linux-kernel - Re: [PATCH v2 08/11] clk: qcom: dispcc: Add support for display clock controller Kaanapali

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <75e53a37-0fd2-41d6-92bc-fb4ad5856829@oss.qualcomm.com>
Date: Thu, 4 Dec 2025 12:44:16 +0530
From: Taniya Das <taniya.das@....qualcomm.com>
To: Konrad Dybcio <konrad.dybcio@....qualcomm.com>,
        Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>
Cc: Bjorn Andersson <andersson@...nel.org>,
        Michael Turquette <mturquette@...libre.com>,
        Stephen Boyd
 <sboyd@...nel.org>, Rob Herring <robh@...nel.org>,
        Krzysztof Kozlowski <krzk+dt@...nel.org>,
        Conor Dooley
 <conor+dt@...nel.org>,
        Neil Armstrong <neil.armstrong@...aro.org>,
        Maxime Coquelin <mcoquelin.stm32@...il.com>,
        Alexandre Torgue <alexandre.torgue@...s.st.com>,
        Vladimir Zapolskiy <vladimir.zapolskiy@...aro.org>,
        Konrad Dybcio <konradybcio@...nel.org>,
        Ajit Pandey <ajit.pandey@....qualcomm.com>,
        Imran Shaik <imran.shaik@....qualcomm.com>,
        Jagadeesh Kona <jagadeesh.kona@....qualcomm.com>,
        linux-arm-msm@...r.kernel.org, linux-clk@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-stm32@...md-mailman.stormreply.com,
        linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v2 08/11] clk: qcom: dispcc: Add support for display clock
 controller Kaanapali



On 12/1/2025 6:50 PM, Konrad Dybcio wrote:
> On 11/26/25 1:09 AM, Dmitry Baryshkov wrote:
>> On Tue, Nov 25, 2025 at 11:15:17PM +0530, Taniya Das wrote:
>>> Support the clock controller driver for Kaanapali to enable display SW to
>>> be able to control the clocks.
>>>
>>> Signed-off-by: Taniya Das <taniya.das@....qualcomm.com>
>>> ---
> 
> [...]
> 
>>> +/* 257.142858 MHz Configuration */
>>
>> This is a bit strange frequency for the boot config.

The lowest PLL configuration is used as boot config based on the
MDP_CLK_SRC clock requirement. The PLLs on Kaanapali can support these
lower frequencies as well.


> The frequency map lists this odd cookie as the lowest predefined config,
> perhaps it was pulled from there.
> 

Correct Konrad.

> More interestingly, the only consumer of this PLL (MDP_CLK_SRC) makes no
> effort to use the m/n/d registers, instead relying on the PLL to re-clock
> for its ratesetting with a fixed divider of 3 (and div1 @ XO rate).
> 

The m/n is not preferred in the cases where the PLL needs to slew to
derive a new VCO frequency. That is the reason to keep the divider
constant as much as possible to derive a particular frequency.

> 257.142858 * 3 = 771.428574 over-drives MDP_CLK_SRC, FWIW.
> 

The lowest frequency requirement is 85.7MHz and the frequency is derived
using
257.142858 (PLL VCO) / 3 (RCG Div) = 85.714286 MHz

there is no over-drive at RCG of MDP.

> Taniya, we've seen something like this in camera too. Is there a reason
> the frequency is being set this way?
> 

We start with the lowest frequency to configure the PLL and frequency
requirements are decided based on usecases.

-- 
Thanks,
Taniya Das