| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20250826181506.3698370-3-umang.chheda@oss.qualcomm.com>
Date: Tue, 26 Aug 2025 23:45:06 +0530
From: Umang Chheda <umang.chheda@....qualcomm.com>
To: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Richard Cochran <richardcochran@...il.com>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Umang Chheda <umang.chheda@....qualcomm.com>,
Rakesh Kota <rakesh.kota@....qualcomm.com>,
Nirmesh Kumar Singh <quic_nkumarsi@...cinc.com>,
Viken Dadhaniya <viken.dadhaniya@....qualcomm.com>,
Mohd Ayaan Anwar <quic_mohdayaa@...cinc.com>,
Arun Khannna <quic_arkhanna@...cinc.com>,
Monish Chunara <quic_mchunara@...cinc.com>,
Vikash Garodia <quic_vgarodia@...cinc.com>,
Swati Agarwal <swati.agarwal@....qualcomm.com>
Subject: [PATCH v3 2/2] arm64: dts: qcom: Add Monaco EVK initial board support
Add initial device tree support for Monaco EVK board, based on
Qualcomm's QCS8300 SoC.
Monaco EVK is single board supporting these peripherals:
- Storage: 1 × 128 GB UFS, micro-SD card, EEPROMs for MACs,
and eMMC.
- Audio/Video, Camera & Display ports.
- Connectivity: RJ45 2.5GbE, WLAN/Bluetooth, CAN/CAN-FD.
- PCIe ports.
- USB & UART ports.
On top of Monaco EVK board additional mezzanine boards can be
stacked in future.
Add support for the following components :
- GPI (Generic Peripheral Interface) and QUPv3-0/1
controllers to facilitate DMA and peripheral communication.
- TCA9534 I/O expander via I2C to provide 8 additional GPIO
lines for extended I/O functionality.
- USB1 controller in device mode to support USB peripheral
operations.
- Remoteproc subsystems for supported DSPs such as Audio DSP,
Compute DSP and Generic DSP, along with their corresponding
firmware.
- Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
and other consumers.
- QCA8081 2.5G Ethernet PHY on port-0 and expose the
Ethernet MAC address via nvmem for network configuration.
It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
- Support for the Iris video decoder, including the required
firmware, to enable video decoding capabilities.
Co-developed-by: Rakesh Kota <rakesh.kota@....qualcomm.com>
Signed-off-by: Rakesh Kota <rakesh.kota@....qualcomm.com>
Co-developed-by: Nirmesh Kumar Singh <quic_nkumarsi@...cinc.com>
Signed-off-by: Nirmesh Kumar Singh <quic_nkumarsi@...cinc.com>
Co-developed-by: Viken Dadhaniya <viken.dadhaniya@....qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@....qualcomm.com>
Co-developed-by: Mohd Ayaan Anwar <quic_mohdayaa@...cinc.com>
Signed-off-by: Mohd Ayaan Anwar <quic_mohdayaa@...cinc.com>
Co-developed-by: Arun Khannna <quic_arkhanna@...cinc.com>
Signed-off-by: Arun Khannna <quic_arkhanna@...cinc.com>
Co-developed-by: Monish Chunara <quic_mchunara@...cinc.com>
Signed-off-by: Monish Chunara <quic_mchunara@...cinc.com>
Co-developed-by: Vikash Garodia <quic_vgarodia@...cinc.com>
Signed-off-by: Vikash Garodia <quic_vgarodia@...cinc.com>
Co-developed-by: Swati Agarwal <swati.agarwal@....qualcomm.com>
Signed-off-by: Swati Agarwal <swati.agarwal@....qualcomm.com>
Signed-off-by: Umang Chheda <umang.chheda@....qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/monaco-evk.dts | 463 ++++++++++++++++++++++++
2 files changed, 464 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/monaco-evk.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 94a84770b080..057a81ea04ed 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -30,6 +30,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp449.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp453.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp454.dtb
dtb-$(CONFIG_ARCH_QCOM) += lemans-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM) += monaco-evk.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8216-samsung-fortuna3g.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
diff --git a/arch/arm64/boot/dts/qcom/monaco-evk.dts b/arch/arm64/boot/dts/qcom/monaco-evk.dts
new file mode 100644
index 000000000000..8d58e62f6c87
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/monaco-evk.dts
@@ -0,0 +1,463 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "qcs8300.dtsi"
+#include "qcs8300-pmics.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Monaco EVK";
+ compatible = "qcom,monaco-evk", "qcom,qcs8300";
+
+ aliases {
+ ethernet0 = ðernet0;
+ i2c1 = &i2c1;
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4a: ldo4 {
+ regulator-name = "vreg_l4a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a: ldo6 {
+ regulator-name = "vreg_l6a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a: ldo9 {
+ regulator-name = "vreg_l9a";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_s5c: smps5 {
+ regulator-name = "vreg_s5c";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <512000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+ðernet0 {
+ phy-mode = "2500base-x";
+ phy-handle = <&hsgmii_phy0>;
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,ps-speed = <1000>;
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ eeprom0: eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-addr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+ };
+};
+
+&i2c15 {
+ pinctrl-0 = <&qup_i2c15_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ expander0: pca953x@38 {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x38>;
+ };
+
+ expander1: pca953x@39 {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x39>;
+ };
+
+ expander2: pca953x@3a {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3a>;
+ };
+
+ expander3: pca953x@3b {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3b>;
+ };
+
+ expander4: pca953x@3c {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3c>;
+ };
+
+ expander5: pca953x@3d {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3d>;
+ };
+
+ expander6: pca953x@3e {
+ compatible = "ti,tca9538";
+ #gpio-cells = <2>;
+ gpio-controller;
+ reg = <0x3e>;
+ };
+};
+
+&iris {
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs8300/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs8300/cdsp0.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_gpdsp {
+ firmware-name = "qcom/qcs8300/gpdsp0.mbn";
+
+ status = "okay";
+};
+
+&serdes0 {
+ phy-supply = <&vreg_l4a>;
+
+ status = "okay";
+};
+
+&tlmm {
+ ethernet0_default: ethernet0-default-state {
+ ethernet0_mdc: ethernet0-mdc-pins {
+ pins = "gpio5";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0_mdio: ethernet0-mdio-pins {
+ pins = "gpio6";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ qup_i2c1_default: qup-i2c1-state {
+ pins = "gpio19", "gpio20";
+ function = "qup0_se1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c15_default: qup-i2c15-state {
+ pins = "gpio91", "gpio92";
+ function = "qup1_se7";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+&uart7 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l8a>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l4c>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l4a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l7a>;
+ vdda18-supply = <&vreg_l7c>;
+ vdda33-supply = <&vreg_l9a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy {
+ vdda-phy-supply = <&vreg_l7a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
--
2.34.1
Powered by blists - more mailing lists