linux-kernel - [PATCH net-next v2 07/10] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20250813145540.2577789-8-wens@kernel.org>
Date: Wed, 13 Aug 2025 22:55:37 +0800
From: Chen-Yu Tsai <wens@...nel.org>
To: Andrew Lunn <andrew+netdev@...n.ch>,
	"David S. Miller" <davem@...emloft.net>,
	Eric Dumazet <edumazet@...gle.com>,
	Jakub Kicinski <kuba@...nel.org>,
	Paolo Abeni <pabeni@...hat.com>,
	Rob Herring <robh@...nel.org>,
	Krzysztof Kozlowski <krzk+dt@...nel.org>,
	Conor Dooley <conor+dt@...nel.org>,
	Chen-Yu Tsai <wens@...e.org>,
	Jernej Skrabec <jernej@...nel.org>,
	Samuel Holland <samuel@...lland.org>
Cc: netdev@...r.kernel.org,
	devicetree@...r.kernel.org,
	linux-arm-kernel@...ts.infradead.org,
	linux-sunxi@...ts.linux.dev,
	linux-kernel@...r.kernel.org,
	Andre Przywara <andre.przywara@....com>
Subject: [PATCH net-next v2 07/10] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port

From: Chen-Yu Tsai <wens@...e.org>

On the Radxa Cubie A5E board, the second Ethernet controller, aka the
GMAC200, is connected to a second external Maxio MAE0621A PHY. The PHY
uses an external 25MHz crystal, and has the SoC's PJ16 pin connected to
its reset pin.

Enable the second Ethernet port. Also fix up the label for the existing
external PHY connected to the first Ethernet port. An enable delay for the
PHY supply regulator is added to make sure the PHY's internal regulators
are fully powered and the PHY is operational.

Signed-off-by: Chen-Yu Tsai <wens@...e.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
- Add PHY regulator delay
---
 .../dts/allwinner/sun55i-a527-cubie-a5e.dts   | 28 +++++++++++++++++--
 1 file changed, 26 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
index d4cee2222104..e96a419faf21 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
@@ -14,6 +14,7 @@ / {
 
 	aliases {
 		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -76,7 +77,7 @@ &ehci1 {
 
 &gmac0 {
 	phy-mode = "rgmii-id";
-	phy-handle = <&ext_rgmii_phy>;
+	phy-handle = <&ext_rgmii0_phy>;
 	phy-supply = <&reg_cldo3>;
 
 	allwinner,tx-delay-ps = <300>;
@@ -85,13 +86,24 @@ &gmac0 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii1_phy>;
+	phy-supply = <&reg_cldo4>;
+
+	tx-internal-delay-ps = <300>;
+	rx-internal-delay-ps = <400>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
 &mdio0 {
-	ext_rgmii_phy: ethernet-phy@1 {
+	ext_rgmii0_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
@@ -100,6 +112,16 @@ ext_rgmii_phy: ethernet-phy@1 {
 	};
 };
 
+&mdio1 {
+	ext_rgmii1_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 9 16 GPIO_ACTIVE_LOW>; /* PJ16 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
@@ -240,6 +262,8 @@ reg_cldo4: cldo4 {
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-name = "vcc-pj-phy";
+				/* enough time for the PHY to fully power on */
+				regulator-enable-ramp-delay = <150000>;
 			};
 
 			reg_cpusldo: cpusldo {
-- 
2.39.5