| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <9d968cdd-d7d8-8337-c17c-a8f06e2e182f@linux.intel.com>
Date: Wed, 5 Nov 2025 16:24:42 +0200 (EET)
From: Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
To: Armin Wolf <W_Armin@....de>
cc: Hans de Goede <hansg@...nel.org>, chumuzero@...il.com, corbet@....net,
cs@...edo.de, wse@...edocomputers.com, ggo@...edocomputers.com,
linux-doc@...r.kernel.org, LKML <linux-kernel@...r.kernel.org>,
platform-driver-x86@...r.kernel.org, rdunlap@...radead.org,
alok.a.tiwari@...cle.com, linux-leds@...r.kernel.org, lee@...nel.org,
pobrn@...tonmail.com, nathan@...nel.org
Subject: Re: [PATCH v6 1/2] platform/x86: Add Uniwill laptop driver
On Sun, 2 Nov 2025, Armin Wolf wrote:
> Add a new driver for Uniwill laptops. The driver uses a ACPI
> interface to talk with the embedded controller, but relies on a
> ACPI WMI interface for receiving event notifications.
>
> The driver is reverse-engineered based on the following information:
> - OEM software from intel
> - https://github.com/pobrn/qc71_laptop
> - https://gitlab.com/tuxedocomputers/development/packages/tuxedo-drivers
> - https://github.com/tuxedocomputers/tuxedo-control-center
>
> The underlying EC supports various features, including hwmon sensors,
> battery charge limiting, a RGB lightbar and keyboard-related controls.
>
> Reported-by: cyear <chumuzero@...il.com>
> Closes: https://github.com/lm-sensors/lm-sensors/issues/508
> Closes: https://github.com/Wer-Wolf/uniwill-laptop/issues/3
> Tested-by: Werner Sembach <wse@...edocomputers.com>
> Signed-off-by: Armin Wolf <W_Armin@....de>
> ---
> .../ABI/testing/sysfs-driver-uniwill-laptop | 53 +
> Documentation/wmi/devices/uniwill-laptop.rst | 198 +++
> MAINTAINERS | 10 +
> drivers/platform/x86/Kconfig | 2 +
> drivers/platform/x86/Makefile | 3 +
> drivers/platform/x86/uniwill/Kconfig | 38 +
> drivers/platform/x86/uniwill/Makefile | 8 +
> drivers/platform/x86/uniwill/uniwill-acpi.c | 1550 +++++++++++++++++
> drivers/platform/x86/uniwill/uniwill-wmi.c | 92 +
> drivers/platform/x86/uniwill/uniwill-wmi.h | 127 ++
> 10 files changed, 2081 insertions(+)
> create mode 100644 Documentation/ABI/testing/sysfs-driver-uniwill-laptop
> create mode 100644 Documentation/wmi/devices/uniwill-laptop.rst
> create mode 100644 drivers/platform/x86/uniwill/Kconfig
> create mode 100644 drivers/platform/x86/uniwill/Makefile
> create mode 100644 drivers/platform/x86/uniwill/uniwill-acpi.c
> create mode 100644 drivers/platform/x86/uniwill/uniwill-wmi.c
> create mode 100644 drivers/platform/x86/uniwill/uniwill-wmi.h
>
> diff --git a/Documentation/ABI/testing/sysfs-driver-uniwill-laptop b/Documentation/ABI/testing/sysfs-driver-uniwill-laptop
> new file mode 100644
> index 000000000000..eaeb659793d2
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-driver-uniwill-laptop
> @@ -0,0 +1,53 @@
> +What: /sys/bus/platform/devices/INOU0000:XX/fn_lock_toggle_enable
> +Date: November 2025
> +KernelVersion: 6.19
> +Contact: Armin Wolf <W_Armin@....de>
> +Description:
> + Allows userspace applications to enable/disable the FN lock feature
> + of the integrated keyboard by writing "1"/"0" into this file.
> +
> + Reading this file returns the current enable status of the FN lock functionality.
> +
> +What: /sys/bus/platform/devices/INOU0000:XX/super_key_toggle_enable
> +Date: November 2025
> +KernelVersion: 6.19
> +Contact: Armin Wolf <W_Armin@....de>
> +Description:
> + Allows userspace applications to enable/disable the super key functionality
> + of the integrated keyboard by writing "1"/"0" into this file.
> +
> + Reading this file returns the current enable status of the super key functionality.
> +
> +What: /sys/bus/platform/devices/INOU0000:XX/touchpad_toggle_enable
> +Date: November 2025
> +KernelVersion: 6.19
> +Contact: Armin Wolf <W_Armin@....de>
> +Description:
> + Allows userspace applications to enable/disable the touchpad toggle functionality
> + of the integrated touchpad by writing "1"/"0" into this file.
> +
> + Reading this file returns the current enable status of the touchpad toggle
> + functionality.
> +
> +What: /sys/bus/platform/devices/INOU0000:XX/rainbow_animation
> +Date: November 2025
> +KernelVersion: 6.19
> +Contact: Armin Wolf <W_Armin@....de>
> +Description:
> + Forces the integrated lightbar to display a rainbow animation when the machine
> + is not suspended. Writing "1"/"0" into this file enables/disables this
> + functionality.
> +
> + Reading this file returns the current status of the rainbow animation functionality.
> +
> +What: /sys/bus/platform/devices/INOU0000:XX/breathing_in_suspend
> +Date: November 2025
> +KernelVersion: 6.19
> +Contact: Armin Wolf <W_Armin@....de>
> +Description:
> + Causes the integrated lightbar to display a breathing animation when the machine
> + has been suspended and is running on AC power. Writing "1"/"0" into this file
> + enables/disables this functionality.
> +
> + Reading this file returns the current status of the breathing animation
> + functionality.
> diff --git a/Documentation/wmi/devices/uniwill-laptop.rst b/Documentation/wmi/devices/uniwill-laptop.rst
> new file mode 100644
> index 000000000000..e246bf293450
> --- /dev/null
> +++ b/Documentation/wmi/devices/uniwill-laptop.rst
> @@ -0,0 +1,198 @@
> +.. SPDX-License-Identifier: GPL-2.0-or-later
> +
> +========================================
> +Uniwill Notebook driver (uniwill-laptop)
> +========================================
> +
> +Introduction
> +============
> +
> +Many notebooks manufactured by Uniwill (either directly or as ODM) provide a EC interface
> +for controlling various platform settings like sensors and fan control. This interface is
> +used by the ``uniwill-laptop`` driver to map those features onto standard kernel interfaces.
> +
> +EC WMI interface description
> +============================
> +
> +The EC WMI interface description can be decoded from the embedded binary MOF (bmof)
> +data using the `bmfdec <https://github.com/pali/bmfdec>`_ utility:
> +
> +::
> +
> + [WMI, Dynamic, Provider("WmiProv"), Locale("MS\\0x409"),
> + Description("Class used to operate methods on a ULong"),
> + guid("{ABBC0F6F-8EA1-11d1-00A0-C90629100000}")]
> + class AcpiTest_MULong {
> + [key, read] string InstanceName;
> + [read] boolean Active;
> +
> + [WmiMethodId(1), Implemented, read, write, Description("Return the contents of a ULong")]
> + void GetULong([out, Description("Ulong Data")] uint32 Data);
> +
> + [WmiMethodId(2), Implemented, read, write, Description("Set the contents of a ULong")]
> + void SetULong([in, Description("Ulong Data")] uint32 Data);
> +
> + [WmiMethodId(3), Implemented, read, write,
> + Description("Generate an event containing ULong data")]
> + void FireULong([in, Description("WMI requires a parameter")] uint32 Hack);
> +
> + [WmiMethodId(4), Implemented, read, write, Description("Get and Set the contents of a ULong")]
> + void GetSetULong([in, Description("Ulong Data")] uint64 Data,
> + [out, Description("Ulong Data")] uint32 Return);
> +
> + [WmiMethodId(5), Implemented, read, write,
> + Description("Get and Set the contents of a ULong for Dollby button")]
> + void GetButton([in, Description("Ulong Data")] uint64 Data,
> + [out, Description("Ulong Data")] uint32 Return);
> + };
> +
> +Most of the WMI-related code was copied from the Windows driver samples, which unfortunately means
> +that the WMI-GUID is not unique. This makes the WMI-GUID unusable for autoloading.
> +
> +WMI method GetULong()
> +---------------------
> +
> +This WMI method was copied from the Windows driver samples and has no function.
> +
> +WMI method SetULong()
> +---------------------
> +
> +This WMI method was copied from the Windows driver samples and has no function.
> +
> +WMI method FireULong()
> +----------------------
> +
> +This WMI method allows to inject a WMI event with a 32-bit payload. Its primary purpose seems
> +to be debugging.
> +
> +WMI method GetSetULong()
> +------------------------
> +
> +This WMI method is used to communicate with the EC. The ``Data`` argument holds the following
> +information (starting with the least significant byte):
> +
> +1. 16-bit address
> +2. 16-bit data (set to ``0x0000`` when reading)
> +3. 16-bit operation (``0x0100`` for reading and ``0x0000`` for writing)
> +4. 16-bit reserved (set to ``0x0000``)
> +
> +The first 8 bits of the ``Return`` value contain the data returned by the EC when reading.
> +The special value ``0xFEFEFEFE`` is used to indicate a communication failure with the EC.
> +
> +WMI method GetButton()
> +----------------------
> +
> +This WMI method is not implemented on all machines and has an unknown purpose.
> +
> +Reverse-Engineering the EC WMI interface
> +========================================
> +
> +.. warning:: Randomly poking the EC can potentially cause damage to the machine and other unwanted
> + side effects, please be careful.
> +
> +The EC behind the ``GetSetULong`` method is used by the OEM software supplied by the manufacturer.
> +Reverse-engineering of this software is difficult since it uses an obfuscator, however some parts
> +are not obfuscated. In this case `dnSpy <https://github.com/dnSpy/dnSpy>`_ could also be helpful.
> +
> +The EC can be accessed under Windows using powershell (requires admin privileges):
> +
> +::
> +
> + > $obj = Get-CimInstance -Namespace root/wmi -ClassName AcpiTest_MULong | Select-Object -First 1
> + > Invoke-CimMethod -InputObject $obj -MethodName GetSetULong -Arguments @{Data = <input>}
> +
> +WMI event interface description
> +===============================
> +
> +The WMI interface description can also be decoded from the embedded binary MOF (bmof)
> +data:
> +
> +::
> +
> + [WMI, Dynamic, Provider("WmiProv"), Locale("MS\\0x409"),
> + Description("Class containing event generated ULong data"),
> + guid("{ABBC0F72-8EA1-11d1-00A0-C90629100000}")]
> + class AcpiTest_EventULong : WmiEvent {
> + [key, read] string InstanceName;
> + [read] boolean Active;
> +
> + [WmiDataId(1), read, write, Description("ULong Data")] uint32 ULong;
> + };
> +
> +Most of the WMI-related code was again copied from the Windows driver samples, causing this WMI
> +interface to suffer from the same restrictions as the EC WMI interface described above.
> +
> +WMI event data
> +--------------
> +
> +The WMI event data contains a single 32-bit value which is used to indicate various platform events.
> +
> +Reverse-Engineering the Uniwill WMI event interface
> +===================================================
> +
> +The driver logs debug messages when receiving a WMI event. Thus enabling debug messages will be
> +useful for finding unknown event codes.
> +
> +EC ACPI interface description
> +=============================
> +
> +The ``INOU0000`` ACPI device is a virtual device used to access various hardware registers
> +available on notebooks manufactured by Uniwill. Reading and writing those registers happens
> +by calling ACPI control methods. The ``uniwill-laptop`` driver uses this device to communicate
> +with the EC because the ACPI control methods are faster than the WMI methods described above.
> +
> +ACPI control methods used for reading registers take a single ACPI integer containing the address
> +of the register to read and return a ACPI integer containing the data inside said register. ACPI
> +control methods used for writing registers however take two ACPI integers, with the additional
> +ACPI integer containing the data to be written into the register. Such ACPI control methods return
> +nothing.
> +
> +System memory
> +-------------
> +
> +System memory can be accessed with a granularity of either a single byte (``MMRB`` for reading and
> +``MMWB`` for writing) or four bytes (``MMRD`` for reading and ``MMWD`` for writing). Those ACPI
> +control methods are unused because they provide no benefit when compared to the native memory
> +access functions provided by the kernel.
> +
> +EC RAM
> +------
> +
> +The internal RAM of the EC can be accessed with a granularity of a single byte using the ``ECRR``
> +(read) and ``ECRW`` (write) ACPI control methods, with the maximum register address being ``0xFFF``.
> +The OEM software waits 6 ms after calling one of those ACPI control methods, likely to avoid
> +overwhelming the EC when being connected over LPC.
> +
> +PCI config space
> +----------------
> +
> +The PCI config space can be accessed with a granularity of four bytes using the ``PCRD`` (read) and
> +``PCWD`` (write) ACPI control methods. The exact address format is unknown, and poking random PCI
> +devices might confuse the PCI subsystem. Because of this those ACPI control methods are not used.
> +
> +IO ports
> +--------
> +
> +IO ports can be accessed with a granularity of four bytes using the ``IORD`` (read) and ``IOWD``
> +(write) ACPI control methods. Those ACPI control methods are unused because they provide no benefit
> +when compared to the native IO port access functions provided by the kernel.
> +
> +CMOS RAM
> +--------
> +
> +The CMOS RAM can be accessed with a granularity of a single byte using the ``RCMS`` (read) and
> +``WCMS`` ACPI control methods. Using those ACPI methods might interfere with the native CMOS RAM
> +access functions provided by the kernel due to the usage of indexed IO, so they are unused.
> +
> +Indexed IO
> +----------
> +
> +Indexed IO with IO ports with a granularity of a single byte can be performed using the ``RIOP``
> +(read) and ``WIOP`` (write) ACPI control methods. Those ACPI methods are unused because they
> +provide no benifit when compared to the native IO port access functions provided by the kernel.
> +
> +Special thanks go to github user `pobrn` which developed the
> +`qc71_laptop <https://github.com/pobrn/qc71_laptop>`_ driver on which this driver is partly based.
> +The same is true for Tuxedo Computers, which developed the
> +`tuxedo-drivers <https://gitlab.com/tuxedocomputers/development/packages/tuxedo-drivers>`_ package
> +which also served as a foundation for this driver.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 46126ce2f968..8fce9b5e9fd7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -26376,6 +26376,16 @@ L: linux-scsi@...r.kernel.org
> S: Maintained
> F: drivers/ufs/host/ufs-renesas.c
>
> +UNIWILL LAPTOP DRIVER
> +M: Armin Wolf <W_Armin@....de>
> +L: platform-driver-x86@...r.kernel.org
> +S: Maintained
> +F: Documentation/ABI/testing/sysfs-driver-uniwill-laptop
> +F: Documentation/wmi/devices/uniwill-laptop.rst
> +F: drivers/platform/x86/uniwill/uniwill-acpi.c
> +F: drivers/platform/x86/uniwill/uniwill-wmi.c
> +F: drivers/platform/x86/uniwill/uniwill-wmi.h
> +
> UNSORTED BLOCK IMAGES (UBI)
> M: Richard Weinberger <richard@....at>
> R: Zhihao Cheng <chengzhihao1@...wei.com>
> diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
> index 46e62feeda3c..1e9b84f1098f 100644
> --- a/drivers/platform/x86/Kconfig
> +++ b/drivers/platform/x86/Kconfig
> @@ -74,6 +74,8 @@ config HUAWEI_WMI
> To compile this driver as a module, choose M here: the module
> will be called huawei-wmi.
>
> +source "drivers/platform/x86/uniwill/Kconfig"
> +
> config UV_SYSFS
> tristate "Sysfs structure for UV systems"
> depends on X86_UV
> diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
> index c7db2a88c11a..d722e244a4a7 100644
> --- a/drivers/platform/x86/Makefile
> +++ b/drivers/platform/x86/Makefile
> @@ -110,6 +110,9 @@ obj-$(CONFIG_TOSHIBA_WMI) += toshiba-wmi.o
> # before toshiba_acpi initializes
> obj-$(CONFIG_ACPI_TOSHIBA) += toshiba_acpi.o
>
> +# Uniwill
> +obj-y += uniwill/
> +
> # Inspur
> obj-$(CONFIG_INSPUR_PLATFORM_PROFILE) += inspur_platform_profile.o
>
> diff --git a/drivers/platform/x86/uniwill/Kconfig b/drivers/platform/x86/uniwill/Kconfig
> new file mode 100644
> index 000000000000..d07cc8440188
> --- /dev/null
> +++ b/drivers/platform/x86/uniwill/Kconfig
> @@ -0,0 +1,38 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +#
> +# Uniwill X86 Platform Specific Drivers
> +#
> +
> +menuconfig X86_PLATFORM_DRIVERS_UNIWILL
> + bool "Uniwill X86 Platform Specific Device Drivers"
> + depends on X86_PLATFORM_DEVICES
> + help
> + Say Y here to see options for device drivers for various
> + Uniwill x86 platforms, including many OEM laptops originally
> + manufactured by Uniwill.
> + This option alone does not add any kernel code.
> +
> + If you say N, all options in this submenu will be skipped and disabled.
> +
> +if X86_PLATFORM_DRIVERS_UNIWILL
> +
> +config UNIWILL_LAPTOP
> + tristate "Uniwill Laptop Extras"
> + default m
> + depends on ACPI
> + depends on ACPI_WMI
> + depends on ACPI_BATTERY
> + depends on HWMON
> + depends on INPUT
> + depends on LEDS_CLASS_MULTICOLOR
> + depends on DMI
> + select REGMAP
> + select INPUT_SPARSEKMAP
> + help
> + This driver adds support for various extra features found on Uniwill laptops,
> + like the lightbar, hwmon sensors and hotkeys. It also supports many OEM laptops
> + originally manufactured by Uniwill.
> +
> + If you have such a laptop, say Y or M here.
> +
> +endif
> diff --git a/drivers/platform/x86/uniwill/Makefile b/drivers/platform/x86/uniwill/Makefile
> new file mode 100644
> index 000000000000..05cd1747a240
> --- /dev/null
> +++ b/drivers/platform/x86/uniwill/Makefile
> @@ -0,0 +1,8 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later
> +#
> +# Makefile for linux/drivers/platform/x86/uniwill
> +# Uniwill X86 Platform Specific Drivers
> +#
> +
> +obj-$(CONFIG_UNIWILL_LAPTOP) += uniwill-laptop.o
> +uniwill-laptop-y := uniwill-acpi.o uniwill-wmi.o
> diff --git a/drivers/platform/x86/uniwill/uniwill-acpi.c b/drivers/platform/x86/uniwill/uniwill-acpi.c
> new file mode 100644
> index 000000000000..014960d16211
> --- /dev/null
> +++ b/drivers/platform/x86/uniwill/uniwill-acpi.c
> @@ -0,0 +1,1550 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Linux driver for Uniwill notebooks.
> + *
> + * Special thanks go to Pőcze Barnabás, Christoffer Sandberg and Werner Sembach
> + * for supporting the development of this driver either through prior work or
> + * by answering questions regarding the underlying ACPI and WMI interfaces.
> + *
> + * Copyright (C) 2025 Armin Wolf <W_Armin@....de>
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/acpi.h>
> +#include <linux/array_size.h>
> +#include <linux/bits.h>
> +#include <linux/bitfield.h>
> +#include <linux/cleanup.h>
> +#include <linux/debugfs.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/device/driver.h>
> +#include <linux/dmi.h>
> +#include <linux/errno.h>
> +#include <linux/fixp-arith.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>
> +#include <linux/init.h>
> +#include <linux/input.h>
> +#include <linux/input/sparse-keymap.h>
> +#include <linux/kernel.h>
> +#include <linux/kstrtox.h>
> +#include <linux/leds.h>
> +#include <linux/led-class-multicolor.h>
> +#include <linux/limits.h>
> +#include <linux/list.h>
> +#include <linux/minmax.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/notifier.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm.h>
> +#include <linux/printk.h>
> +#include <linux/regmap.h>
> +#include <linux/string.h>
> +#include <linux/sysfs.h>
> +#include <linux/types.h>
> +#include <linux/units.h>
> +
> +#include <acpi/battery.h>
> +
> +#include "uniwill-wmi.h"
> +
> +#define EC_ADDR_BAT_POWER_UNIT_1 0x0400
> +
> +#define EC_ADDR_BAT_POWER_UNIT_2 0x0401
> +
> +#define EC_ADDR_BAT_DESIGN_CAPACITY_1 0x0402
> +
> +#define EC_ADDR_BAT_DESIGN_CAPACITY_2 0x0403
> +
> +#define EC_ADDR_BAT_FULL_CAPACITY_1 0x0404
> +
> +#define EC_ADDR_BAT_FULL_CAPACITY_2 0x0405
> +
> +#define EC_ADDR_BAT_DESIGN_VOLTAGE_1 0x0408
> +
> +#define EC_ADDR_BAT_DESIGN_VOLTAGE_2 0x0409
> +
> +#define EC_ADDR_BAT_STATUS_1 0x0432
> +#define BAT_DISCHARGING BIT(0)
> +
> +#define EC_ADDR_BAT_STATUS_2 0x0433
> +
> +#define EC_ADDR_BAT_CURRENT_1 0x0434
> +
> +#define EC_ADDR_BAT_CURRENT_2 0x0435
> +
> +#define EC_ADDR_BAT_REMAIN_CAPACITY_1 0x0436
> +
> +#define EC_ADDR_BAT_REMAIN_CAPACITY_2 0x0437
> +
> +#define EC_ADDR_BAT_VOLTAGE_1 0x0438
> +
> +#define EC_ADDR_BAT_VOLTAGE_2 0x0439
> +
> +#define EC_ADDR_CPU_TEMP 0x043E
> +
> +#define EC_ADDR_GPU_TEMP 0x044F
> +
> +#define EC_ADDR_MAIN_FAN_RPM_1 0x0464
> +
> +#define EC_ADDR_MAIN_FAN_RPM_2 0x0465
> +
> +#define EC_ADDR_SECOND_FAN_RPM_1 0x046C
> +
> +#define EC_ADDR_SECOND_FAN_RPM_2 0x046D
> +
> +#define EC_ADDR_DEVICE_STATUS 0x047B
> +#define WIFI_STATUS_ON BIT(7)
> +/* BIT(5) is also unset depending on the rfkill state (bluetooth?) */
> +
> +#define EC_ADDR_BAT_ALERT 0x0494
> +
> +#define EC_ADDR_BAT_CYCLE_COUNT_1 0x04A6
> +
> +#define EC_ADDR_BAT_CYCLE_COUNT_2 0x04A7
> +
> +#define EC_ADDR_PROJECT_ID 0x0740
> +
> +#define EC_ADDR_AP_OEM 0x0741
> +#define ENABLE_MANUAL_CTRL BIT(0)
> +#define ITE_KBD_EFFECT_REACTIVE BIT(3)
> +#define FAN_ABNORMAL BIT(5)
> +
> +#define EC_ADDR_SUPPORT_5 0x0742
> +#define FAN_TURBO_SUPPORTED BIT(4)
> +#define FAN_SUPPORT BIT(5)
> +
> +#define EC_ADDR_CTGP_DB_CTRL 0x0743
> +#define CTGP_DB_GENERAL_ENABLE BIT(0)
> +#define CTGP_DB_DB_ENABLE BIT(1)
> +#define CTGP_DB_CTGP_ENABLE BIT(2)
> +
> +#define EC_ADDR_CTGP_OFFSET 0x0744
> +
> +#define EC_ADDR_TPP_OFFSET 0x0745
> +
> +#define EC_ADDR_MAX_TGP 0x0746
> +
> +#define EC_ADDR_LIGHTBAR_AC_CTRL 0x0748
> +#define LIGHTBAR_APP_EXISTS BIT(0)
> +#define LIGHTBAR_POWER_SAVE BIT(1)
> +#define LIGHTBAR_S0_OFF BIT(2)
> +#define LIGHTBAR_S3_OFF BIT(3) // Breathing animation when suspended
> +#define LIGHTBAR_WELCOME BIT(7) // Rainbow animation
> +
> +#define EC_ADDR_LIGHTBAR_AC_RED 0x0749
> +
> +#define EC_ADDR_LIGHTBAR_AC_GREEN 0x074A
> +
> +#define EC_ADDR_LIGHTBAR_AC_BLUE 0x074B
> +
> +#define EC_ADDR_BIOS_OEM 0x074E
> +#define FN_LOCK_STATUS BIT(4)
> +
> +#define EC_ADDR_MANUAL_FAN_CTRL 0x0751
> +#define FAN_LEVEL_MASK GENMASK(2, 0)
> +#define FAN_MODE_TURBO BIT(4)
> +#define FAN_MODE_HIGH BIT(5)
> +#define FAN_MODE_BOOST BIT(6)
> +#define FAN_MODE_USER BIT(7)
> +
> +#define EC_ADDR_PWM_1 0x075B
> +
> +#define EC_ADDR_PWM_2 0x075C
> +
> +/* Unreliable */
> +#define EC_ADDR_SUPPORT_1 0x0765
> +#define AIRPLANE_MODE BIT(0)
> +#define GPS_SWITCH BIT(1)
> +#define OVERCLOCK BIT(2)
> +#define MACRO_KEY BIT(3)
> +#define SHORTCUT_KEY BIT(4)
> +#define SUPER_KEY_LOCK BIT(5)
> +#define LIGHTBAR BIT(6)
> +#define FAN_BOOST BIT(7)
> +
> +#define EC_ADDR_SUPPORT_2 0x0766
> +#define SILENT_MODE BIT(0)
> +#define USB_CHARGING BIT(1)
> +#define RGB_KEYBOARD BIT(2)
> +#define CHINA_MODE BIT(5)
> +#define MY_BATTERY BIT(6)
> +
> +#define EC_ADDR_TRIGGER 0x0767
> +#define TRIGGER_SUPER_KEY_LOCK BIT(0)
> +#define TRIGGER_LIGHTBAR BIT(1)
> +#define TRIGGER_FAN_BOOST BIT(2)
> +#define TRIGGER_SILENT_MODE BIT(3)
> +#define TRIGGER_USB_CHARGING BIT(4)
> +#define RGB_APPLY_COLOR BIT(5)
> +#define RGB_LOGO_EFFECT BIT(6)
> +#define RGB_RAINBOW_EFFECT BIT(7)
> +
> +#define EC_ADDR_SWITCH_STATUS 0x0768
> +#define SUPER_KEY_LOCK_STATUS BIT(0)
> +#define LIGHTBAR_STATUS BIT(1)
> +#define FAN_BOOST_STATUS BIT(2)
> +#define MACRO_KEY_STATUS BIT(3)
> +#define MY_BAT_POWER_BAT_STATUS BIT(4)
> +
> +#define EC_ADDR_RGB_RED 0x0769
> +
> +#define EC_ADDR_RGB_GREEN 0x076A
> +
> +#define EC_ADDR_RGB_BLUE 0x076B
> +
> +#define EC_ADDR_ROMID_START 0x0770
> +#define ROMID_LENGTH 14
> +
> +#define EC_ADDR_ROMID_EXTRA_1 0x077E
> +
> +#define EC_ADDR_ROMID_EXTRA_2 0x077F
> +
> +#define EC_ADDR_BIOS_OEM_2 0x0782
> +#define FAN_V2_NEW BIT(0)
> +#define FAN_QKEY BIT(1)
> +#define FAN_TABLE_OFFICE_MODE BIT(2)
> +#define FAN_V3 BIT(3)
> +#define DEFAULT_MODE BIT(4)
> +
> +#define EC_ADDR_PL1_SETTING 0x0783
> +
> +#define EC_ADDR_PL2_SETTING 0x0784
> +
> +#define EC_ADDR_PL4_SETTING 0x0785
> +
> +#define EC_ADDR_FAN_DEFAULT 0x0786
> +#define FAN_CURVE_LENGTH 5
> +
> +#define EC_ADDR_KBD_STATUS 0x078C
> +#define KBD_WHITE_ONLY BIT(0) // ~single color
> +#define KBD_SINGLE_COLOR_OFF BIT(1)
> +#define KBD_TURBO_LEVEL_MASK GENMASK(3, 2)
> +#define KBD_APPLY BIT(4)
> +#define KBD_BRIGHTNESS GENMASK(7, 5)
> +
> +#define EC_ADDR_FAN_CTRL 0x078E
> +#define FAN3P5 BIT(1)
> +#define CHARGING_PROFILE BIT(3)
> +#define UNIVERSAL_FAN_CTRL BIT(6)
> +
> +#define EC_ADDR_BIOS_OEM_3 0x07A3
> +#define FAN_REDUCED_DURY_CYCLE BIT(5)
> +#define FAN_ALWAYS_ON BIT(6)
> +
> +#define EC_ADDR_BIOS_BYTE 0x07A4
> +#define FN_LOCK_SWITCH BIT(3)
> +
> +#define EC_ADDR_OEM_3 0x07A5
> +#define POWER_LED_MASK GENMASK(1, 0)
> +#define POWER_LED_LEFT 0x00
> +#define POWER_LED_BOTH 0x01
> +#define POWER_LED_NONE 0x02
> +#define FAN_QUIET BIT(2)
> +#define OVERBOOST BIT(4)
> +#define HIGH_POWER BIT(7)
> +
> +#define EC_ADDR_OEM_4 0x07A6
> +#define OVERBOOST_DYN_TEMP_OFF BIT(1)
> +#define TOUCHPAD_TOGGLE_OFF BIT(6)
> +
> +#define EC_ADDR_CHARGE_CTRL 0x07B9
> +#define CHARGE_CTRL_MASK GENMASK(6, 0)
> +#define CHARGE_CTRL_REACHED BIT(7)
> +
> +#define EC_ADDR_UNIVERSAL_FAN_CTRL 0x07C5
> +#define SPLIT_TABLES BIT(7)
> +
> +#define EC_ADDR_AP_OEM_6 0x07C6
> +#define ENABLE_UNIVERSAL_FAN_CTRL BIT(2)
> +#define BATTERY_CHARGE_FULL_OVER_24H BIT(3)
> +#define BATTERY_ERM_STATUS_REACHED BIT(4)
> +
> +#define EC_ADDR_CHARGE_PRIO 0x07CC
> +#define CHARGING_PERFORMANCE BIT(7)
> +
> +/* Same bits as EC_ADDR_LIGHTBAR_AC_CTRL except LIGHTBAR_S3_OFF */
> +#define EC_ADDR_LIGHTBAR_BAT_CTRL 0x07E2
> +
> +#define EC_ADDR_LIGHTBAR_BAT_RED 0x07E3
> +
> +#define EC_ADDR_LIGHTBAR_BAT_GREEN 0x07E4
> +
> +#define EC_ADDR_LIGHTBAR_BAT_BLUE 0x07E5
> +
> +#define EC_ADDR_CPU_TEMP_END_TABLE 0x0F00
> +
> +#define EC_ADDR_CPU_TEMP_START_TABLE 0x0F10
> +
> +#define EC_ADDR_CPU_FAN_SPEED_TABLE 0x0F20
> +
> +#define EC_ADDR_GPU_TEMP_END_TABLE 0x0F30
> +
> +#define EC_ADDR_GPU_TEMP_START_TABLE 0x0F40
> +
> +#define EC_ADDR_GPU_FAN_SPEED_TABLE 0x0F50
> +
> +/*
> + * Those two registers technically allow for manual fan control,
> + * but are unstable on some models and are likely not meant to
> + * be used by applications as they are only accessible when using
> + * the WMI interface.
> + */
> +#define EC_ADDR_PWM_1_WRITEABLE 0x1804
> +
> +#define EC_ADDR_PWM_2_WRITEABLE 0x1809
> +
> +#define DRIVER_NAME "uniwill"
> +
> +/*
> + * The OEM software always sleeps up to 6 ms after reading/writing EC
> + * registers, so we emulate this behaviour for maximum compatibility.
> + */
> +#define UNIWILL_EC_DELAY_US 6000
> +
> +#define PWM_MAX 200
> +#define FAN_TABLE_LENGTH 16
> +
> +#define LED_CHANNELS 3
> +#define LED_MAX_BRIGHTNESS 200
> +
> +#define UNIWILL_FEATURE_FN_LOCK_TOGGLE BIT(0)
> +#define UNIWILL_FEATURE_SUPER_KEY_TOGGLE BIT(1)
> +#define UNIWILL_FEATURE_TOUCHPAD_TOGGLE BIT(2)
> +#define UNIWILL_FEATURE_LIGHTBAR BIT(3)
> +#define UNIWILL_FEATURE_BATTERY BIT(4)
> +#define UNIWILL_FEATURE_HWMON BIT(5)
> +
> +struct uniwill_data {
> + struct device *dev;
> + acpi_handle handle;
> + struct regmap *regmap;
> + struct acpi_battery_hook hook;
> + unsigned int last_charge_ctrl;
> + struct mutex battery_lock; /* Protects the list of currently registered batteries */
> + unsigned int last_switch_status;
> + struct mutex super_key_lock; /* Protects the toggling of the super key lock state */
> + struct list_head batteries;
> + struct mutex led_lock; /* Protects writes to the lightbar registers */
> + struct led_classdev_mc led_mc_cdev;
> + struct mc_subled led_mc_subled_info[LED_CHANNELS];
> + struct mutex input_lock; /* Protects input sequence during notify */
> + struct input_dev *input_device;
> + struct notifier_block nb;
> +};
> +
> +struct uniwill_battery_entry {
> + struct list_head head;
> + struct power_supply *battery;
> +};
> +
> +static bool force;
> +module_param_unsafe(force, bool, 0);
> +MODULE_PARM_DESC(force, "Force loading without checking for supported devices\n");
> +
> +/* Feature bitmask since the associated registers are not reliable */
> +static unsigned int supported_features;
> +
> +static const char * const uniwill_temp_labels[] = {
> + "CPU",
> + "GPU",
> +};
> +
> +static const char * const uniwill_fan_labels[] = {
> + "Main",
> + "Secondary",
> +};
> +
> +static const struct key_entry uniwill_keymap[] = {
> + /* Reported via keyboard controller */
> + { KE_IGNORE, UNIWILL_OSD_CAPSLOCK, { KEY_CAPSLOCK }},
> + { KE_IGNORE, UNIWILL_OSD_NUMLOCK, { KEY_NUMLOCK }},
> +
> + /* Reported when the user locks/unlocks the super key */
> + { KE_IGNORE, UNIWILL_OSD_SUPER_KEY_LOCK_ENABLE, { KEY_UNKNOWN }},
> + { KE_IGNORE, UNIWILL_OSD_SUPER_KEY_LOCK_DISABLE, { KEY_UNKNOWN }},
> + /* Optional, might not be reported by all devices */
> + { KE_IGNORE, UNIWILL_OSD_SUPER_KEY_LOCK_CHANGED, { KEY_UNKNOWN }},
> +
> + /* Reported in manual mode when toggling the airplane mode status */
> + { KE_KEY, UNIWILL_OSD_RFKILL, { KEY_RFKILL }},
> +
> + /* Reported when user wants to cycle the platform profile */
> + { KE_IGNORE, UNIWILL_OSD_PERFORMANCE_MODE_TOGGLE, { KEY_UNKNOWN }},
> +
> + /* Reported when the user wants to adjust the brightness of the keyboard */
> + { KE_KEY, UNIWILL_OSD_KBDILLUMDOWN, { KEY_KBDILLUMDOWN }},
> + { KE_KEY, UNIWILL_OSD_KBDILLUMUP, { KEY_KBDILLUMUP }},
> +
> + /* Reported when the user wants to toggle the microphone mute status */
> + { KE_KEY, UNIWILL_OSD_MIC_MUTE, { KEY_MICMUTE }},
> +
> + /* Reported when the user locks/unlocks the Fn key */
> + { KE_IGNORE, UNIWILL_OSD_FN_LOCK, { KEY_FN_ESC }},
> +
> + /* Reported when the user wants to toggle the brightness of the keyboard */
> + { KE_KEY, UNIWILL_OSD_KBDILLUMTOGGLE, { KEY_KBDILLUMTOGGLE }},
> +
> + /* FIXME: find out the exact meaning of those events */
> + { KE_IGNORE, UNIWILL_OSD_BAT_CHARGE_FULL_24_H, { KEY_UNKNOWN }},
> + { KE_IGNORE, UNIWILL_OSD_BAT_ERM_UPDATE, { KEY_UNKNOWN }},
> +
> + /* Reported when the user wants to toggle the benchmark mode status */
> + { KE_IGNORE, UNIWILL_OSD_BENCHMARK_MODE_TOGGLE, { KEY_UNKNOWN }},
> +
> + { KE_END }
> +};
> +
> +static int uniwill_ec_reg_write(void *context, unsigned int reg, unsigned int val)
> +{
> + union acpi_object params[2] = {
> + {
> + .integer = {
> + .type = ACPI_TYPE_INTEGER,
> + .value = reg,
> + },
> + },
> + {
> + .integer = {
> + .type = ACPI_TYPE_INTEGER,
> + .value = val,
> + },
> + },
> + };
> + struct uniwill_data *data = context;
> + struct acpi_object_list input = {
> + .count = ARRAY_SIZE(params),
> + .pointer = params,
> + };
> + acpi_status status;
> +
> + status = acpi_evaluate_object(data->handle, "ECRW", &input, NULL);
> + if (ACPI_FAILURE(status))
> + return -EIO;
> +
> + usleep_range(UNIWILL_EC_DELAY_US, UNIWILL_EC_DELAY_US * 2);
> +
> + return 0;
> +}
> +
> +static int uniwill_ec_reg_read(void *context, unsigned int reg, unsigned int *val)
> +{
> + union acpi_object params[1] = {
> + {
> + .integer = {
> + .type = ACPI_TYPE_INTEGER,
> + .value = reg,
> + },
> + },
> + };
> + struct uniwill_data *data = context;
> + struct acpi_object_list input = {
> + .count = ARRAY_SIZE(params),
> + .pointer = params,
> + };
> + unsigned long long output;
> + acpi_status status;
> +
> + status = acpi_evaluate_integer(data->handle, "ECRR", &input, &output);
> + if (ACPI_FAILURE(status))
> + return -EIO;
> +
> + if (output > U8_MAX)
> + return -ENXIO;
> +
> + usleep_range(UNIWILL_EC_DELAY_US, UNIWILL_EC_DELAY_US * 2);
> +
> + *val = output;
> +
> + return 0;
> +}
> +
> +static const struct regmap_bus uniwill_ec_bus = {
> + .reg_write = uniwill_ec_reg_write,
> + .reg_read = uniwill_ec_reg_read,
> + .reg_format_endian_default = REGMAP_ENDIAN_LITTLE,
> + .val_format_endian_default = REGMAP_ENDIAN_LITTLE,
> +};
> +
> +static bool uniwill_writeable_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case EC_ADDR_AP_OEM:
> + case EC_ADDR_LIGHTBAR_AC_CTRL:
> + case EC_ADDR_LIGHTBAR_AC_RED:
> + case EC_ADDR_LIGHTBAR_AC_GREEN:
> + case EC_ADDR_LIGHTBAR_AC_BLUE:
> + case EC_ADDR_BIOS_OEM:
> + case EC_ADDR_TRIGGER:
> + case EC_ADDR_OEM_4:
> + case EC_ADDR_CHARGE_CTRL:
> + case EC_ADDR_LIGHTBAR_BAT_CTRL:
> + case EC_ADDR_LIGHTBAR_BAT_RED:
> + case EC_ADDR_LIGHTBAR_BAT_GREEN:
> + case EC_ADDR_LIGHTBAR_BAT_BLUE:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static bool uniwill_readable_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case EC_ADDR_CPU_TEMP:
> + case EC_ADDR_GPU_TEMP:
> + case EC_ADDR_MAIN_FAN_RPM_1:
> + case EC_ADDR_MAIN_FAN_RPM_2:
> + case EC_ADDR_SECOND_FAN_RPM_1:
> + case EC_ADDR_SECOND_FAN_RPM_2:
> + case EC_ADDR_BAT_ALERT:
> + case EC_ADDR_PROJECT_ID:
> + case EC_ADDR_AP_OEM:
> + case EC_ADDR_LIGHTBAR_AC_CTRL:
> + case EC_ADDR_LIGHTBAR_AC_RED:
> + case EC_ADDR_LIGHTBAR_AC_GREEN:
> + case EC_ADDR_LIGHTBAR_AC_BLUE:
> + case EC_ADDR_BIOS_OEM:
> + case EC_ADDR_PWM_1:
> + case EC_ADDR_PWM_2:
> + case EC_ADDR_TRIGGER:
> + case EC_ADDR_SWITCH_STATUS:
> + case EC_ADDR_OEM_4:
> + case EC_ADDR_CHARGE_CTRL:
> + case EC_ADDR_LIGHTBAR_BAT_CTRL:
> + case EC_ADDR_LIGHTBAR_BAT_RED:
> + case EC_ADDR_LIGHTBAR_BAT_GREEN:
> + case EC_ADDR_LIGHTBAR_BAT_BLUE:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static bool uniwill_volatile_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case EC_ADDR_CPU_TEMP:
> + case EC_ADDR_GPU_TEMP:
> + case EC_ADDR_MAIN_FAN_RPM_1:
> + case EC_ADDR_MAIN_FAN_RPM_2:
> + case EC_ADDR_SECOND_FAN_RPM_1:
> + case EC_ADDR_SECOND_FAN_RPM_2:
> + case EC_ADDR_BAT_ALERT:
> + case EC_ADDR_PWM_1:
> + case EC_ADDR_PWM_2:
> + case EC_ADDR_TRIGGER:
> + case EC_ADDR_SWITCH_STATUS:
> + case EC_ADDR_CHARGE_CTRL:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static const struct regmap_config uniwill_ec_config = {
> + .reg_bits = 16,
> + .val_bits = 8,
> + .writeable_reg = uniwill_writeable_reg,
> + .readable_reg = uniwill_readable_reg,
> + .volatile_reg = uniwill_volatile_reg,
> + .can_sleep = true,
> + .max_register = 0xFFF,
> + .cache_type = REGCACHE_MAPLE,
> + .use_single_read = true,
> + .use_single_write = true,
> +};
> +
> +static ssize_t fn_lock_toggle_enable_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + bool enable;
> + int ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret < 0)
> + return ret;
> +
> + if (enable)
> + value = FN_LOCK_STATUS;
> + else
> + value = 0;
> +
> + ret = regmap_update_bits(data->regmap, EC_ADDR_BIOS_OEM, FN_LOCK_STATUS, value);
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +
> +static ssize_t fn_lock_toggle_enable_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + ret = regmap_read(data->regmap, EC_ADDR_BIOS_OEM, &value);
> + if (ret < 0)
> + return ret;
> +
> + return sysfs_emit(buf, "%d\n", !!(value & FN_LOCK_STATUS));
> +}
> +
> +static DEVICE_ATTR_RW(fn_lock_toggle_enable);
> +
> +static ssize_t super_key_toggle_enable_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + bool enable;
> + int ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret < 0)
> + return ret;
> +
> + guard(mutex)(&data->super_key_lock);
> +
> + ret = regmap_read(data->regmap, EC_ADDR_SWITCH_STATUS, &value);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * We can only toggle the super key lock, so we return early if the setting
> + * is already in the correct state.
> + */
> + if (enable == !(value & SUPER_KEY_LOCK_STATUS))
> + return count;
> +
> + ret = regmap_write_bits(data->regmap, EC_ADDR_TRIGGER, TRIGGER_SUPER_KEY_LOCK,
> + TRIGGER_SUPER_KEY_LOCK);
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +
> +static ssize_t super_key_toggle_enable_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + ret = regmap_read(data->regmap, EC_ADDR_SWITCH_STATUS, &value);
> + if (ret < 0)
> + return ret;
> +
> + return sysfs_emit(buf, "%d\n", !(value & SUPER_KEY_LOCK_STATUS));
> +}
> +
> +static DEVICE_ATTR_RW(super_key_toggle_enable);
> +
> +static ssize_t touchpad_toggle_enable_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + bool enable;
> + int ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret < 0)
> + return ret;
> +
> + if (enable)
> + value = 0;
> + else
> + value = TOUCHPAD_TOGGLE_OFF;
> +
> + ret = regmap_update_bits(data->regmap, EC_ADDR_OEM_4, TOUCHPAD_TOGGLE_OFF, value);
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +
> +static ssize_t touchpad_toggle_enable_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + ret = regmap_read(data->regmap, EC_ADDR_OEM_4, &value);
> + if (ret < 0)
> + return ret;
> +
> + return sysfs_emit(buf, "%d\n", !(value & TOUCHPAD_TOGGLE_OFF));
> +}
> +
> +static DEVICE_ATTR_RW(touchpad_toggle_enable);
> +
> +static ssize_t rainbow_animation_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + bool enable;
> + int ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret < 0)
> + return ret;
> +
> + if (enable)
> + value = LIGHTBAR_WELCOME;
> + else
> + value = 0;
> +
> + guard(mutex)(&data->led_lock);
> +
> + ret = regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, LIGHTBAR_WELCOME, value);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_BAT_CTRL, LIGHTBAR_WELCOME, value);
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +
> +static ssize_t rainbow_animation_show(struct device *dev, struct device_attribute *attr, char *buf)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + ret = regmap_read(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, &value);
> + if (ret < 0)
> + return ret;
> +
> + return sysfs_emit(buf, "%d\n", !!(value & LIGHTBAR_WELCOME));
> +}
> +
> +static DEVICE_ATTR_RW(rainbow_animation);
> +
> +static ssize_t breathing_in_suspend_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + bool enable;
> + int ret;
> +
> + ret = kstrtobool(buf, &enable);
> + if (ret < 0)
> + return ret;
> +
> + if (enable)
> + value = 0;
> + else
> + value = LIGHTBAR_S3_OFF;
> +
> + /* We only access a single register here, so we do not need to use data->led_lock */
> + ret = regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, LIGHTBAR_S3_OFF, value);
> + if (ret < 0)
> + return ret;
> +
> + return count;
> +}
> +
> +static ssize_t breathing_in_suspend_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + ret = regmap_read(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, &value);
> + if (ret < 0)
> + return ret;
> +
> + return sysfs_emit(buf, "%d\n", !(value & LIGHTBAR_S3_OFF));
> +}
> +
> +static DEVICE_ATTR_RW(breathing_in_suspend);
> +
> +static struct attribute *uniwill_attrs[] = {
> + /* Keyboard-related */
> + &dev_attr_fn_lock_toggle_enable.attr,
> + &dev_attr_super_key_toggle_enable.attr,
> + &dev_attr_touchpad_toggle_enable.attr,
> + /* Lightbar-related */
> + &dev_attr_rainbow_animation.attr,
> + &dev_attr_breathing_in_suspend.attr,
> + NULL
> +};
> +
> +static umode_t uniwill_attr_is_visible(struct kobject *kobj, struct attribute *attr, int n)
> +{
> + if (attr == &dev_attr_fn_lock_toggle_enable.attr) {
> + if (supported_features & UNIWILL_FEATURE_FN_LOCK_TOGGLE)
> + return attr->mode;
> + }
> +
> + if (attr == &dev_attr_super_key_toggle_enable.attr) {
> + if (supported_features & UNIWILL_FEATURE_SUPER_KEY_TOGGLE)
> + return attr->mode;
> + }
> +
> + if (attr == &dev_attr_touchpad_toggle_enable.attr) {
> + if (supported_features & UNIWILL_FEATURE_TOUCHPAD_TOGGLE)
> + return attr->mode;
> + }
> +
> + if (attr == &dev_attr_rainbow_animation.attr ||
> + attr == &dev_attr_breathing_in_suspend.attr) {
> + if (supported_features & UNIWILL_FEATURE_LIGHTBAR)
> + return attr->mode;
> + }
> +
> + return 0;
> +}
> +
> +static const struct attribute_group uniwill_group = {
> + .is_visible = uniwill_attr_is_visible,
> + .attrs = uniwill_attrs,
> +};
> +
> +static const struct attribute_group *uniwill_groups[] = {
> + &uniwill_group,
> + NULL
> +};
> +
> +static int uniwill_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel,
> + long *val)
> +{
> + struct uniwill_data *data = dev_get_drvdata(dev);
> + unsigned int value;
> + __be16 rpm;
> + int ret;
> +
> + switch (type) {
> + case hwmon_temp:
> + switch (channel) {
> + case 0:
> + ret = regmap_read(data->regmap, EC_ADDR_CPU_TEMP, &value);
> + break;
> + case 1:
> + ret = regmap_read(data->regmap, EC_ADDR_GPU_TEMP, &value);
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + if (ret < 0)
> + return ret;
> +
> + *val = value * MILLIDEGREE_PER_DEGREE;
> + return 0;
> + case hwmon_fan:
> + switch (channel) {
> + case 0:
> + ret = regmap_bulk_read(data->regmap, EC_ADDR_MAIN_FAN_RPM_1, &rpm,
> + sizeof(rpm));
> + break;
> + case 1:
> + ret = regmap_bulk_read(data->regmap, EC_ADDR_SECOND_FAN_RPM_1, &rpm,
> + sizeof(rpm));
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + if (ret < 0)
> + return ret;
> +
> + *val = be16_to_cpu(rpm);
> + return 0;
> + case hwmon_pwm:
> + switch (channel) {
> + case 0:
> + ret = regmap_read(data->regmap, EC_ADDR_PWM_1, &value);
> + break;
> + case 1:
> + ret = regmap_read(data->regmap, EC_ADDR_PWM_2, &value);
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + if (ret < 0)
> + return ret;
> +
> + *val = fixp_linear_interpolate(0, 0, PWM_MAX, U8_MAX, value);
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static int uniwill_read_string(struct device *dev, enum hwmon_sensor_types type, u32 attr,
> + int channel, const char **str)
> +{
> + switch (type) {
> + case hwmon_temp:
> + *str = uniwill_temp_labels[channel];
> + return 0;
> + case hwmon_fan:
> + *str = uniwill_fan_labels[channel];
> + return 0;
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static const struct hwmon_ops uniwill_ops = {
> + .visible = 0444,
> + .read = uniwill_read,
> + .read_string = uniwill_read_string,
> +};
> +
> +static const struct hwmon_channel_info * const uniwill_info[] = {
> + HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ),
> + HWMON_CHANNEL_INFO(temp,
> + HWMON_T_INPUT | HWMON_T_LABEL,
> + HWMON_T_INPUT | HWMON_T_LABEL),
> + HWMON_CHANNEL_INFO(fan,
> + HWMON_F_INPUT | HWMON_F_LABEL,
> + HWMON_F_INPUT | HWMON_F_LABEL),
> + HWMON_CHANNEL_INFO(pwm,
> + HWMON_PWM_INPUT,
> + HWMON_PWM_INPUT),
> + NULL
> +};
> +
> +static const struct hwmon_chip_info uniwill_chip_info = {
> + .ops = &uniwill_ops,
> + .info = uniwill_info,
> +};
> +
> +static int uniwill_hwmon_init(struct uniwill_data *data)
> +{
> + struct device *hdev;
> +
> + if (!(supported_features & UNIWILL_FEATURE_HWMON))
> + return 0;
> +
> + hdev = devm_hwmon_device_register_with_info(data->dev, "uniwill", data,
> + &uniwill_chip_info, NULL);
> +
> + return PTR_ERR_OR_ZERO(hdev);
> +}
> +
> +static const unsigned int uniwill_led_channel_to_bat_reg[LED_CHANNELS] = {
> + EC_ADDR_LIGHTBAR_BAT_RED,
> + EC_ADDR_LIGHTBAR_BAT_GREEN,
> + EC_ADDR_LIGHTBAR_BAT_BLUE,
> +};
> +
> +static const unsigned int uniwill_led_channel_to_ac_reg[LED_CHANNELS] = {
> + EC_ADDR_LIGHTBAR_AC_RED,
> + EC_ADDR_LIGHTBAR_AC_GREEN,
> + EC_ADDR_LIGHTBAR_AC_BLUE,
> +};
> +
> +static int uniwill_led_brightness_set(struct led_classdev *led_cdev, enum led_brightness brightness)
> +{
> + struct led_classdev_mc *led_mc_cdev = lcdev_to_mccdev(led_cdev);
> + struct uniwill_data *data = container_of(led_mc_cdev, struct uniwill_data, led_mc_cdev);
> + unsigned int value;
> + int ret;
> +
> + ret = led_mc_calc_color_components(led_mc_cdev, brightness);
> + if (ret < 0)
> + return ret;
> +
> + guard(mutex)(&data->led_lock);
> +
> + for (int i = 0; i < LED_CHANNELS; i++) {
> + /* Prevent the brightness values from overflowing */
> + value = min(LED_MAX_BRIGHTNESS, data->led_mc_subled_info[i].brightness);
> + ret = regmap_write(data->regmap, uniwill_led_channel_to_ac_reg[i], value);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_write(data->regmap, uniwill_led_channel_to_bat_reg[i], value);
> + if (ret < 0)
> + return ret;
> + }
> +
> + if (brightness)
> + value = 0;
> + else
> + value = LIGHTBAR_S0_OFF;
> +
> + ret = regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, LIGHTBAR_S0_OFF, value);
> + if (ret < 0)
> + return ret;
> +
> + return regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_BAT_CTRL, LIGHTBAR_S0_OFF, value);
> +}
> +
> +#define LIGHTBAR_MASK (LIGHTBAR_APP_EXISTS | LIGHTBAR_S0_OFF | LIGHTBAR_S3_OFF | LIGHTBAR_WELCOME)
> +
> +static int uniwill_led_init(struct uniwill_data *data)
> +{
> + struct led_init_data init_data = {
> + .devicename = DRIVER_NAME,
> + .default_label = "multicolor:" LED_FUNCTION_STATUS,
> + .devname_mandatory = true,
> + };
> + unsigned int color_indices[3] = {
> + LED_COLOR_ID_RED,
> + LED_COLOR_ID_GREEN,
> + LED_COLOR_ID_BLUE,
> + };
> + unsigned int value;
> + int ret;
> +
> + if (!(supported_features & UNIWILL_FEATURE_LIGHTBAR))
> + return 0;
> +
> + ret = devm_mutex_init(data->dev, &data->led_lock);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * The EC has separate lightbar settings for AC and battery mode,
> + * so we have to ensure that both settings are the same.
> + */
> + ret = regmap_read(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, &value);
> + if (ret < 0)
> + return ret;
> +
> + value |= LIGHTBAR_APP_EXISTS;
> + ret = regmap_write(data->regmap, EC_ADDR_LIGHTBAR_AC_CTRL, value);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * The breathing animation during suspend is not supported when
> + * running on battery power.
> + */
> + value |= LIGHTBAR_S3_OFF;
> + ret = regmap_update_bits(data->regmap, EC_ADDR_LIGHTBAR_BAT_CTRL, LIGHTBAR_MASK, value);
> + if (ret < 0)
> + return ret;
> +
> + data->led_mc_cdev.led_cdev.color = LED_COLOR_ID_MULTI;
> + data->led_mc_cdev.led_cdev.max_brightness = LED_MAX_BRIGHTNESS;
> + data->led_mc_cdev.led_cdev.flags = LED_REJECT_NAME_CONFLICT;
> + data->led_mc_cdev.led_cdev.brightness_set_blocking = uniwill_led_brightness_set;
> +
> + if (value & LIGHTBAR_S0_OFF)
> + data->led_mc_cdev.led_cdev.brightness = 0;
> + else
> + data->led_mc_cdev.led_cdev.brightness = LED_MAX_BRIGHTNESS;
> +
> + for (int i = 0; i < LED_CHANNELS; i++) {
> + data->led_mc_subled_info[i].color_index = color_indices[i];
> +
> + ret = regmap_read(data->regmap, uniwill_led_channel_to_ac_reg[i], &value);
> + if (ret < 0)
> + return ret;
> +
> + /*
> + * Make sure that the initial intensity value is not greater than
> + * the maximum brightness.
> + */
> + value = min(LED_MAX_BRIGHTNESS, value);
> + ret = regmap_write(data->regmap, uniwill_led_channel_to_ac_reg[i], value);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_write(data->regmap, uniwill_led_channel_to_bat_reg[i], value);
> + if (ret < 0)
> + return ret;
> +
> + data->led_mc_subled_info[i].intensity = value;
> + data->led_mc_subled_info[i].channel = i;
> + }
> +
> + data->led_mc_cdev.subled_info = data->led_mc_subled_info;
> + data->led_mc_cdev.num_colors = LED_CHANNELS;
> +
> + return devm_led_classdev_multicolor_register_ext(data->dev, &data->led_mc_cdev,
> + &init_data);
> +}
> +
> +static int uniwill_get_property(struct power_supply *psy, const struct power_supply_ext *ext,
> + void *drvdata, enum power_supply_property psp,
> + union power_supply_propval *val)
> +{
> + struct uniwill_data *data = drvdata;
> + union power_supply_propval prop;
> + unsigned int regval;
> + int ret;
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_HEALTH:
> + ret = power_supply_get_property_direct(psy, POWER_SUPPLY_PROP_PRESENT, &prop);
> + if (ret < 0)
> + return ret;
> +
> + if (!prop.intval) {
> + val->intval = POWER_SUPPLY_HEALTH_NO_BATTERY;
> + return 0;
> + }
> +
> + ret = power_supply_get_property_direct(psy, POWER_SUPPLY_PROP_STATUS, &prop);
> + if (ret < 0)
> + return ret;
> +
> + if (prop.intval == POWER_SUPPLY_STATUS_UNKNOWN) {
> + val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
> + return 0;
> + }
> +
> + ret = regmap_read(data->regmap, EC_ADDR_BAT_ALERT, ®val);
> + if (ret < 0)
> + return ret;
> +
> + if (regval) {
> + /* Charging issue */
> + val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> + return 0;
> + }
> +
> + val->intval = POWER_SUPPLY_HEALTH_GOOD;
> + return 0;
> + case POWER_SUPPLY_PROP_CHARGE_CONTROL_END_THRESHOLD:
> + ret = regmap_read(data->regmap, EC_ADDR_CHARGE_CTRL, ®val);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = clamp_val(FIELD_GET(CHARGE_CTRL_MASK, regval), 0, 100);
Hmm, this seems to trigger an error from sparse:
CHECK drivers/platform/x86/uniwill/uniwill-acpi.c
drivers/platform/x86/uniwill/uniwill-acpi.c:1125:31: error: too long token expansion
I guess they do some crazy type validation inside those which expands
like crazy.
Based on the message and the code, it looks non-error though, just some
stupid limitation perhaps.
> + return 0;
> + default:
> + return -EINVAL;
> + }
> +}
--
i.
Powered by blists - more mailing lists