| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <aMSHsoLHGUBoWX8e@lizhi-Precision-Tower-5810>
Date: Fri, 12 Sep 2025 16:50:58 -0400
From: Frank Li <Frank.li@....com>
To: Vincent Guittot <vincent.guittot@...aro.org>
Cc: chester62515@...il.com, mbrugger@...e.com,
ghennadi.procopciuc@....nxp.com, s32@....com, lpieralisi@...nel.org,
kwilczynski@...nel.org, mani@...nel.org, robh@...nel.org,
krzk+dt@...nel.org, conor+dt@...nel.org, Ionut.Vicovan@....com,
larisa.grigore@....com, Ghennadi.Procopciuc@....com,
ciprianmarian.costea@....com, bogdan.hamciuc@....com,
linux-arm-kernel@...ts.infradead.org, linux-pci@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 1/4] dt-bindings: pcie: Add the NXP PCIe controller
On Fri, Sep 12, 2025 at 04:14:33PM +0200, Vincent Guittot wrote:
> Describe the PCIe controller available on the S32G platforms.
can you cc imx@...ts.linux.dev next time? suppose most part is similar with
imx and layerscape chips.
>
> Co-developed-by: Ionut Vicovan <Ionut.Vicovan@....com>
> Signed-off-by: Ionut Vicovan <Ionut.Vicovan@....com>
> Co-developed-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@....com>
> Signed-off-by: Bogdan-Gabriel Roman <bogdan-gabriel.roman@....com>
> Co-developed-by: Larisa Grigore <larisa.grigore@....com>
> Signed-off-by: Larisa Grigore <larisa.grigore@....com>
> Co-developed-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@....com>
> Signed-off-by: Ghennadi Procopciuc <Ghennadi.Procopciuc@....com>
> Co-developed-by: Ciprian Marian Costea <ciprianmarian.costea@....com>
> Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@....com>
> Co-developed-by: Bogdan Hamciuc <bogdan.hamciuc@....com>
> Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@....com>
> Signed-off-by: Vincent Guittot <vincent.guittot@...aro.org>
> ---
> .../devicetree/bindings/pci/nxp,s32-pcie.yaml | 169 ++++++++++++++++++
> 1 file changed, 169 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/nxp,s32-pcie.yaml
>
> diff --git a/Documentation/devicetree/bindings/pci/nxp,s32-pcie.yaml b/Documentation/devicetree/bindings/pci/nxp,s32-pcie.yaml
> new file mode 100644
> index 000000000000..287596d7162d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/nxp,s32-pcie.yaml
> @@ -0,0 +1,169 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/nxp,s32-pcie.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP S32G2xx/S32G3xx PCIe controller
> +
> +maintainers:
> + - Bogdan Hamciuc <bogdan.hamciuc@....com>
> + - Ionut Vicovan <ionut.vicovan@....com>
> +
> +description:
> + This PCIe controller is based on the Synopsys DesignWare PCIe IP.
> + The S32G SoC family has two PCIe controllers, which can be configured as
> + either Root Complex or End Point.
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - nxp,s32g2-pcie # S32G2 SoCs RC mode
> + - items:
> + - const: nxp,s32g3-pcie
> + - const: nxp,s32g2-pcie
> +
> + reg:
> + minItems: 7
If minItems is the same maxItems, needn't minItems.
> + maxItems: 7
> +
> + reg-names:
> + items:
> + - const: dbi
> + - const: dbi2
> + - const: atu
> + - const: dma
> + - const: ctrl
> + - const: config
> + - const: addr_space
> +
> + interrupts:
> + minItems: 8
> + maxItems: 8
> +
> + interrupt-names:
> + items:
> + - const: link_req_stat
> + - const: dma
> + - const: msi
> + - const: phy_link_down
> + - const: phy_link_up
> + - const: misc
> + - const: pcs
> + - const: tlp_req_no_comp
use - for names
> +
> + msi-parent:
> + description:
> + Use this option to reference the GIC controller node which will
> + handle the MSIs. This property can be used only in Root Complex mode.
> + The msi-parent node must be declared as "msi-controller" and the list of
> + available SPIs that can be used must be declared using "mbi-ranges".
> + If "msi-parent" is not present in the PCIe node, MSIs will be handled
> + by iMSI-RX -Integrated MSI Receiver [AXI Bridge]-, an integrated
> + MSI reception module in the PCIe controller's AXI Bridge which
> + detects and terminates inbound MSI requests (received on the RX wire).
> + These MSIs no longer appear on the AXI bus, instead a hard-wired
> + interrupt is raised, documented as "DSP AXI MSI Interrupt" in the SoC
> + Reference Manual.
Don't need description for this common property.
msi-parent for pcie devices is most likely wrong. It should use msi-map.
> +
> + nxp,phy-mode:
> + $ref: /schemas/types.yaml#/definitions/string
> + description: Select PHY mode for PCIe controller
> + enum:
> + - crns # Common Reference Clock, No Spread Spectrum
> + - crss # Common Reference Clock, Spread Spectrum
> + - srns # Separate reference Clock, No Spread Spectrum
> + - sris # Separate Reference Clock, Independent Spread Spectrum
> +
> + max-link-speed:
> + description:
> + The max link speed is normaly Gen3, but can be enforced to a lower value
> + in case of special limitations.
needn't description here.
> + maximum: 3
> +
> + num-lanes:
> + description:
> + Max bus width (1 or 2); it is the number of physical lanes
needn't description here.
> + minimum: 1
> + maximum: 2
> +
> +allOf:
> + - $ref: /schemas/pci/snps,dw-pcie-common.yaml#
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - interrupts
> + - interrupt-names
> + - ranges
> + - nxp,phy-mode
> + - num-lanes
> + - phys
> +
> +additionalProperties: true
unevaluatedProperties: false
because you refs to /schemas/pci/snps,dw-pcie-common.yaml
You can send to me do internal review before you post to upstream.
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/phy/phy.h>
> +
> + bus {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + pcie0: pcie@...00000 {
Needn't label "pcie0"
> + compatible = "nxp,s32g3-pcie",
> + "nxp,s32g2-pcie";
> + dma-coherent;
> + reg = <0x00 0x40400000 0x0 0x00001000>, /* dbi registers */
> + <0x00 0x40420000 0x0 0x00001000>, /* dbi2 registers */
> + <0x00 0x40460000 0x0 0x00001000>, /* atu registers */
> + <0x00 0x40470000 0x0 0x00001000>, /* dma registers */
> + <0x00 0x40481000 0x0 0x000000f8>, /* ctrl registers */
> + /* RC configuration space, 4KB each for cfg0 and cfg1
> + * at the end of the outbound memory map
> + */
> + <0x5f 0xffffe000 0x0 0x00002000>,
> + <0x58 0x00000000 0x0 0x40000000>; /* 1GB EP addr space */
> + reg-names = "dbi", "dbi2", "atu", "dma", "ctrl",
> + "config", "addr_space";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges =
> + /* downstream I/O, 64KB and aligned naturally just
> + * before the config space to minimize fragmentation
> + */
> + <0x81000000 0x0 0x00000000 0x5f 0xfffe0000 0x0 0x00010000>,
> + /* non-prefetchable memory, with best case size and
> + * alignment
> + */
> + <0x82000000 0x0 0x00000000 0x58 0x00000000 0x7 0xfffe0000>;
> +
> + nxp,phy-mode = "crns";
> + bus-range = <0x0 0xff>;
> + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "link_req_stat", "dma", "msi",
> + "phy_link_down", "phy_link_up", "misc",
> + "pcs", "tlp_req_no_comp";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &gic 0 0 0 128 4>,
> + <0 0 0 2 &gic 0 0 0 129 4>,
> + <0 0 0 3 &gic 0 0 0 130 4>,
> + <0 0 0 4 &gic 0 0 0 131 4>;
use pre define macro
<0 0 0 1 &gic GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
> + msi-parent = <&gic>;
Suppose it is wrong for pcie
you should use msi-map
Frank
> +
> + num-lanes = <2>;
> + phys = <&serdes0 PHY_TYPE_PCIE 0 0>;
> + };
> + };
> --
> 2.43.0
>
Powered by blists - more mailing lists