Message-ID: <20250818162859.9661-4-john.madieu.xa@bp.renesas.com>
Date: Mon, 18 Aug 2025 18:28:49 +0200
From: John Madieu <john.madieu.xa@...renesas.com>
To: geert+renesas@...der.be,
	magnus.damm@...il.com,
	mturquette@...libre.com,
	sboyd@...nel.org,
	rafael@...nel.org,
	daniel.lezcano@...aro.org,
	rui.zhang@...el.com,
	lukasz.luba@....com,
	robh@...nel.org,
	krzk+dt@...nel.org,
	conor+dt@...nel.org,
	p.zabel@...gutronix.de,
	catalin.marinas@....com,
	will@...nel.org
Cc: john.madieu@...il.com,
	linux-renesas-soc@...r.kernel.org,
	linux-kernel@...r.kernel.org,
	linux-pm@...r.kernel.org,
	devicetree@...r.kernel.org,
	biju.das.jz@...renesas.com,
	linux-arm-kernel@...ts.infradead.org,
	John Madieu <john.madieu.xa@...renesas.com>
Subject: [PATCH v7 3/6] thermal: renesas: rzg3e: Add thermal driver for the Renesas RZ/G3E SoC

The RZ/G3E SoC integrates a Temperature Sensor Unit (TSU) block designed
to monitor the chip's junction temperature. This sensor is connected to
channel 1 of the APB port clock/reset and provides temperature measurements.

It also requires calibration values stored in the system controller registers
for accurate temperature measurement. Add a driver for the Renesas RZ/G3E TSU.

Signed-off-by: John Madieu <john.madieu.xa@...renesas.com>
---

Changes:

v1 -> v2: fixes IRQ names
v2 -> v3: no changes
v3 -> v4: no changes
v5: Removed curly braces arround single-line protected scoped guards
v6: Clarified comments in driver
v7: Refactored driver structure:
  - removes splinlock usage
  - updates polling timeout as per the datasheet
  - uses average mode to be more accurate
  - uses polling (faster than irq mode) for get_temp() while keeping IRQ for hw
  trip-point cross detection.
  - adds both runtime and sleep PM support

 MAINTAINERS                             |   7 +
 drivers/thermal/renesas/Kconfig         |   7 +
 drivers/thermal/renesas/Makefile        |   1 +
 drivers/thermal/renesas/rzg3e_thermal.c | 574 ++++++++++++++++++++++++
 4 files changed, 589 insertions(+)
 create mode 100644 drivers/thermal/renesas/rzg3e_thermal.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 10614ca41ed0..5480412f556d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -21544,6 +21544,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/potentiometer/renesas,x9250.yaml
 F:	drivers/iio/potentiometer/x9250.c
 
+RENESAS RZ/G3E THERMAL SENSOR UNIT DRIVER
+M:	John Madieu <john.madieu.xa@...renesas.com>
+L:	linux-pm@...r.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/thermal/renesas,r9a09g047-tsu.yaml
+F:	drivers/thermal/renesas/rzg3e_thermal.c
+
 RESET CONTROLLER FRAMEWORK
 M:	Philipp Zabel <p.zabel@...gutronix.de>
 S:	Maintained
diff --git a/drivers/thermal/renesas/Kconfig b/drivers/thermal/renesas/Kconfig
index dcf5fc5ae08e..10cf90fc4bfa 100644
--- a/drivers/thermal/renesas/Kconfig
+++ b/drivers/thermal/renesas/Kconfig
@@ -26,3 +26,10 @@ config RZG2L_THERMAL
 	help
 	  Enable this to plug the RZ/G2L thermal sensor driver into the Linux
 	  thermal framework.
+
+config RZG3E_THERMAL
+	tristate "Renesas RZ/G3E thermal driver"
+	depends on ARCH_RENESAS || COMPILE_TEST
+	help
+	  Enable this to plug the RZ/G3E thermal sensor driver into the Linux
+	  thermal framework.
diff --git a/drivers/thermal/renesas/Makefile b/drivers/thermal/renesas/Makefile
index bf9cb3cb94d6..5a3eba0dedd0 100644
--- a/drivers/thermal/renesas/Makefile
+++ b/drivers/thermal/renesas/Makefile
@@ -3,3 +3,4 @@
 obj-$(CONFIG_RCAR_GEN3_THERMAL)	+= rcar_gen3_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o
 obj-$(CONFIG_RZG2L_THERMAL)	+= rzg2l_thermal.o
+obj-$(CONFIG_RZG3E_THERMAL)	+= rzg3e_thermal.o
diff --git a/drivers/thermal/renesas/rzg3e_thermal.c b/drivers/thermal/renesas/rzg3e_thermal.c
new file mode 100644
index 000000000000..c90791f82f33
--- /dev/null
+++ b/drivers/thermal/renesas/rzg3e_thermal.c
@@ -0,0 +1,574 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Renesas RZ/G3E TSU Temperature Sensor Unit
+ *
+ * Copyright (C) 2025 Renesas Electronics Corporation
+ */
+#include <linux/clk.h>
+#include <linux/cleanup.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/thermal.h>
+#include <linux/units.h>
+
+#include "../thermal_hwmon.h"
+
+/* TSU Register offsets and bits */
+#define TSU_SSUSR		0x00
+#define TSU_SSUSR_EN_TS		BIT(0)
+#define TSU_SSUSR_ADC_PD_TS	BIT(1)
+#define TSU_SSUSR_SOC_TS_EN	BIT(2)
+
+#define TSU_STRGR		0x04
+#define TSU_STRGR_ADST		BIT(0)
+
+#define TSU_SOSR1		0x08
+#define TSU_SOSR1_ADCT_8	0x03
+#define TSU_SOSR1_ADCS		BIT(3)
+#define TSU_SOSR1_OUTSEL	BIT(9)
+
+#define TSU_SCRR		0x10
+#define TSU_SCRR_OUT12BIT_TS	GENMASK(11, 0)
+
+#define TSU_SSR			0x14
+#define TSU_SSR_CONV		BIT(0)
+
+#define TSU_CMSR		0x18
+#define TSU_CMSR_CMPEN		BIT(0)
+
+#define TSU_LLSR		0x1C
+#define TSU_ULSR		0x20
+
+#define TSU_SISR		0x30
+#define TSU_SISR_ADF		BIT(0)
+#define TSU_SISR_CMPF		BIT(1)
+
+#define TSU_SIER		0x34
+#define TSU_SIER_CMPIE		BIT(1)
+
+#define TSU_SICR		0x38
+#define TSU_SICR_ADCLR		BIT(0)
+#define TSU_SICR_CMPCLR	BIT(1)
+
+/* Temperature calculation constants from datasheet */
+#define TSU_TEMP_D		(-41)
+#define TSU_TEMP_E		126
+#define TSU_CODE_MAX		0xFFF
+
+/* Timing specifications from datasheet */
+#define TSU_POWERUP_TIME_US	120	/* 120T at 1MHz sensor clock per datasheet */
+#define TSU_CONV_TIME_US	50	/* Per sample conversion time */
+#define TSU_POLL_DELAY_US	10	/* Polling interval */
+#define TSU_MIN_CLOCK_RATE	24000000  /* TSU_PCLK minimum 24MHz */
+
+/* Temperature limits */
+#define TSU_TEMP_MIN_MC	(-40000)
+#define TSU_TEMP_MAX_MC	125000
+
+/**
+ * struct rzg3e_thermal_priv - RZ/G3E TSU private data
+ * @base: TSU register base
+ * @dev: device pointer
+ * @syscon: regmap for calibration values
+ * @zone: thermal zone device
+ * @rstc: reset control
+ * @trmval0: calibration value 0 (b)
+ * @trmval1: calibration value 1 (c)
+ * @trim_offset: offset for trim registers in syscon
+ * @lock: protects hardware access during conversions
+ */
+struct rzg3e_thermal_priv {
+	void __iomem *base;
+	struct device *dev;
+	struct regmap *syscon;
+	struct thermal_zone_device *zone;
+	struct reset_control *rstc;
+	u16 trmval0;
+	u16 trmval1;
+	u32 trim_offset;
+	struct mutex lock;
+};
+
+static inline u32 rzg3e_thermal_read(struct rzg3e_thermal_priv *priv, u32 reg)
+{
+	return readl(priv->base + reg);
+}
+
+static inline void rzg3e_thermal_write(struct rzg3e_thermal_priv *priv,
+				       u32 reg, u32 val)
+{
+	writel(val, priv->base + reg);
+}
+
+static int rzg3e_thermal_power_on(struct rzg3e_thermal_priv *priv)
+{
+	u32 val;
+	int ret;
+
+	/* Clear any pending interrupts */
+	rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_ADCLR | TSU_SICR_CMPCLR);
+
+	/* Disable all interrupts during setup */
+	rzg3e_thermal_write(priv, TSU_SIER, 0);
+
+	/*
+	 * Power-on sequence per datasheet 7.11.9.1:
+	 * SOC_TS_EN must be set at same time or before EN_TS and ADC_PD_TS
+	 */
+	val = TSU_SSUSR_SOC_TS_EN | TSU_SSUSR_EN_TS;
+	rzg3e_thermal_write(priv, TSU_SSUSR, val);
+
+	/* Wait for sensor stabilization per datasheet 7.11.7.1 */
+	usleep_range(TSU_POWERUP_TIME_US, TSU_POWERUP_TIME_US + 10);
+
+	/* Configure for average mode with 8 samples */
+	val = TSU_SOSR1_OUTSEL | TSU_SOSR1_ADCT_8;
+	rzg3e_thermal_write(priv, TSU_SOSR1, val);
+
+	/* Ensure we're in single scan mode (default) */
+	val = rzg3e_thermal_read(priv, TSU_SOSR1);
+	if (val & TSU_SOSR1_ADCS) {
+		dev_err(priv->dev, "Invalid scan mode setting\n");
+		return -EINVAL;
+	}
+
+	/* Wait for any ongoing conversion to complete */
+	ret = readl_poll_timeout(priv->base + TSU_SSR, val,
+				 !(val & TSU_SSR_CONV),
+				 TSU_POLL_DELAY_US,
+				 USEC_PER_MSEC);
+	if (ret) {
+		dev_err(priv->dev, "Timeout waiting for conversion\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void rzg3e_thermal_power_off(struct rzg3e_thermal_priv *priv)
+{
+	/* Disable all interrupts */
+	rzg3e_thermal_write(priv, TSU_SIER, 0);
+
+	/* Clear pending interrupts */
+	rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_ADCLR | TSU_SICR_CMPCLR);
+
+	/* Power down sequence per datasheet */
+	rzg3e_thermal_write(priv, TSU_SSUSR, TSU_SSUSR_ADC_PD_TS);
+}
+
+/*
+ * Convert 12-bit sensor code to temperature in millicelsius
+ * Formula from datasheet 7.11.7.8:
+ * T(°C) = ((e - d) / (c - b)) * (a - b) + d
+ * where: a = sensor code, b = trmval0, c = trmval1, d = -41, e = 126
+ */
+static int rzg3e_thermal_code_to_temp(struct rzg3e_thermal_priv *priv, u16 code)
+{
+	s64 numerator, denominator;
+	int temp_c;
+
+	numerator = (TSU_TEMP_E - TSU_TEMP_D) * (s64)(code - priv->trmval0);
+	denominator = priv->trmval1 - priv->trmval0;
+
+	temp_c = div64_s64(numerator, denominator) + TSU_TEMP_D;
+
+	return clamp(temp_c * MILLIDEGREE_PER_DEGREE,
+		     TSU_TEMP_MIN_MC, TSU_TEMP_MAX_MC);
+}
+
+/*
+ * Convert temperature in millicelsius to 12-bit sensor code
+ * Formula from datasheet 7.11.7.9 (inverse of above)
+ */
+static u16 rzg3e_thermal_temp_to_code(struct rzg3e_thermal_priv *priv, int temp_mc)
+{
+	int temp_c = temp_mc / MILLIDEGREE_PER_DEGREE;
+	s64 numerator, denominator;
+	s64 code;
+
+	numerator = (temp_c - TSU_TEMP_D) * (priv->trmval1 - priv->trmval0);
+	denominator = TSU_TEMP_E - TSU_TEMP_D;
+
+	code = div64_s64(numerator, denominator) + priv->trmval0;
+
+	return clamp_val(code, 0, TSU_CODE_MAX);
+}
+
+static int rzg3e_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+	struct rzg3e_thermal_priv *priv = thermal_zone_device_priv(tz);
+	u32 status, code;
+	int ret, timeout;
+
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
+		return ret;
+
+	guard(mutex)(&priv->lock);
+
+	/* Clear any previous conversion status */
+	rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_ADCLR);
+
+	/* Start single conversion */
+	rzg3e_thermal_write(priv, TSU_STRGR, TSU_STRGR_ADST);
+
+	/* Wait for conversion completion - 8 samples at ~50us each */
+	timeout = TSU_CONV_TIME_US * 8 * 2;  /* Double for margin */
+	ret = readl_poll_timeout(priv->base + TSU_SISR, status,
+				 status & TSU_SISR_ADF,
+				 TSU_POLL_DELAY_US, timeout);
+	if (ret) {
+		dev_err(priv->dev, "Conversion timeout (status=0x%08x)\n", status);
+		goto out;
+	}
+
+	/* Read the averaged result and clear the complete flag */
+	code = rzg3e_thermal_read(priv, TSU_SCRR) & TSU_SCRR_OUT12BIT_TS;
+	rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_ADCLR);
+
+	/* Convert to temperature */
+	*temp = rzg3e_thermal_code_to_temp(priv, code);
+
+	dev_dbg(priv->dev, "temp=%d mC (%d.%03d°C), code=0x%03x\n",
+		*temp, *temp / 1000, abs(*temp) % 1000, code);
+
+out:
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+	return ret;
+}
+
+static int rzg3e_thermal_set_trips(struct thermal_zone_device *tz,
+				   int low, int high)
+{
+	struct rzg3e_thermal_priv *priv = thermal_zone_device_priv(tz);
+	u16 low_code, high_code;
+	u32 val;
+	int ret;
+
+	/* Hardware requires low < high */
+	if (low >= high)
+		return -EINVAL;
+
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
+		return ret;
+
+	guard(mutex)(&priv->lock);
+
+	/* Convert temperatures to codes */
+	low_code = rzg3e_thermal_temp_to_code(priv, low);
+	high_code = rzg3e_thermal_temp_to_code(priv, high);
+
+	dev_dbg(priv->dev, "set_trips: low=%d high=%d (codes: 0x%03x/0x%03x)\n",
+		low, high, low_code, high_code);
+
+	/* Disable comparison during reconfiguration */
+	rzg3e_thermal_write(priv, TSU_SIER, 0);
+	rzg3e_thermal_write(priv, TSU_CMSR, 0);
+
+	/* Clear any pending comparison interrupts */
+	rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_CMPCLR);
+
+	/* Set trip points */
+	rzg3e_thermal_write(priv, TSU_LLSR, low_code);
+	rzg3e_thermal_write(priv, TSU_ULSR, high_code);
+
+	/*
+	 * Ensure OUTSEL is set for comparison per datasheet 7.11.7.4
+	 * Comparison uses averaged data
+	 */
+	val = rzg3e_thermal_read(priv, TSU_SOSR1);
+	val |= TSU_SOSR1_OUTSEL;
+	rzg3e_thermal_write(priv, TSU_SOSR1, val);
+
+	/* Enable comparison with "out of range" mode (CMPCOND=0) */
+	rzg3e_thermal_write(priv, TSU_CMSR, TSU_CMSR_CMPEN);
+
+	/* Unmask compare IRQ and start a conversion to evaluate window */
+	rzg3e_thermal_write(priv, TSU_SIER, TSU_SIER_CMPIE);
+	rzg3e_thermal_write(priv, TSU_STRGR, TSU_STRGR_ADST);
+
+	pm_runtime_mark_last_busy(priv->dev);
+	pm_runtime_put_autosuspend(priv->dev);
+
+	return 0;
+}
+
+static irqreturn_t rzg3e_thermal_irq_thread(int irq, void *data)
+{
+	struct rzg3e_thermal_priv *priv = data;
+
+	dev_dbg(priv->dev, "Temperature threshold crossed\n");
+
+	/* Notify thermal framework to re-evaluate trip points */
+	thermal_zone_device_update(priv->zone, THERMAL_TRIP_VIOLATED);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t rzg3e_thermal_irq(int irq, void *data)
+{
+	struct rzg3e_thermal_priv *priv = data;
+	u32 status;
+
+	status = rzg3e_thermal_read(priv, TSU_SISR);
+
+	/* Check if comparison interrupt occurred */
+	if (status & TSU_SISR_CMPF) {
+		/* Clear irq flag and disable interrupt until reconfigured */
+		rzg3e_thermal_write(priv, TSU_SICR, TSU_SICR_CMPCLR);
+		rzg3e_thermal_write(priv, TSU_SIER, 0);
+
+		return IRQ_WAKE_THREAD;
+	}
+
+	return IRQ_NONE;
+}
+
+static const struct thermal_zone_device_ops rzg3e_tz_ops = {
+	.get_temp = rzg3e_thermal_get_temp,
+	.set_trips = rzg3e_thermal_set_trips,
+};
+
+static int rzg3e_thermal_get_calibration(struct rzg3e_thermal_priv *priv)
+{
+	u32 val;
+	int ret;
+
+	/* Read calibration values from syscon */
+	ret = regmap_read(priv->syscon, priv->trim_offset, &val);
+	if (ret)
+		return ret;
+	priv->trmval0 = val & GENMASK(11, 0);
+
+	ret = regmap_read(priv->syscon, priv->trim_offset + 4, &val);
+	if (ret)
+		return ret;
+	priv->trmval1 = val & GENMASK(11, 0);
+
+	/* Validate calibration data */
+	if (!priv->trmval0 || !priv->trmval1 ||
+	    priv->trmval0 == priv->trmval1 ||
+	    priv->trmval0 == 0xFFF || priv->trmval1 == 0xFFF) {
+		dev_err(priv->dev, "Invalid calibration: b=0x%03x, c=0x%03x\n",
+			priv->trmval0, priv->trmval1);
+		return -EINVAL;
+	}
+
+	dev_dbg(priv->dev, "Calibration: b=0x%03x (%u), c=0x%03x (%u)\n",
+		priv->trmval0, priv->trmval0, priv->trmval1, priv->trmval1);
+
+	return 0;
+}
+
+static int rzg3e_thermal_parse_dt(struct rzg3e_thermal_priv *priv)
+{
+	struct device_node *np = priv->dev->of_node;
+	struct of_phandle_args args;
+	int ret;
+
+	ret = of_parse_phandle_with_args(np, "renesas,tsu-trim",
+					 "#address-cells", 0, &args);
+	if (ret)
+		return dev_err_probe(priv->dev, ret,
+				     "Failed to parse renesas,tsu-trim\n");
+
+	if (args.args_count < 1) {
+		dev_err(priv->dev, "Invalid renesas,tsu-trim property\n");
+		of_node_put(args.np);
+		return -EINVAL;
+	}
+
+	priv->trim_offset = args.args[0];
+
+	priv->syscon = syscon_node_to_regmap(args.np);
+	of_node_put(args.np);
+
+	if (IS_ERR(priv->syscon))
+		return dev_err_probe(priv->dev, PTR_ERR(priv->syscon),
+				     "Failed to get syscon regmap\n");
+
+	return 0;
+}
+
+static int rzg3e_thermal_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rzg3e_thermal_priv *priv;
+	struct clk *clk;
+	int irq, ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	mutex_init(&priv->lock);
+	platform_set_drvdata(pdev, priv);
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	/* Parse device tree for trim register info */
+	ret = rzg3e_thermal_parse_dt(priv);
+	if (ret)
+		return ret;
+
+	/* Get clock to verify frequency - clock is managed by power domain */
+	clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(clk))
+		return dev_err_probe(dev, PTR_ERR(clk),
+				     "Failed to get clock\n");
+
+	if (clk_get_rate(clk) < TSU_MIN_CLOCK_RATE)
+		return dev_err_probe(dev, -EINVAL,
+				     "Clock rate %lu Hz too low (min %u Hz)\n",
+				     clk_get_rate(clk), TSU_MIN_CLOCK_RATE);
+
+	priv->rstc = devm_reset_control_get_exclusive_deasserted(dev, NULL);
+	if (IS_ERR(priv->rstc))
+		return dev_err_probe(dev, PTR_ERR(priv->rstc),
+				     "Failed to get/deassert reset control\n");
+
+	/* Get calibration data */
+	ret = rzg3e_thermal_get_calibration(priv);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to get valid calibration data\n");
+
+	/* Get comparison interrupt */
+	irq = platform_get_irq_byname(pdev, "adcmpi");
+	if (irq < 0)
+		return irq;
+
+	/* Enable runtime PM */
+	pm_runtime_set_autosuspend_delay(dev, 1000);
+	pm_runtime_use_autosuspend(dev);
+	devm_pm_runtime_enable(dev);
+
+	/* Initial hardware setup */
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Runtime resume failed\n");
+
+	/* Register thermal zone - this will trigger DT parsing */
+	priv->zone = devm_thermal_of_zone_register(dev, 0, priv, &rzg3e_tz_ops);
+	if (IS_ERR(priv->zone)) {
+		ret = PTR_ERR(priv->zone);
+		dev_err(dev, "Failed to register thermal zone: %d\n", ret);
+		goto err_pm_put;
+	}
+
+	/* Request threaded IRQ for comparison interrupt */
+	ret = devm_request_threaded_irq(dev, irq, rzg3e_thermal_irq,
+					rzg3e_thermal_irq_thread,
+					IRQF_ONESHOT, "rzg3e_thermal", priv);
+	if (ret) {
+		dev_err(dev, "Failed to request IRQ: %d\n", ret);
+		goto err_pm_put;
+	}
+
+	/* Add hwmon sysfs interface */
+	ret = devm_thermal_add_hwmon_sysfs(dev, priv->zone);
+	if (ret)
+		dev_warn(dev, "Failed to add hwmon sysfs attributes\n");
+
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+
+	dev_info(dev, "RZ/G3E thermal sensor registered\n");
+
+	return 0;
+
+err_pm_put:
+	pm_runtime_put_sync(dev);
+	return ret;
+}
+
+static int rzg3e_thermal_runtime_suspend(struct device *dev)
+{
+	struct rzg3e_thermal_priv *priv = dev_get_drvdata(dev);
+
+	rzg3e_thermal_power_off(priv);
+	return 0;
+}
+
+static int rzg3e_thermal_runtime_resume(struct device *dev)
+{
+	struct rzg3e_thermal_priv *priv = dev_get_drvdata(dev);
+
+	return rzg3e_thermal_power_on(priv);
+}
+
+static int rzg3e_thermal_suspend(struct device *dev)
+{
+	struct rzg3e_thermal_priv *priv = dev_get_drvdata(dev);
+
+	/* If device is active, power it off */
+	if (pm_runtime_active(dev))
+		rzg3e_thermal_power_off(priv);
+
+	/* Assert reset to ensure clean state after resume */
+	reset_control_assert(priv->rstc);
+
+	return 0;
+}
+
+static int rzg3e_thermal_resume(struct device *dev)
+{
+	struct rzg3e_thermal_priv *priv = dev_get_drvdata(dev);
+	int ret;
+
+	/* Deassert reset */
+	ret = reset_control_deassert(priv->rstc);
+	if (ret) {
+		dev_err(dev, "Failed to deassert reset: %d\n", ret);
+		return ret;
+	}
+
+	/* If device was active before suspend, power it back on */
+	if (pm_runtime_active(dev))
+		return rzg3e_thermal_power_on(priv);
+
+	return 0;
+}
+
+static const struct dev_pm_ops rzg3e_thermal_pm_ops = {
+	RUNTIME_PM_OPS(rzg3e_thermal_runtime_suspend,
+		       rzg3e_thermal_runtime_resume, NULL)
+	SYSTEM_SLEEP_PM_OPS(rzg3e_thermal_suspend, rzg3e_thermal_resume)
+};
+
+static const struct of_device_id rzg3e_thermal_dt_ids[] = {
+	{ .compatible = "renesas,r9a09g047-tsu" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rzg3e_thermal_dt_ids);
+
+static struct platform_driver rzg3e_thermal_driver = {
+	.driver = {
+		.name = "rzg3e_thermal",
+		.of_match_table = rzg3e_thermal_dt_ids,
+		.pm = pm_ptr(&rzg3e_thermal_pm_ops),
+	},
+	.probe = rzg3e_thermal_probe,
+};
+module_platform_driver(rzg3e_thermal_driver);
+
+MODULE_DESCRIPTION("Renesas RZ/G3E TSU Thermal Sensor Driver");
+MODULE_AUTHOR("John Madieu <john.madieu.xa@...renesas.com>");
+MODULE_LICENSE("GPL");
-- 
2.25.1

Powered by blists - more mailing lists