| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20251021050830.185626-2-joan.na@analog.com>
Date: Tue, 21 Oct 2025 14:08:29 +0900
From: Joan-Na-adi <joan.na.devcode@...il.com>
To: Liam Girdwood <lgirdwood@...il.com>
Cc: Mark Brown <broonie@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org,
Joan Na <joan.na@...log.com>
Subject: [PATCH v4 1/2] dt-bindings: regulator: Add MAX77675 regulator binding
From: Joan Na <joan.na@...log.com>
Add device tree binding YAML schema for the Maxim MAX77675 PMIC regulator.
This defines the node properties and supported regulator names for use
in device tree sources.
Signed-off-by: Joan Na <joan.na@...log.com>
---
.../bindings/regulator/maxim,max77675.yaml | 195 ++++++++++++++++++
1 file changed, 195 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/maxim,max77675.yaml
diff --git a/Documentation/devicetree/bindings/regulator/maxim,max77675.yaml b/Documentation/devicetree/bindings/regulator/maxim,max77675.yaml
new file mode 100644
index 000000000000..0ec0844b6d64
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/maxim,max77675.yaml
@@ -0,0 +1,195 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/maxim,max77675.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX77675 PMIC Regulator
+
+maintainers:
+ - Joan Na <joan.na@...log.com>
+
+description: |
+ The MAX77675 is a PMIC providing multiple switching buck regulators
+ (SBB0–SBB3), accessible via I2C. Each SBB can be configured individually
+ in the Device Tree. Additional PMIC settings can be configured through
+ device-specific properties.
+
+properties:
+ compatible:
+ const: maxim,max77675
+
+ reg:
+ maxItems: 1
+
+ maxim,en-mode:
+ description: |
+ Enable mode configuration.
+ The debounce time set by 'maxim,en-debounce-time-us' applies to
+ both push-button and slide-switch modes.
+ "push-button" - A long press triggers power-on or power-down
+ "slide-switch" - Low level powers on, high level powers down
+ "logic" - Low level powers on, high level powers down (no debounce time)
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [push-button, slide-switch, logic]
+ default: slide-switch
+
+ maxim,voltage-change-latency-us:
+ description: |
+ Specifies the delay (in microseconds) between an output voltage change request
+ and the start of the SBB voltage ramp.
+ Use 10us for low-latency or 100us for high-latency (default).
+ enum: [10, 100]
+ default: 100
+
+ maxim,drv-sbb-strength:
+ description: |
+ SIMO Buck-Boost Drive Strength Trim.
+ Controls the drive strength of the SIMO regulator's power MOSFETs.
+ This setting affects the switching speed, which impacts power efficiency and EMI.
+ "max" – Maximum drive strength (~0.6 ns transition time)
+ "high" – High drive strength (~1.2 ns transition time)
+ "low" – Low drive strength (~1.8 ns transition time)
+ "min" – Minimum drive strength (~8 ns transition time)
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [max, high, low, min]
+ default: max
+
+ maxim,dvs-slew-rate-mv-per-us:
+ description: |
+ Dynamic rising slew rate for output voltage transitions, in mV/μs.
+ This setting is only used when 'maxim,fixed-slew-rate' is not present.
+ enum: [5, 10]
+ default: 5
+
+ maxim,en-debounce-time-us:
+ description: Debounce time for the enable pin, in microseconds
+ enum: [100, 30000]
+ default: 100
+
+ maxim,manual-reset-time-sec:
+ description: Manual reset time in seconds
+ enum: [4, 8, 12, 16]
+ default: 4
+
+ maxim,en-pullup-disable:
+ type: boolean
+ description: |
+ Disable internal pull-up for EN pin.
+ When set, the internal pull-up is disabled.
+ Defaults to enabled if this property is not specified.
+ default: false
+
+ maxim,bias-low-power-request:
+ type: boolean
+ description: |
+ Request low-power bias mode.
+ When set, the device enters low-power bias mode.
+ Defaults to normal bias mode if this property is not specified.
+ default: false
+
+ maxim,simo-int-ldo-always-on:
+ type: boolean
+ description: |
+ Set internal LDO to always supply 1.8V
+ When set, the internal LDO always supplies 1.8V.
+ By default, the SIMO internal channel supplies 1.8V during low-power mode
+ default: false
+
+ regulators:
+ type: object
+ description: Regulator child nodes
+ patternProperties:
+ "^sbb[0-3]$":
+ type: object
+ $ref: regulator.yaml#
+ properties:
+ maxim,fps-slot:
+ description: |
+ FPS (Flexible Power Sequencer) slot selection.
+ The Flexible Power Sequencer allows resources to power up under hardware or software control
+ Additionally, each resource can power up independently or among a group of other regulators
+ with adjustable power-up and power-down slots.
+ This device's regulators provide an additional property to configure the FPS parameters,
+ allowing each regulator to be assigned to an FPS slot for proper power management control.
+ "slot0" - Assign to FPS Slot 0
+ "slot1" - Assign to FPS Slot 1
+ "slot2" - Assign to FPS Slot 2
+ "slot3" - Assign to FPS Slot 3
+ "default" - Use the default FPS slot value stored in OTP and read from the register
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [slot0, slot1, slot2, slot3, default]
+ default: default
+
+ maxim,fixed-slew-rate:
+ type: boolean
+ description: |
+ Use fixed slew rate of 2 mV/μs for output voltage transitions.
+ When this property is present, the device uses a constant 2 mV/μs slew rate
+ and ignores any dynamic slew rate configuration.
+ When absent, the device uses the dynamic slew rate specified
+ by 'maxim,dvs-slew-rate-mv-per-us'
+ default: true
+
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ max77675: pmic@44 {
+ compatible = "maxim,max77675";
+ reg = <0x44>;
+
+ maxim,en-mode = "slide-switch";
+ maxim,voltage-change-latency-us = <100>;
+ maxim,drv-sbb-strength = "max";
+ maxim,dvs-slew-rate-mv-per-us = <5>;
+ maxim,manual-reset-time-sec = <4>;
+ maxim,en-debounce-time-us = <100>;
+
+ regulators {
+ sbb0: sbb0 {
+ regulator-name = "sbb0";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <5500000>;
+ maxim,fps-slot = "default";
+ maxim,fixed-slew-rate;
+ };
+
+ sbb1: sbb1 {
+ regulator-name = "sbb1";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <5500000>;
+ maxim,fps-slot = "default";
+ maxim,fixed-slew-rate;
+ };
+
+ sbb2: sbb2 {
+ regulator-name = "sbb2";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <5500000>;
+ maxim,fps-slot = "default";
+ maxim,fixed-slew-rate;
+ };
+
+ sbb3: sbb3 {
+ regulator-name = "sbb3";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <5500000>;
+ maxim,fps-slot = "default";
+ maxim,fixed-slew-rate;
+ };
+ };
+ };
+ };
+
--
2.34.1
Powered by blists - more mailing lists