[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20250912183003.1115957-1-Frank.Li@nxp.com>
Date: Fri, 12 Sep 2025 14:30:02 -0400
From: Frank Li <Frank.Li@....com>
To: "Lad, Prabhakar" <prabhakar.csengg@...il.com>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Jacopo Mondi <jacopo.mondi@...asonboard.com>,
Nicholas Roth <nicholas@...hemail.net>,
linux-media@...r.kernel.org (open list:OV2659 OMNIVISION SENSOR DRIVER),
devicetree@...r.kernel.org (open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS),
linux-kernel@...r.kernel.org (open list)
Cc: imx@...ts.linux.dev
Subject: [PATCH 1/1] media: dt-bindings: move ovti,ov2659.txt into ovti,ov8858.yaml
The properties in ovti,ov2659.txt are the same as ovti,ov8858. So move it
to this yaml file.
Signed-off-by: Frank Li <Frank.Li@....com>
---
.../bindings/media/i2c/ovti,ov2659.txt | 47 -------------------
.../bindings/media/i2c/ovti,ov8858.yaml | 4 +-
2 files changed, 3 insertions(+), 48 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt
deleted file mode 100644
index 92989a619f292..0000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ovti,ov2659.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-* OV2659 1/5-Inch 2Mp SOC Camera
-
-The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of
-1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports
-multiple resolutions output, such as UXGA, SVGA, 720p. It also can support
-YUV422, RGB565/555 or raw RGB output formats.
-
-Required Properties:
-- compatible: Must be "ovti,ov2659"
-- reg: I2C slave address
-- clocks: reference to the xvclk input clock.
-- clock-names: should be "xvclk".
-- link-frequencies: target pixel clock frequency.
-
-Optional Properties:
-- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
- Active high with internal pull down resistor.
-- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
- Active low with internal pull up resistor.
-
-For further reading on port node refer to
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-
- i2c0@...2000 {
- ...
- ...
- ov2659@30 {
- compatible = "ovti,ov2659";
- reg = <0x30>;
-
- clocks = <&clk_ov2659 0>;
- clock-names = "xvclk";
-
- powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
-
- port {
- ov2659_0: endpoint {
- remote-endpoint = <&vpfe_ep>;
- link-frequencies = /bits/ 64 <70000000>;
- };
- };
- };
- ...
- };
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml
index 491f2931e6bcd..d7059dbee7fca 100644
--- a/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8858.yaml
@@ -19,7 +19,9 @@ $ref: /schemas/media/video-interface-devices.yaml#
properties:
compatible:
- const: ovti,ov8858
+ enum:
+ - ovti,ov2659
+ - ovti,ov8858
reg:
maxItems: 1
--
2.34.1
Powered by blists - more mailing lists