Message-Id: <20250912-sound-v1-3-cc9cfd9f2d01@uniontech.com>
Date: Fri, 12 Sep 2025 14:22:37 +0800
From: Cryolitia PukNgae via B4 Relay <devnull+cryolitia.uniontech.com@...nel.org>
To: Jaroslav Kysela <perex@...ex.cz>, Takashi Iwai <tiwai@...e.com>, 
 Jonathan Corbet <corbet@....net>
Cc: linux-sound@...r.kernel.org, linux-usb@...r.kernel.org, 
 linux-kernel@...r.kernel.org, linux-doc@...r.kernel.org, 
 Mingcong Bai <jeffbai@...c.io>, Kexy Biscuit <kexybiscuit@...c.io>, 
 Nie Cheng <niecheng1@...ontech.com>, Zhan Jun <zhanjun@...ontech.com>, 
 Feng Yuan <fengyuan@...ontech.com>, qaqland <anguoli@...ontech.com>, 
 kernel@...ontech.com, Cryolitia PukNgae <cryolitia@...ontech.com>
Subject: [PATCH 3/3] ALSA: doc: add docs about device_device_quirk_flags in
 snd-usb-audio

From: Cryolitia PukNgae <cryolitia@...ontech.com>

Just briefly described about the new option.

Signed-off-by: Cryolitia PukNgae <cryolitia@...ontech.com>
---
 Documentation/sound/alsa-configuration.rst | 105 ++++++++++++++++++++---------
 1 file changed, 73 insertions(+), 32 deletions(-)

diff --git a/Documentation/sound/alsa-configuration.rst b/Documentation/sound/alsa-configuration.rst
index a2fb8ed251dd0294e7a62209ca15d5c32c6adfae..060dfbd4197d3134f20d3d86300d97b14071eee9 100644
--- a/Documentation/sound/alsa-configuration.rst
+++ b/Documentation/sound/alsa-configuration.rst
@@ -2296,40 +2296,81 @@ skip_validation
     The option is used to ignore the validation errors with the hexdump
     of the unit descriptor instead of a driver probe error, so that we
     can check its details.
+device_device_quirk_flags
+    The option povides a refined and flexible control for applying quirk
+    flags.  It allows to specify the quirk flags for each device, and could
+    be modified dynamically via sysfs.
+    The option accepts a string in the format of ``VID1:PID1:FLAGS1;VID2:PID2:
+    FLAGS2;...``, where ``VIDx`` and ``PIDx`` specify the device, and
+    ``FLAGSx`` specify the flags to be applied.  ``VIDx`` and ``PIDx`` are
+    4-digit hexadecimal numbers, and could be specified as ``*`` to match any
+    value.  ``FLAGSx`` could be a set of flags given by name, separated by
+    comma, or a hexadecimal number representing the bit flags.  The available
+    flag names are listed above.  An exclamation mark could be prefixed to a
+    flag name to negate the flag. For example,
+    ``1234:abcd:mixer_playback_min_mute,!ignore_ctl_error;*:*:0x01;``
+    applies the ``mixer_playback_min_mute`` flag and clears the
+    ``ignore_ctl_error`` flag for the device 1234:abcd, and applies
+    the ``skip_sample_rate`` flag for all devices.
 quirk_flags
     Contains the bit flags for various device specific workarounds.
     Applied to the corresponding card index.
 
-        * bit 0: Skip reading sample rate for devices
-        * bit 1: Create Media Controller API entries
-        * bit 2: Allow alignment on audio sub-slot at transfer
-        * bit 3: Add length specifier to transfers
-        * bit 4: Start playback stream at first in implement feedback mode
-        * bit 5: Skip clock selector setup
-        * bit 6: Ignore errors from clock source search
-        * bit 7: Indicates ITF-USB DSD based DACs
-        * bit 8: Add a delay of 20ms at each control message handling
-        * bit 9: Add a delay of 1-2ms at each control message handling
-        * bit 10: Add a delay of 5-6ms at each control message handling
-        * bit 11: Add a delay of 50ms at each interface setup
-        * bit 12: Perform sample rate validations at probe
-        * bit 13: Disable runtime PM autosuspend
-        * bit 14: Ignore errors for mixer access
-        * bit 15: Support generic DSD raw U32_BE format
-        * bit 16: Set up the interface at first like UAC1
-        * bit 17: Apply the generic implicit feedback sync mode
-        * bit 18: Don't apply implicit feedback sync mode
-        * bit 19: Don't closed interface during setting sample rate
-        * bit 20: Force an interface reset whenever stopping & restarting
-          a stream
-        * bit 21: Do not set PCM rate (frequency) when only one rate is
-          available for the given endpoint.
-        * bit 22: Set the fixed resolution 16 for Mic Capture Volume
-        * bit 23: Set the fixed resolution 384 for Mic Capture Volume
-        * bit 24: Set minimum volume control value as mute for devices
-          where the lowest playback value represents muted state instead
-          of minimum audible volume
-        * bit 25: Be similar to bit 24 but for capture streams
+        * bit 0: ``get_sample_rate``
+          Skip reading sample rate for devices
+        * bit 1: ``share_media_device``
+          Create Media Controller API entries
+        * bit 2: ``align_transfer``
+          Allow alignment on audio sub-slot at transfer
+        * bit 3: ``tx_length``
+          Add length specifier to transfers
+        * bit 4: ``playback_first``
+          Start playback stream at first in implement feedback mode
+        * bit 5: ``skip_clock_selector``
+          Skip clock selector setup
+        * bit 6: ``ignore_clock_source``
+          Ignore errors from clock source search
+        * bit 7: ``itf_usb_dsd_dac``
+          Indicates ITF-USB DSD based DACs
+        * bit 8: ``ctl_msg_delay``
+          Add a delay of 20ms at each control message handling
+        * bit 9: ``ctl_msg_delay_1m``
+          Add a delay of 1-2ms at each control message handling
+        * bit 10: ``ctl_msg_delay_5m``
+          Add a delay of 5-6ms at each control message handling
+        * bit 11: ``iface_delay``
+          Add a delay of 50ms at each interface setup
+        * bit 12: ``validate_rates``
+          Perform sample rate validations at probe
+        * bit 13: ``disable_autosuspend``
+          Disable runtime PM autosuspend
+        * bit 14: ``ignore_ctl_error``
+          Ignore errors for mixer access
+        * bit 15: ``dsd_raw``
+          Support generic DSD raw U32_BE format
+        * bit 16: ``set_iface_first``
+          Set up the interface at first like UAC1
+        * bit 17: ``generic_implicit_fb``
+          Apply the generic implicit feedback sync mode
+        * bit 18: ``skip_implicit_fb``
+          Don't apply implicit feedback sync mode
+        * bit 19: ``iface_skip_close``
+          Don't closed interface during setting sample rate
+        * bit 20: ``force_iface_reset``
+          Force an interface reset whenever stopping & restarting a stream
+        * bit 21: ``fixed_rate``
+          Do not set PCM rate (frequency) when only one rate is available
+          for the given endpoint
+        * bit 22: ``mic_res_16``
+          Set the fixed resolution 16 for Mic Capture Volume
+        * bit 23: ``mic_res_384``
+          Set the fixed resolution 384 for Mic Capture Volume
+        * bit 24: ``mixer_playback_min_mute``
+          Set minimum volume control value as mute for devices where the
+          lowest playback value represents muted state instead of minimum
+          audible volume
+        * bit 25: ``mixer_capture_min_mute``
+          Be similar to bit 24 but for capture streams
 
 This module supports multiple devices, autoprobe and hotplugging.
 
@@ -2344,8 +2385,8 @@ report it to the upstream.
 NB: ``quirk_alias`` option is provided only for testing / development.
 If you want to have a proper support, contact to upstream for
 adding the matching quirk in the driver code statically.
-Ditto for ``quirk_flags``.  If a device is known to require specific
-workarounds, please report to the upstream.
+Ditto for ``quirk_flags`` and ``device_device_quirk_flags``.  If a device
+is known to require specific workarounds, please report to the upstream.
 
 Module snd-usb-caiaq
 --------------------

-- 
2.51.0

Powered by blists - more mailing lists