linux-kernel - [PATCH v2 4/5] clk: amlogic: Optimize PLL enable timing

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20251030-optimize_pll_driver-v2-4-37273f5b25ab@amlogic.com>
Date: Thu, 30 Oct 2025 13:24:14 +0800
From: Chuan Liu via B4 Relay <devnull+chuan.liu.amlogic.com@...nel.org>
To: Neil Armstrong <neil.armstrong@...aro.org>, 
 Jerome Brunet <jbrunet@...libre.com>, 
 Michael Turquette <mturquette@...libre.com>, 
 Stephen Boyd <sboyd@...nel.org>, Kevin Hilman <khilman@...libre.com>, 
 Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Cc: linux-amlogic@...ts.infradead.org, linux-clk@...r.kernel.org, 
 linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org, 
 Chuan Liu <chuan.liu@...ogic.com>, da@...re.computer
Subject: [PATCH v2 4/5] clk: amlogic: Optimize PLL enable timing

From: Chuan Liu <chuan.liu@...ogic.com>

l_detect controls the enablement of the PLL lock detection module.
It should remain disabled while the internal PLL circuits are
reaching a steady state; otherwise, the lock signal may be falsely
triggered high.

Before enabling the internal power supply of the PLL, l_detect should
be disabled. After the PLL’s internal circuits have stabilized,
l_detect should be enabled to prevent false lock signal triggers.

Currently, only A1 supports both l_detect and current_en, so this
patch will only affect A1.

Signed-off-by: Chuan Liu <chuan.liu@...ogic.com>
---
 drivers/clk/meson/clk-pll.c | 28 +++++++++++++++-------------
 1 file changed, 15 insertions(+), 13 deletions(-)

diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
index 6c794adb8ccd..c6eebde1f516 100644
--- a/drivers/clk/meson/clk-pll.c
+++ b/drivers/clk/meson/clk-pll.c
@@ -383,36 +383,38 @@ static int meson_clk_pll_enable(struct clk_hw *hw)
 	if (MESON_PARM_APPLICABLE(&pll->rst))
 		meson_parm_write(clk->map, &pll->rst, 1);
 
+	/* Disable the PLL lock-detect module */
+	if (MESON_PARM_APPLICABLE(&pll->l_detect))
+		meson_parm_write(clk->map, &pll->l_detect, 1);
+
 	/* Enable the pll */
 	meson_parm_write(clk->map, &pll->en, 1);
 	/* Wait for Bandgap and LDO to power up and stabilize */
 	udelay(20);
 
-	/* Take the pll out reset */
-	if (MESON_PARM_APPLICABLE(&pll->rst))
-		meson_parm_write(clk->map, &pll->rst, 0);
-
-	/* Wait for PLL loop stabilization */
-	udelay(20);
-
 	/*
 	 * Compared with the previous SoCs, self-adaption current module
 	 * is newly added for A1, keep the new power-on sequence to enable the
 	 * PLL. The sequence is:
-	 * 1. enable the pll, delay for 10us
+	 * 1. enable the pll, delay for 20us
 	 * 2. enable the pll self-adaption current module, delay for 40us
 	 * 3. enable the lock detect module
 	 */
 	if (MESON_PARM_APPLICABLE(&pll->current_en)) {
-		udelay(10);
 		meson_parm_write(clk->map, &pll->current_en, 1);
-		udelay(40);
+		udelay(20);
 	}
 
-	if (MESON_PARM_APPLICABLE(&pll->l_detect)) {
-		meson_parm_write(clk->map, &pll->l_detect, 1);
+	/* Take the pll out reset */
+	if (MESON_PARM_APPLICABLE(&pll->rst))
+		meson_parm_write(clk->map, &pll->rst, 0);
+
+	/* Wait for PLL loop stabilization */
+	udelay(20);
+
+	/* Enable the lock-detect module */
+	if (MESON_PARM_APPLICABLE(&pll->l_detect))
 		meson_parm_write(clk->map, &pll->l_detect, 0);
-	}
 
 	if (meson_clk_pll_wait_lock(hw)) {
 		/* disable PLL when PLL lock failed. */

-- 
2.42.0