lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <73d30c0c2fb56582c51b6ff9dea3f5145ed36c34.1759824376.git.mazziesaccount@gmail.com>
Date: Tue, 7 Oct 2025 11:32:56 +0300
From: Matti Vaittinen <mazziesaccount@...il.com>
To: Matti Vaittinen <mazziesaccount@...il.com>,
	Matti Vaittinen <matti.vaittinen@...rohmeurope.com>
Cc: Lee Jones <lee@...nel.org>, Pavel Machek <pavel@...nel.org>,
	Rob Herring <robh@...nel.org>,
	Krzysztof Kozlowski <krzk+dt@...nel.org>,
	Conor Dooley <conor+dt@...nel.org>,
	Sebastian Reichel <sre@...nel.org>,
	Liam Girdwood <lgirdwood@...il.com>,
	Mark Brown <broonie@...nel.org>,
	Linus Walleij <linus.walleij@...aro.org>,
	Bartosz Golaszewski <brgl@...ev.pl>,
	Matti Vaittinen <mazziesaccount@...il.com>,
	Andreas Kemnade <andreas@...nade.info>, linux-leds@...r.kernel.org,
	devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
	linux-pm@...r.kernel.org, linux-gpio@...r.kernel.org
Subject: [RFC PATCH 01/13] dt-bindings: regulator: ROHM BD72720

The ROHM BD72720 is a new PMIC with 10 BUCk and 11 LDO regulators.

The BD72720 is designed to support using the BUCK10 as a supply for
the LDOs 1 to 4. When the BUCK10 is used for this, it can be set to a
LDON_HEAD mode. In this mode, the BUCK10 voltage can't be controlled by
software, but the voltage is adjusted by PMIC to match the LDO1 .. LDO4
voltages with a given offset. Offset can be 50mV .. 300mV and is
changeable at 50mV steps.

Add 'ldon-head-millivolt' property to denote a board which is designed
to utilize the LDON_HEAD mode.

All other properties are already existing.

Add dt-binding doc for ROHM BD72720 regulators to make it usable.

Signed-off-by: Matti Vaittinen <mazziesaccount@...il.com>
---
 .../regulator/rohm,bd72720-regulator.yaml     | 153 ++++++++++++++++++
 1 file changed, 153 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd72720-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd72720-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd72720-regulator.yaml
new file mode 100644
index 000000000000..665086f56928
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd72720-regulator.yaml
@@ -0,0 +1,153 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/rohm,bd72720-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD72720 Power Management Integrated Circuit regulators
+
+maintainers:
+  - Matti Vaittinen <mazziesaccount@...il.com>
+
+description: |
+  This module is part of the ROHM BD72720 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd72720-pmic.yaml.
+
+  The regulator controller is represented as a sub-node of the PMIC node
+  on the device tree.
+
+  Regulator nodes should be named to BUCK_<number> and LDO_<number>.
+  The valid names for BD72720 regulator nodes are
+  buck1, buck2, buck3, buck4, buck5, buck6, buck7, buck8, buck9, buck10
+  ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10, ldo11
+
+patternProperties:
+  "^ldo[1-11]$":
+    type: object
+    description:
+      Properties for single LDO regulator.
+    $ref: regulator.yaml#
+
+    properties:
+      regulator-name:
+        pattern: "^ldo[1-11]$"
+        description:
+          should be "ldo1", ..., "ldo11"
+
+      rohm,dvs-run-voltage:
+        description:
+          PMIC default "RUN" state voltage in uV. See below table for
+          LDOs which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-idle-voltage:
+        description:
+          PMIC default "IDLE" state voltage in uV. See below table for
+          LDOs which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-suspend-voltage:
+        description:
+          PMIC default "SUSPEND" state voltage in uV. See below table for
+          LDOs which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-lpsr-voltage:
+        description:
+          PMIC default "deep-idle" state voltage in uV. See below table for
+          LDOs which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+        # Supported default DVS states:
+        #     ldo        |    run     |   idle    | suspend   | lpsr
+        # --------------------------------------------------------------
+        # 1, 2, 3, and 4 | supported  | supported | supported | supported
+        # --------------------------------------------------------------
+        # 5 - 11         |                    supported (*)
+        # --------------------------------------------------------------
+        #
+        # (*) All states use same voltage but have own enable / disable
+        #      settings. Voltage 0 can be specified for a state to make
+        #      regulator disabled on that state.
+
+    unevaluatedProperties: false
+
+  "^buck[1-10]$":
+    type: object
+    description:
+      Properties for single BUCK regulator.
+    $ref: regulator.yaml#
+
+    properties:
+      regulator-name:
+        pattern: "^buck[1-10]$"
+        description:
+          should be "buck1", ..., "buck10"
+
+      rohm,ldon-head-millivolt:
+        description:
+          Set this on boards where BUCK10 is used to supply LDOs 1-4. The bucki
+          voltage will be changed by the PMIC to follow the LDO output voltages
+          with the offset voltage given here. This will improve the LDO efficiency.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 50
+        maximum: 300
+
+      rohm,dvs-run-voltage:
+        description:
+          PMIC default "RUN" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-idle-voltage:
+        description:
+          PMIC default "IDLE" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-suspend-voltage:
+        description:
+          PMIC default "SUSPEND" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-lpsr-voltage:
+        description:
+          PMIC default "deep-idle" state voltage in uV. See below table for
+          bucks which support this. 0 means disabled.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3300000
+
+        # Supported default DVS states:
+        #     buck       |    run     |   idle    | suspend   | lpsr
+        # --------------------------------------------------------------
+        # 1, 2, 3, and 4 | supported  | supported | supported | supported
+        # --------------------------------------------------------------
+        # 5 - 10    |                    supported (*)
+        # --------------------------------------------------------------
+        #
+        # (*) All states use same voltage but have own enable / disable
+        #      settings. Voltage 0 can be specified for a state to make
+        #      regulator disabled on that state.
+
+    required:
+      - regulator-name
+
+    unevaluatedProperties: false
+
+additionalProperties: false
-- 
2.51.0


Download attachment "signature.asc" of type "application/pgp-signature" (489 bytes)

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ