Message-ID: <20251113014116.196638-1-srinivas.pandruvada@linux.intel.com>
Date: Wed, 12 Nov 2025 17:41:14 -0800
From: Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>
To: rafael@...nel.org,
	daniel.lezcano@...aro.org
Cc: corbet@....net,
	linux-pm@...r.kernel.org,
	linux-doc@...r.kernel.org,
	linux-kernel@...r.kernel.org,
	Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>
Subject: [PATCH] Documentation: thermal: Add documentation for thermal throttle

Add documentation for Intel thermal throttling reporting events.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>
---
 Documentation/admin-guide/thermal/index.rst   |  1 +
 .../admin-guide/thermal/thermal_throttle.rst  | 84 +++++++++++++++++++
 2 files changed, 85 insertions(+)
 create mode 100644 Documentation/admin-guide/thermal/thermal_throttle.rst

diff --git a/Documentation/admin-guide/thermal/index.rst b/Documentation/admin-guide/thermal/index.rst
index 193b7b01a87d..2e0cafd19f6b 100644
--- a/Documentation/admin-guide/thermal/index.rst
+++ b/Documentation/admin-guide/thermal/index.rst
@@ -6,3 +6,4 @@ Thermal Subsystem
    :maxdepth: 1
 
    intel_powerclamp
+   thermal_throttle
diff --git a/Documentation/admin-guide/thermal/thermal_throttle.rst b/Documentation/admin-guide/thermal/thermal_throttle.rst
new file mode 100644
index 000000000000..ab146ffdffca
--- /dev/null
+++ b/Documentation/admin-guide/thermal/thermal_throttle.rst
@@ -0,0 +1,84 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
+
+=======================================
+Intel thermal throttle events reporting
+=======================================
+
+:Author: Srinivas Pandruvada <srinivas.pandruvada@...ux.intel.com>
+
+Introduction
+------------
+
+Intel processors have built in automatic and adaptive thermal monitoring mechanisms
+that force the processor to reduce its power consumption in order to operate within
+predetermined temperature limits.
+
+Refer to section "THERMAL MONITORING AND PROTECTION" in the "Intel® 64 and IA-32
+Architectures Software Developer’s Manual Volume 3 (3A, 3B, 3C, & 3D): System
+Programming Guide" for more details.
+
+In general, there are two mechanisms to control the core temperature of the processor.
+They are called "Thermal Monitor 1 (TM1) and Thermal Monitor 2 (TM2)".
+
+The status of the temperature sensor that triggers the thermal monitor (TM1/TM2) is
+indicated through the "thermal status flag" and "thermal status log flag" in the
+IA32_THERM_STATUS MSR for core level and IA32_PACKAGE_THERM_STATUS for package level.
+
+Thermal Status flag, bit 0 — When set, indicates that the processor core temperature
+is currently at the trip temperature of the thermal monitor and that the processor power
+consumption is being reduced via either TM1 or TM2, depending on which is enabled. When
+clear, the flag indicates that the core temperature is below the thermal monitor trip
+temperature. This flag is read only.
+
+Thermal Status Log flag, bit 1 — When set, indicates that the thermal sensor has tripped
+since the last power-up or reset or since the last time that software cleared this flag.
+This flag is a sticky bit; once set it remains set until cleared by software or until a
+power-up or reset of the processor. The default state is clear.
+
+It is possible that when user reads IA32_THERM_STATUS or IA32_PACKAGE_THERM_STATUS,
+TM1/TM2 is not active. In this case, "Thermal Status flag" will read "0" and the
+"Thermal Status Log flag" will be set to show any previous "TM1/TM2" activation. But
+since it needs to be cleared by software, it can't show the number of occurrences of
+"TM1/TM2" activations.
+
+Hence, Linux provides counters of how many times the "Thermal Status flag" was set. Also
+presents how long the "Thermal Status flag" was active in milliseconds. Using these counters,
+users can check if the performance was limited because of thermal events. It is recommended
+to read from sysfs instead of directly reading MSRs as the "Thermal Status Log flag" is reset
+by the driver to implement rate control.
+
+Sysfs Interface
+---------------
+
+Thermal throttling events are presented for each CPU under
+"/sys/devices/system/cpu/cpuX/thermal_throttle/", where "X" is the CPU number.
+
+All these counters are read-only. They can't be reset to 0. So, they can potentially
+overflow after reaching the maximum 64 bit unsigned integer.
+
+``core_throttle_count``
+	This shows how many times "Thermal Status flag" changed from 0 to 1
+	for this CPU. This is a 64 bit counter.
+
+``package_throttle_count``
+	This shows how many times "Thermal Status flag" changed from 0 to 1
+	for this package. Package status is broadcast to all CPUs; all CPUs in
+	the package increment this count. This is a 64-bit counter.
+
+``core_throttle_max_time_ms``
+	This shows the maximum amount of time "Thermal Status flag" was set to 1
+	for this CPU for core level flag.
+
+``package_throttle_max_time_ms``
+	This shows the maximum amount of time "Thermal Status flag" was set to 1
+	for this CPU for package level flag.
+
+``core_throttle_total_time_ms``
+	This shows the cumulative time "Thermal Status flag" was set to 1 for this
+	CPU for core level flag.
+
+``package_throttle_total_time_ms``
+	This shows the cumulative time "Thermal Status flag" was set to 1 for this
+	CPU for package level flag.
+
-- 
2.43.0

Powered by blists - more mailing lists