o
+zl3073x_i2c-objs := i2c.o
+
+obj-$(CONFIG_ZL3073X_SPI) += zl3073x_spi.o
+zl3073x_spi-objs := spi.o
diff --git a/drivers/dpll/zl3073x/core.c b/drivers/dpll/zl3073x/core.c
new file mode 100644
index 0000000000000..38019f878ff02
--- /dev/null
+++ b/drivers/dpll/zl3073x/core.c
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/array_size.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/dev_printk.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/module.h>
+#include <linux/netlink.h>
+#include <linux/regmap.h>
+#include <linux/sprintf.h>
+#include <linux/unaligned.h>
+#include <net/devlink.h>
+
+#include "core.h"
+#include "devlink.h"
+#include "regs.h"
+
+/* Chip IDs for zl30731 */
+static const u16 zl30731_ids[] = {
+ 0x0E93,
+ 0x1E93,
+ 0x2E93,
+};
+
+const struct zl3073x_chip_info zl30731_chip_info = {
+ .ids = zl30731_ids,
+ .num_ids = ARRAY_SIZE(zl30731_ids),
+ .num_channels = 1,
+};
+EXPORT_SYMBOL_NS_GPL(zl30731_chip_info, "ZL3073X");
+
+/* Chip IDs for zl30732 */
+static const u16 zl30732_ids[] = {
+ 0x0E30,
+ 0x0E94,
+ 0x1E94,
+ 0x1F60,
+ 0x2E94,
+ 0x3FC4,
+};
+
+const struct zl3073x_chip_info zl30732_chip_info = {
+ .ids = zl30732_ids,
+ .num_ids = ARRAY_SIZE(zl30732_ids),
+ .num_channels = 2,
+};
+EXPORT_SYMBOL_NS_GPL(zl30732_chip_info, "ZL3073X");
+
+/* Chip IDs for zl30733 */
+static const u16 zl30733_ids[] = {
+ 0x0E95,
+ 0x1E95,
+ 0x2E95,
+};
+
+const struct zl3073x_chip_info zl30733_chip_info = {
+ .ids = zl30733_ids,
+ .num_ids = ARRAY_SIZE(zl30733_ids),
+ .num_channels = 3,
+};
+EXPORT_SYMBOL_NS_GPL(zl30733_chip_info, "ZL3073X");
+
+/* Chip IDs for zl30734 */
+static const u16 zl30734_ids[] = {
+ 0x0E96,
+ 0x1E96,
+ 0x2E96,
+};
+
+const struct zl3073x_chip_info zl30734_chip_info = {
+ .ids = zl30734_ids,
+ .num_ids = ARRAY_SIZE(zl30734_ids),
+ .num_channels = 4,
+};
+EXPORT_SYMBOL_NS_GPL(zl30734_chip_info, "ZL3073X");
+
+/* Chip IDs for zl30735 */
+static const u16 zl30735_ids[] = {
+ 0x0E97,
+ 0x1E97,
+ 0x2E97,
+};
+
+const struct zl3073x_chip_info zl30735_chip_info = {
+ .ids = zl30735_ids,
+ .num_ids = ARRAY_SIZE(zl30735_ids),
+ .num_channels = 5,
+};
+EXPORT_SYMBOL_NS_GPL(zl30735_chip_info, "ZL3073X");
+
+#define ZL_RANGE_OFFSET 0x80
+#define ZL_PAGE_SIZE 0x80
+#define ZL_NUM_PAGES 15
+#define ZL_PAGE_SEL 0x7F
+#define ZL_PAGE_SEL_MASK GENMASK(3, 0)
+#define ZL_NUM_REGS (ZL_NUM_PAGES * ZL_PAGE_SIZE)
+
+/* Regmap range configuration */
+static const struct regmap_range_cfg zl3073x_regmap_range = {
+ .range_min = ZL_RANGE_OFFSET,
+ .range_max = ZL_RANGE_OFFSET + ZL_NUM_REGS - 1,
+ .selector_reg = ZL_PAGE_SEL,
+ .selector_mask = ZL_PAGE_SEL_MASK,
+ .selector_shift = 0,
+ .window_start = 0,
+ .window_len = ZL_PAGE_SIZE,
+};
+
+static bool
+zl3073x_is_volatile_reg(struct device *dev __maybe_unused, unsigned int reg)
+{
+ /* Only page selector is non-volatile */
+ return reg != ZL_PAGE_SEL;
+}
+
+const struct regmap_config zl3073x_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = ZL_RANGE_OFFSET + ZL_NUM_REGS - 1,
+ .ranges = &zl3073x_regmap_range,
+ .num_ranges = 1,
+ .cache_type = REGCACHE_MAPLE,
+ .volatile_reg = zl3073x_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS_GPL(zl3073x_regmap_config, "ZL3073X");
+
+static bool
+zl3073x_check_reg(struct zl3073x_dev *zldev, unsigned int reg, size_t size)
+{
+ /* Check that multiop lock is held when accessing registers
+ * from page 10 and above.
+ */
+ if (ZL_REG_PAGE(reg) >= 10)
+ lockdep_assert_held(&zldev->multiop_lock);
+
+ /* Check the index is in valid range for indexed register */
+ if (ZL_REG_OFFSET(reg) > ZL_REG_MAX_OFFSET(reg)) {
+ dev_err(zldev->dev, "Index out of range for reg 0x%04lx\n",
+ ZL_REG_ADDR(reg));
+ return false;
+ }
+ /* Check the requested size corresponds to register size */
+ if (ZL_REG_SIZE(reg) != size) {
+ dev_err(zldev->dev, "Invalid size %zu for reg 0x%04lx\n",
+ size, ZL_REG_ADDR(reg));
+ return false;
+ }
+
+ return true;
+}
+
+static int
+zl3073x_read_reg(struct zl3073x_dev *zldev, unsigned int reg, void *val,
+ size_t size)
+{
+ int rc;
+
+ if (!zl3073x_check_reg(zldev, reg, size))
+ return -EINVAL;
+
+ /* Map the register address to virtual range */
+ reg = ZL_REG_ADDR(reg) + ZL_RANGE_OFFSET;
+
+ rc = regmap_bulk_read(zldev->regmap, reg, val, size);
+ if (rc) {
+ dev_err(zldev->dev, "Failed to read reg 0x%04x: %pe\n", reg,
+ ERR_PTR(rc));
+ return rc;
+ }
+
+ return 0;
+}
+
+static int
+zl3073x_write_reg(struct zl3073x_dev *zldev, unsigned int reg, const void *val,
+ size_t size)
+{
+ int rc;
+
+ if (!zl3073x_check_reg(zldev, reg, size))
+ return -EINVAL;
+
+ /* Map the register address to virtual range */
+ reg = ZL_REG_ADDR(reg) + ZL_RANGE_OFFSET;
+
+ rc = regmap_bulk_write(zldev->regmap, reg, val, size);
+ if (rc) {
+ dev_err(zldev->dev, "Failed to write reg 0x%04x: %pe\n", reg,
+ ERR_PTR(rc));
+ return rc;
+ }
+
+ return 0;
+}
+
+/**
+ * zl3073x_read_u8 - read value from 8bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Reads value from given 8bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_read_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 *val)
+{
+ return zl3073x_read_reg(zldev, reg, val, sizeof(*val));
+}
+
+/**
+ * zl3073x_write_u8 - write value to 16bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Writes value into given 8bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_write_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 val)
+{
+ return zl3073x_write_reg(zldev, reg, &val, sizeof(val));
+}
+
+/**
+ * zl3073x_read_u16 - read value from 16bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Reads value from given 16bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_read_u16(struct zl3073x_dev *zldev, unsigned int reg, u16 *val)
+{
+ int rc;
+
+ rc = zl3073x_read_reg(zldev, reg, val, sizeof(*val));
+ if (!rc)
+ be16_to_cpus(val);
+
+ return rc;
+}
+
+/**
+ * zl3073x_write_u16 - write value to 16bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Writes value into given 16bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_write_u16(struct zl3073x_dev *zldev, unsigned int reg, u16 val)
+{
+ cpu_to_be16s(&val);
+
+ return zl3073x_write_reg(zldev, reg, &val, sizeof(val));
+}
+
+/**
+ * zl3073x_read_u32 - read value from 32bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Reads value from given 32bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_read_u32(struct zl3073x_dev *zldev, unsigned int reg, u32 *val)
+{
+ int rc;
+
+ rc = zl3073x_read_reg(zldev, reg, val, sizeof(*val));
+ if (!rc)
+ be32_to_cpus(val);
+
+ return rc;
+}
+
+/**
+ * zl3073x_write_u32 - write value to 32bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Writes value into given 32bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_write_u32(struct zl3073x_dev *zldev, unsigned int reg, u32 val)
+{
+ cpu_to_be32s(&val);
+
+ return zl3073x_write_reg(zldev, reg, &val, sizeof(val));
+}
+
+/**
+ * zl3073x_read_u48 - read value from 48bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Reads value from given 48bit register.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_read_u48(struct zl3073x_dev *zldev, unsigned int reg, u64 *val)
+{
+ u8 buf[6];
+ int rc;
+
+ rc = zl3073x_read_reg(zldev, reg, buf, sizeof(buf));
+ if (!rc)
+ *val = get_unaligned_be48(buf);
+
+ return rc;
+}
+
+/**
+ * zl3073x_write_u48 - write value to 48bit register
+ * @zldev: zl3073x device pointer
+ * @reg: register to write to
+ * @val: value to write
+ *
+ * Writes value into given 48bit register.
+ * The value must be from the interval -S48_MIN to U48_MAX.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_write_u48(struct zl3073x_dev *zldev, unsigned int reg, u64 val)
+{
+ u8 buf[6];
+
+ /* Check the value belongs to <S48_MIN, U48_MAX>
+ * Any value >= S48_MIN has bits 47..63 set.
+ */
+ if (val > GENMASK_ULL(47, 0) && val < GENMASK_ULL(63, 47)) {
+ dev_err(zldev->dev, "Value 0x%0llx out of range\n", val);
+ return -EINVAL;
+ }
+
+ put_unaligned_be48(val, buf);
+
+ return zl3073x_write_reg(zldev, reg, buf, sizeof(buf));
+}
+
+/**
+ * zl3073x_poll_zero_u8 - wait for register to be cleared by device
+ * @zldev: zl3073x device pointer
+ * @reg: register to poll (has to be 8bit register)
+ * @mask: bit mask for polling
+ *
+ * Waits for bits specified by @mask in register @reg value to be cleared
+ * by the device.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_poll_zero_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 mask)
+{
+ /* Register polling sleep & timeout */
+#define ZL_POLL_SLEEP_US 10
+#define ZL_POLL_TIMEOUT_US 2000000
+ unsigned int val;
+
+ /* Check the register is 8bit */
+ if (ZL_REG_SIZE(reg) != 1) {
+ dev_err(zldev->dev, "Invalid reg 0x%04lx size for polling\n",
+ ZL_REG_ADDR(reg));
+ return -EINVAL;
+ }
+
+ /* Map the register address to virtual range */
+ reg = ZL_REG_ADDR(reg) + ZL_RANGE_OFFSET;
+
+ return regmap_read_poll_timeout(zldev->regmap, reg, val, !(val & mask),
+ ZL_POLL_SLEEP_US, ZL_POLL_TIMEOUT_US);
+}
+
+/**
+ * zl3073x_dev_probe - initialize zl3073x device
+ * @zldev: pointer to zl3073x device
+ * @chip_info: chip info based on compatible
+ *
+ * Common initialization of zl3073x device structure.
+ *
+ * Returns: 0 on success, <0 on error
+ */
+int zl3073x_dev_probe(struct zl3073x_dev *zldev,
+ const struct zl3073x_chip_info *chip_info)
+{
+ u16 id, revision, fw_ver;
+ unsigned int i;
+ u32 cfg_ver;
+ int rc;
+
+ /* Read chip ID */
+ rc = zl3073x_read_u16(zldev, ZL_REG_ID, &id);
+ if (rc)
+ return rc;
+
+ /* Check it matches */
+ for (i = 0; i < chip_info->num_ids; i++) {
+ if (id == chip_info->ids[i])
+ break;
+ }
+
+ if (i == chip_info->num_ids) {
+ return dev_err_probe(zldev->dev, -ENODEV,
+ "Unknown or non-match chip ID: 0x%0x\n",
+ id);
+ }
+
+ /* Read revision, firmware version and custom config version */
+ rc = zl3073x_read_u16(zldev, ZL_REG_REVISION, &revision);
+ if (rc)
+ return rc;
+ rc = zl3073x_read_u16(zldev, ZL_REG_FW_VER, &fw_ver);
+ if (rc)
+ return rc;
+ rc = zl3073x_read_u32(zldev, ZL_REG_CUSTOM_CONFIG_VER, &cfg_ver);
+ if (rc)
+ return rc;
+
+ dev_dbg(zldev->dev, "ChipID(%X), ChipRev(%X), FwVer(%u)\n", id,
+ revision, fw_ver);
+ dev_dbg(zldev->dev, "Custom config version: %lu.%lu.%lu.%lu\n",
+ FIELD_GET(GENMASK(31, 24), cfg_ver),
+ FIELD_GET(GENMASK(23, 16), cfg_ver),
+ FIELD_GET(GENMASK(15, 8), cfg_ver),
+ FIELD_GET(GENMASK(7, 0), cfg_ver));
+
+ /* Generate random clock ID as the device has not such property that
+ * could be used for this purpose. A user can later change this value
+ * using devlink.
+ */
+ zldev->clock_id = get_random_u64();
+
+ /* Initialize mutex for operations where multiple reads, writes
+ * and/or polls are required to be done atomically.
+ */
+ rc = devm_mutex_init(zldev->dev, &zldev->multiop_lock);
+ if (rc)
+ return dev_err_probe(zldev->dev, rc,
+ "Failed to initialize mutex\n");
+
+ /* Register the devlink instance and parameters */
+ rc = zl3073x_devlink_register(zldev);
+ if (rc)
+ return dev_err_probe(zldev->dev, rc,
+ "Failed to register devlink instance\n");
+
+ return 0;
+}
+EXPORT_SYMBOL_NS_GPL(zl3073x_dev_probe, "ZL3073X");
+
+MODULE_AUTHOR("Ivan Vecera <ivecera@...hat.com>");
+MODULE_DESCRIPTION("Microchip ZL3073x core driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/dpll/zl3073x/core.h b/drivers/dpll/zl3073x/core.h
new file mode 100644
index 0000000000000..d5e7b1977b161
--- /dev/null
+++ b/drivers/dpll/zl3073x/core.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _ZL3073X_CORE_H
+#define _ZL3073X_CORE_H
+
+#include <linux/mutex.h>
+#include <linux/types.h>
+
+struct device;
+struct regmap;
+
+/**
+ * struct zl3073x_dev - zl3073x device
+ * @dev: pointer to device
+ * @regmap: regmap to access device registers
+ * @multiop_lock: to serialize multiple register operations
+ * @clock_id: clock id of the device
+ */
+struct zl3073x_dev {
+ struct device *dev;
+ struct regmap *regmap;
+ struct mutex multiop_lock;
+ u64 clock_id;
+};
+
+struct zl3073x_chip_info {
+ const u16 *ids;
+ size_t num_ids;
+ int num_channels;
+};
+
+extern const struct zl3073x_chip_info zl30731_chip_info;
+extern const struct zl3073x_chip_info zl30732_chip_info;
+extern const struct zl3073x_chip_info zl30733_chip_info;
+extern const struct zl3073x_chip_info zl30734_chip_info;
+extern const struct zl3073x_chip_info zl30735_chip_info;
+extern const struct regmap_config zl3073x_regmap_config;
+
+struct zl3073x_dev *zl3073x_devm_alloc(struct device *dev);
+int zl3073x_dev_probe(struct zl3073x_dev *zldev,
+ const struct zl3073x_chip_info *chip_info);
+
+/**********************
+ * Registers operations
+ **********************/
+
+int zl3073x_poll_zero_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 mask);
+int zl3073x_read_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 *val);
+int zl3073x_read_u16(struct zl3073x_dev *zldev, unsigned int reg, u16 *val);
+int zl3073x_read_u32(struct zl3073x_dev *zldev, unsigned int reg, u32 *val);
+int zl3073x_read_u48(struct zl3073x_dev *zldev, unsigned int reg, u64 *val);
+int zl3073x_write_u8(struct zl3073x_dev *zldev, unsigned int reg, u8 val);
+int zl3073x_write_u16(struct zl3073x_dev *zldev, unsigned int reg, u16 val);
+int zl3073x_write_u32(struct zl3073x_dev *zldev, unsigned int reg, u32 val);
+int zl3073x_write_u48(struct zl3073x_dev *zldev, unsigned int reg, u64 val);
+
+#endif /* _ZL3073X_CORE_H */
diff --git a/drivers/dpll/zl3073x/devlink.c b/drivers/dpll/zl3073x/devlink.c
new file mode 100644
index 0000000000000..8957ab8389c4e
--- /dev/null
+++ b/drivers/dpll/zl3073x/devlink.c
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/device/devres.h>
+#include <linux/netlink.h>
+#include <linux/sprintf.h>
+#include <linux/types.h>
+#include <net/devlink.h>
+
+#include "core.h"
+#include "devlink.h"
+#include "regs.h"
+
+/**
+ * zl3073x_devlink_info_get - Devlink device info callback
+ * @devlink: devlink structure pointer
+ * @req: devlink request pointer to store information
+ * @extack: netlink extack pointer to report errors
+ *
+ * Return: 0 on success, <0 on error
+ */
+static int
+zl3073x_devlink_info_get(struct devlink *devlink, struct devlink_info_req *req,
+ struct netlink_ext_ack *extack)
+{
+ struct zl3073x_dev *zldev = devlink_priv(devlink);
+ u16 id, revision, fw_ver;
+ char buf[16];
+ u32 cfg_ver;
+ int rc;
+
+ rc = zl3073x_read_u16(zldev, ZL_REG_ID, &id);
+ if (rc)
+ return rc;
+
+ snprintf(buf, sizeof(buf), "%X", id);
+ rc = devlink_info_version_fixed_put(req,
+ DEVLINK_INFO_VERSION_GENERIC_ASIC_ID,
+ buf);
+ if (rc)
+ return rc;
+
+ rc = zl3073x_read_u16(zldev, ZL_REG_REVISION, &revision);
+ if (rc)
+ return rc;
+
+ snprintf(buf, sizeof(buf), "%X", revision);
+ rc = devlink_info_version_fixed_put(req,
+ DEVLINK_INFO_VERSION_GENERIC_ASIC_REV,
+ buf);
+ if (rc)
+ return rc;
+
+ rc = zl3073x_read_u16(zldev, ZL_REG_FW_VER, &fw_ver);
+ if (rc)
+ return rc;
+
+ snprintf(buf, sizeof(buf), "%u", fw_ver);
+ rc = devlink_info_version_running_put(req,
+ DEVLINK_INFO_VERSION_GENERIC_FW,
+ buf);
+ if (rc)
+ return rc;
+
+ rc = zl3073x_read_u32(zldev, ZL_REG_CUSTOM_CONFIG_VER, &cfg_ver);
+ if (rc)
+ return rc;
+
+ /* No custom config version */
+ if (cfg_ver == U32_MAX)
+ return 0;
+
+ snprintf(buf, sizeof(buf), "%lu.%lu.%lu.%lu",
+ FIELD_GET(GENMASK(31, 24), cfg_ver),
+ FIELD_GET(GENMASK(23, 16), cfg_ver),
+ FIELD_GET(GENMASK(15, 8), cfg_ver),
+ FIELD_GET(GENMASK(7, 0), cfg_ver));
+
+ return devlink_info_version_running_put(req, "custom_cfg", buf);
+}
+
+static int
+zl3073x_devlink_reload_down(struct devlink *devlink, bool netns_change,
+ enum devlink_reload_action action,
+ enum devlink_reload_limit limit,
+ struct netlink_ext_ack *extack)
+{
+ if (action != DEVLINK_RELOAD_ACTION_DRIVER_REINIT)
+ return -EOPNOTSUPP;
+
+ return 0;
+}
+
+static int
+zl3073x_devlink_reload_up(struct devlink *devlink,
+ enum devlink_reload_action action,
+ enum devlink_reload_limit limit,
+ u32 *actions_performed,
+ struct netlink_ext_ack *extack)
+{
+ struct zl3073x_dev *zldev = devlink_priv(devlink);
+ union devlink_param_value val;
+ int rc;
+
+ if (action != DEVLINK_RELOAD_ACTION_DRIVER_REINIT)
+ return -EOPNOTSUPP;
+
+ rc = devl_param_driverinit_value_get(devlink,
+ DEVLINK_PARAM_GENERIC_ID_CLOCK_ID,
+ &val);
+ if (rc)
+ return rc;
+
+ if (zldev->clock_id != val.vu64) {
+ dev_dbg(zldev->dev,
+ "'clock_id' changed to %016llx\n", val.vu64);
+ zldev->clock_id = val.vu64;
+ }
+
+ *actions_performed = BIT(DEVLINK_RELOAD_ACTION_DRIVER_REINIT);
+
+ return 0;
+}
+
+static const struct devlink_ops zl3073x_devlink_ops = {
+ .info_get = zl3073x_devlink_info_get,
+ .reload_actions = BIT(DEVLINK_RELOAD_ACTION_DRIVER_REINIT),
+ .reload_down = zl3073x_devlink_reload_down,
+ .reload_up = zl3073x_devlink_reload_up,
+};
+
+static void
+zl3073x_devlink_free(void *ptr)
+{
+ devlink_free(ptr);
+}
+
+/**
+ * zl3073x_devm_alloc - allocates zl3073x device structure
+ * @dev: pointer to device structure
+ *
+ * Allocates zl3073x device structure as device resource.
+ *
+ * Return: pointer to zl3073x device on success, error pointer on error
+ */
+struct zl3073x_dev *zl3073x_devm_alloc(struct device *dev)
+{
+ struct zl3073x_dev *zldev;
+ struct devlink *devlink;
+ int rc;
+
+ devlink = devlink_alloc(&zl3073x_devlink_ops, sizeof(*zldev), dev);
+ if (!devlink)
+ return ERR_PTR(-ENOMEM);
+
+ /* Add devres action to free devlink device */
+ rc = devm_add_action_or_reset(dev, zl3073x_devlink_free, devlink);
+ if (rc)
+ return ERR_PTR(rc);
+
+ zldev = devlink_priv(devlink);
+ zldev->dev = dev;
+ dev_set_drvdata(zldev->dev, zldev);
+
+ return zldev;
+}
+EXPORT_SYMBOL_NS_GPL(zl3073x_devm_alloc, "ZL3073X");
+
+static int
+zl3073x_devlink_param_clock_id_validate(struct devlink *devlink, u32 id,
+ union devlink_param_value val,
+ struct netlink_ext_ack *extack)
+{
+ if (!val.vu64) {
+ NL_SET_ERR_MSG_MOD(extack, "'clock_id' must be non-zero");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct devlink_param zl3073x_devlink_params[] = {
+ DEVLINK_PARAM_GENERIC(CLOCK_ID, BIT(DEVLINK_PARAM_CMODE_DRIVERINIT),
+ NULL, NULL,
+ zl3073x_devlink_param_clock_id_validate),
+};
+
+static void
+zl3073x_devlink_unregister(void *ptr)
+{
+ struct devlink *devlink = priv_to_devlink(ptr);
+
+ devl_lock(devlink);
+
+ /* Unregister devlink params */
+ devl_params_unregister(devlink, zl3073x_devlink_params,
+ ARRAY_SIZE(zl3073x_devlink_params));
+
+ /* Unregister devlink instance */
+ devl_unregister(devlink);
+
+ devl_unlock(devlink);
+}
+
+/**
+ * zl3073x_devlink_register - register devlink instance and params
+ * @zldev: zl3073x device to register the devlink for
+ *
+ * Register the devlink instance and parameters associated with the device.
+ *
+ * Return: 0 on success, <0 on error
+ */
+int zl3073x_devlink_register(struct zl3073x_dev *zldev)
+{
+ struct devlink *devlink = priv_to_devlink(zldev);
+ union devlink_param_value value;
+ int rc;
+
+ devl_lock(devlink);
+
+ /* Register devlink params */
+ rc = devl_params_register(devlink, zl3073x_devlink_params,
+ ARRAY_SIZE(zl3073x_devlink_params));
+ if (rc) {
+ devl_unlock(devlink);
+
+ return rc;
+ }
+
+ value.vu64 = zldev->clock_id;
+ devl_param_driverinit_value_set(devlink,
+ DEVLINK_PARAM_GENERIC_ID_CLOCK_ID,
+ value);
+
+ /* Register devlink instance */
+ devl_register(devlink);
+
+ devl_unlock(devlink);
+
+ /* Add devres action to unregister devlink device */
+ return devm_add_action_or_reset(zldev->dev, zl3073x_devlink_unregister,
+ zldev);
+}
diff --git a/drivers/dpll/zl3073x/devlink.h b/drivers/dpll/zl3073x/devlink.h
new file mode 100644
index 0000000000000..037720db204fc
--- /dev/null
+++ b/drivers/dpll/zl3073x/devlink.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _ZL3073X_DEVLINK_H
+#define _ZL3073X_DEVLINK_H
+
+struct zl3073x_dev;
+
+struct zl3073x_dev *zl3073x_devm_alloc(struct device *dev);
+
+int zl3073x_devlink_register(struct zl3073x_dev *zldev);
+
+#endif /* _ZL3073X_DEVLINK_H */
diff --git a/drivers/dpll/zl3073x/i2c.c b/drivers/dpll/zl3073x/i2c.c
new file mode 100644
index 0000000000000..7bbfdd4ed8671
--- /dev/null
+++ b/drivers/dpll/zl3073x/i2c.c
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "core.h"
+
+static int zl3073x_i2c_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct zl3073x_dev *zldev;
+
+ zldev = zl3073x_devm_alloc(dev);
+ if (IS_ERR(zldev))
+ return PTR_ERR(zldev);
+
+ zldev->regmap = devm_regmap_init_i2c(client, &zl3073x_regmap_config);
+ if (IS_ERR(zldev->regmap))
+ return dev_err_probe(dev, PTR_ERR(zldev->regmap),
+ "Failed to initialize regmap\n");
+
+ return zl3073x_dev_probe(zldev, i2c_get_match_data(client));
+}
+
+static const struct i2c_device_id zl3073x_i2c_id[] = {
+ {
+ .name = "zl30731",
+ .driver_data = (kernel_ulong_t)&zl30731_chip_info,
+ },
+ {
+ .name = "zl30732",
+ .driver_data = (kernel_ulong_t)&zl30732_chip_info,
+ },
+ {
+ .name = "zl30733",
+ .driver_data = (kernel_ulong_t)&zl30733_chip_info,
+ },
+ {
+ .name = "zl30734",
+ .driver_data = (kernel_ulong_t)&zl30734_chip_info,
+ },
+ {
+ .name = "zl30735",
+ .driver_data = (kernel_ulong_t)&zl30735_chip_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, zl3073x_i2c_id);
+
+static const struct of_device_id zl3073x_i2c_of_match[] = {
+ { .compatible = "microchip,zl30731", .data = &zl30731_chip_info },
+ { .compatible = "microchip,zl30732", .data = &zl30732_chip_info },
+ { .compatible = "microchip,zl30733", .data = &zl30733_chip_info },
+ { .compatible = "microchip,zl30734", .data = &zl30734_chip_info },
+ { .compatible = "microchip,zl30735", .data = &zl30735_chip_info },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, zl3073x_i2c_of_match);
+
+static struct i2c_driver zl3073x_i2c_driver = {
+ .driver = {
+ .name = "zl3073x-i2c",
+ .of_match_table = zl3073x_i2c_of_match,
+ },
+ .probe = zl3073x_i2c_probe,
+ .id_table = zl3073x_i2c_id,
+};
+module_i2c_driver(zl3073x_i2c_driver);
+
+MODULE_AUTHOR("Ivan Vecera <ivecera@...hat.com>");
+MODULE_DESCRIPTION("Microchip ZL3073x I2C driver");
+MODULE_IMPORT_NS("ZL3073X");
+MODULE_LICENSE("GPL");
diff --git a/drivers/dpll/zl3073x/regs.h b/drivers/dpll/zl3073x/regs.h
new file mode 100644
index 0000000000000..08bf595935ea1
--- /dev/null
+++ b/drivers/dpll/zl3073x/regs.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _ZL3073X_REGS_H
+#define _ZL3073X_REGS_H
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+
+/*
+ * Register address structure:
+ * ===========================
+ * 25 19 18 16 15 7 6 0
+ * +------------------------------------------+
+ * | max_offset | size | page | page_offset |
+ * +------------------------------------------+
+ *
+ * page_offset ... <0x00..0x7F>
+ * page .......... HW page number
+ * size .......... register byte size (1, 2, 4 or 6)
+ * max_offset .... maximal offset for indexed registers
+ * (for non-indexed regs max_offset == page_offset)
+ */
+
+#define ZL_REG_OFFSET_MASK GENMASK(6, 0)
+#define ZL_REG_PAGE_MASK GENMASK(15, 7)
+#define ZL_REG_SIZE_MASK GENMASK(18, 16)
+#define ZL_REG_MAX_OFFSET_MASK GENMASK(25, 19)
+#define ZL_REG_ADDR_MASK GENMASK(15, 0)
+
+#define ZL_REG_OFFSET(_reg) FIELD_GET(ZL_REG_OFFSET_MASK, _reg)
+#define ZL_REG_PAGE(_reg) FIELD_GET(ZL_REG_PAGE_MASK, _reg)
+#define ZL_REG_MAX_OFFSET(_reg) FIELD_GET(ZL_REG_MAX_OFFSET_MASK, _reg)
+#define ZL_REG_SIZE(_reg) FIELD_GET(ZL_REG_SIZE_MASK, _reg)
+#define ZL_REG_ADDR(_reg) FIELD_GET(ZL_REG_ADDR_MASK, _reg)
+
+/**
+ * ZL_REG_IDX - define indexed register
+ * @_idx: index of register to access
+ * @_page: register page
+ * @_offset: register offset in page
+ * @_size: register byte size (1, 2, 4 or 6)
+ * @_items: number of register indices
+ * @_stride: stride between items in bytes
+ *
+ * All parameters except @_idx should be constant.
+ */
+#define ZL_REG_IDX(_idx, _page, _offset, _size, _items, _stride) \
+ (FIELD_PREP(ZL_REG_OFFSET_MASK, \
+ (_offset) + (_idx) * (_stride)) | \
+ FIELD_PREP_CONST(ZL_REG_PAGE_MASK, _page) | \
+ FIELD_PREP_CONST(ZL_REG_SIZE_MASK, _size) | \
+ FIELD_PREP_CONST(ZL_REG_MAX_OFFSET_MASK, \
+ (_offset) + ((_items) - 1) * (_stride)))
+
+/**
+ * ZL_REG - define simple (non-indexed) register
+ * @_page: register page
+ * @_offset: register offset in page
+ * @_size: register byte size (1, 2, 4 or 6)
+ *
+ * All parameters should be constant.
+ */
+#define ZL_REG(_page, _offset, _size) \
+ ZL_REG_IDX(0, _page, _offset, _size, 1, 0)
+
+/**************************
+ * Register Page 0, General
+ **************************/
+
+#define ZL_REG_ID ZL_REG(0, 0x01, 2)
+#define ZL_REG_REVISION ZL_REG(0, 0x03, 2)
+#define ZL_REG_FW_VER ZL_REG(0, 0x05, 2)
+#define ZL_REG_CUSTOM_CONFIG_VER ZL_REG(0, 0x07, 4)
+
+#endif /* _ZL3073X_REGS_H */
diff --git a/drivers/dpll/zl3073x/spi.c b/drivers/dpll/zl3073x/spi.c
new file mode 100644
index 0000000000000..af901b4d6dda0
--- /dev/null
+++ b/drivers/dpll/zl3073x/spi.c
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+#include "core.h"
+
+static int zl3073x_spi_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct zl3073x_dev *zldev;
+
+ zldev = zl3073x_devm_alloc(dev);
+ if (IS_ERR(zldev))
+ return PTR_ERR(zldev);
+
+ zldev->regmap = devm_regmap_init_spi(spi, &zl3073x_regmap_config);
+ if (IS_ERR(zldev->regmap))
+ return dev_err_probe(dev, PTR_ERR(zldev->regmap),
+ "Failed to initialize regmap\n");
+
+ return zl3073x_dev_probe(zldev, spi_get_device_match_data(spi));
+}
+
+static const struct spi_device_id zl3073x_spi_id[] = {
+ {
+ .name = "zl30731",
+ .driver_data = (kernel_ulong_t)&zl30731_chip_info
+ },
+ {
+ .name = "zl30732",
+ .driver_data = (kernel_ulong_t)&zl30732_chip_info,
+ },
+ {
+ .name = "zl30733",
+ .driver_data = (kernel_ulong_t)&zl30733_chip_info,
+ },
+ {
+ .name = "zl30734",
+ .driver_data = (kernel_ulong_t)&zl30734_chip_info,
+ },
+ {
+ .name = "zl30735",
+ .driver_data = (kernel_ulong_t)&zl30735_chip_info,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, zl3073x_spi_id);
+
+static const struct of_device_id zl3073x_spi_of_match[] = {
+ { .compatible = "microchip,zl30731", .data = &zl30731_chip_info },
+ { .compatible = "microchip,zl30732", .data = &zl30732_chip_info },
+ { .compatible = "microchip,zl30733", .data = &zl30733_chip_info },
+ { .compatible = "microchip,zl30734", .data = &zl30734_chip_info },
+ { .compatible = "microchip,zl30735", .data = &zl30735_chip_info },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, zl3073x_spi_of_match);
+
+static struct spi_driver zl3073x_spi_driver = {
+ .driver = {
+ .name = "zl3073x-spi",
+ .of_match_table = zl3073x_spi_of_match,
+ },
+ .probe = zl3073x_spi_probe,
+ .id_table = zl3073x_spi_id,
+};
+module_spi_driver(zl3073x_spi_driver);
+
+MODULE_AUTHOR("Ivan Vecera <ivecera@...hat.com>");
+MODULE_DESCRIPTION("Microchip ZL3073x SPI driver");
+MODULE_IMPORT_NS("ZL3073X");
+MODULE_LICENSE("GPL");
--
2.49.0
Powered by blists - more mailing lists