[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <036589cf-3e78-42ea-9876-2a01acdbb598@freeshell.de>
Date: Sun, 31 Aug 2025 15:46:26 -0700
From: E Shattow <e@...eshell.de>
To: Hal Feng <hal.feng@...ux.starfivetech.com>,
Emil Renner Berthing <kernel@...il.dk>, Conor Dooley <conor@...nel.org>,
Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
Paul Walmsley <paul.walmsley@...ive.com>, Palmer Dabbelt
<palmer@...belt.com>, Albert Ou <aou@...s.berkeley.edu>,
Alexandre Ghiti <alex@...ti.fr>
Cc: devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-riscv@...ts.infradead.org
Subject: Re: [PATCH v1 4/4] riscv: dts: starfive: add Milk-V Mars CM Lite
system-on-module
On 8/20/25 19:40, Hal Feng wrote:
> On 7/24/2025 5:48 PM, E Shattow wrote:
>> Milk-V Mars CM Lite is a System-on-Module based on the Milk-V Mars CM
>> without the onboard eMMC storage component populated and configured
>> instead for SD3.0 Card Slot on that interface via 100-pin connector.
>>
>> Link to Milk-V Mars CM Lite schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
>> Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
>> Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
>>
>> Add the devicetree file to make use of StarFive JH7110 common supported
>> features PMIC, EEPROM, UART, I2C, GPIO, PCIe, QSPI Flash, PWM, and
>> Ethernet. Also configure the eMMC interface mmc0 for SD Card use and
>> configure the common SD Card interface mmc1 for onboard SDIO BT+WiFi.
>>
>> Signed-off-by: E Shattow <e@...eshell.de>
>> ---
>> arch/riscv/boot/dts/starfive/Makefile | 1 +
>> .../dts/starfive/jh7110-milkv-marscm-lite.dts | 176 ++++++++++++++++++
>> 2 files changed, 177 insertions(+)
>> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
>>
>> diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
>> index 79742617ddab..62b659f89ba7 100644
>> --- a/arch/riscv/boot/dts/starfive/Makefile
>> +++ b/arch/riscv/boot/dts/starfive/Makefile
>> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
>> +dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
>> dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
>> new file mode 100644
>> index 000000000000..e110146f0b76
>> --- /dev/null
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
>> @@ -0,0 +1,176 @@
>> +// SPDX-License-Identifier: GPL-2.0 OR MIT
>> +/*
>> + * Copyright (C) 2025 E Shattow <e@...eshell.de>
>> + */
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/pinctrl/starfive,jh7110-pinctrl.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include "jh7110-common.dtsi"
>
> You can just include "jh7110-milkv-marscm-emmc.dts" instead of "jh7110-common.dtsi".
> And then adding mmc0 changes will be enough.
>
> Best regards,
> Hal
>
> ...
>
>> +&mmc0 {
>> + bus-width = <4>;
>> + cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
>> +};
>> +
>> +&mmc0_pins {
>> + pwren-pins {
>> + pinmux = <GPIOMUX(22, GPOUT_HIGH,
>> + GPOEN_ENABLE,
>> + GPI_NONE)>;
>> + };
>> +};
>> +
> ...
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@...ts.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv
Okay. I will refactor the series to create and use
"jh7110-milkv-marscm.dtsi" common board include.
-E
Powered by blists - more mailing lists