| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250912141134.2799078-3-quic_vikramsa@quicinc.com>
Date: Fri, 12 Sep 2025 19:41:33 +0530
From: Vikram Sharma <quic_vikramsa@...cinc.com>
To: <vladimir.zapolskiy@...aro.org>, <bryan.odonoghue@...aro.org>,
<mchehab@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
<conor+dt@...nel.org>, <andersson@...nel.org>,
<konradybcio@...nel.org>, <hverkuil-cisco@...all.nl>,
<cros-qcom-dts-watchers@...omium.org>, <catalin.marinas@....com>,
<will@...nel.org>
CC: <linux-arm-kernel@...ts.infradead.org>, <quic_vikramsa@...cinc.com>,
<quic_nihalkum@...cinc.com>, <quic_svankada@...cinc.com>,
<linux-media@...r.kernel.org>, <linux-arm-msm@...r.kernel.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Ravi Shankar
<quic_rshankar@...cinc.com>,
Vishal Verma <quic_vishverm@...cinc.com>
Subject: [PATCH v2 2/3] arm64: dts: qcom: qcs8300: Add CCI definitions
From: Nihal Kumar Gupta <quic_nihalkum@...cinc.com>
Add support for three Camera Control Interface (CCI) controllers
on the Qualcomm QCS8300 SoC. Configure clocks, power domains,
pinctrl states and two I2C buses (i2c0, i2c1) with 1 MHz frequency.
Nodes are added in a disabled state by default.
Co-developed-by: Ravi Shankar <quic_rshankar@...cinc.com>
Signed-off-by: Ravi Shankar <quic_rshankar@...cinc.com>
Co-developed-by: Vishal Verma <quic_vishverm@...cinc.com>
Signed-off-by: Vishal Verma <quic_vishverm@...cinc.com>
Co-developed-by: Suresh Vankadara <quic_svankada@...cinc.com>
Signed-off-by: Suresh Vankadara <quic_svankada@...cinc.com>
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum@...cinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@...cinc.com>
---
arch/arm64/boot/dts/qcom/qcs8300.dtsi | 309 ++++++++++++++++++++++++++
1 file changed, 309 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
index a248e269d72d..a69719e291ea 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
@@ -4681,6 +4681,123 @@ videocc: clock-controller@...0000 {
#power-domain-cells = <1>;
};
+ cci0: cci@...3000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac13000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_0_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci0_i2c0_default &cci0_i2c1_default>;
+ pinctrl-1 = <&cci0_i2c0_sleep &cci0_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci0_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci0_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci1: cci@...4000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac14000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_1_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci1_i2c0_default &cci1_i2c1_default>;
+ pinctrl-1 = <&cci1_i2c0_sleep &cci1_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci1_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci1_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci2: cci@...5000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac15000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 651 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_2_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci2_i2c0_default &cci2_i2c1_default>;
+ pinctrl-1 = <&cci2_i2c0_sleep &cci2_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci2_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci2_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
camss: isp@...8000 {
compatible = "qcom,qcs8300-camss";
@@ -4975,6 +5092,198 @@ tlmm: pinctrl@...0000 {
#interrupt-cells = <2>;
wakeup-parent = <&pdc>;
+ cci0_i2c0_default: cci0-0-default-state {
+ sda-pins {
+ pins = "gpio57";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio58";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci0_i2c0_sleep: cci0-0-sleep-state {
+ sda-pins {
+ pins = "gpio57";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio58";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci0_i2c1_default: cci0-1-default-state {
+ sda-pins {
+ pins = "gpio29";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio30";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci0_i2c1_sleep: cci0-1-sleep-state {
+ sda-pins {
+ pins = "gpio29";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio30";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_i2c0_default: cci1-0-default-state {
+ sda-pins {
+ pins = "gpio59";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio60";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci1_i2c0_sleep: cci1-0-sleep-state {
+ sda-pins {
+ pins = "gpio59";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio60";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_i2c1_default: cci1-1-default-state {
+ sda-pins {
+ pins = "gpio31";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio32";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci1_i2c1_sleep: cci1-1-sleep-state {
+ sda-pins {
+ pins = "gpio31";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio32";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_i2c0_default: cci2-0-default-state {
+ sda-pins {
+ pins = "gpio61";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio62";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci2_i2c0_sleep: cci2-0-sleep-state {
+ sda-pins {
+ pins = "gpio61";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio62";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_i2c1_default: cci2-1-default-state {
+ sda-pins {
+ pins = "gpio54";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio55";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci2_i2c1_sleep: cci2-1-sleep-state {
+ sda-pins {
+ pins = "gpio54";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio55";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
hs0_mi2s_active: hs0-mi2s-active-state {
pins = "gpio106", "gpio107", "gpio108", "gpio109";
function = "hs0_mi2s";
--
2.25.1
Powered by blists - more mailing lists