| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20251205-imx91s-frdm-v1-2-afd6cd01c299@nxp.com>
Date: Fri, 05 Dec 2025 17:03:59 +0900
From: "Yanan.Yang" <yanan.yang@....com>
To: Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>
Cc: devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
imx@...ts.linux.dev, linux-arm-kernel@...ts.infradead.org,
yanan.yang@....com, qijian.guo@....com, justin.jiang@....com,
Lei Xu <lei.xu@....com>, Xiaofeng Wei <xiaofeng.wei@....com>
Subject: [PATCH 2/2] arm64: dts: freescale: add NXP FRDM-IMX91S board
support
Add DeviceTree support for the NXP FRDM-IMX91S development board based
on the i.MX91 SoC. FRDM-IMX91S is a cost-optimized variant of FRDM-IMX91
and differs in memory, storage, Ethernet, and PMIC configuration:
- 512MB LPDDR4 (FRDM-IMX91 uses 1GB)
- 256MB FlexSPI-NAND (FRDM-IMX91 uses 8GB eMMC)
- Single GbE port (FRDM-IMX91 has dual GbE)
- PMIC PF9453 (FRDM-IMX91 uses PCA9451A)
This DT enables:
- ADC1
- UART1 and UART5
- I2C bus and children nodes
- USB and related nodes
- uSDHC1 and uSDHC2
- FlexSPI NAND flash
- Watchdog3
- Ethernet (eqos)
- FlexCAN
- MQS
Link: https://www.nxp.com/design/design-center/development-boards-and-designs/FRDM-IMX91S
(FRDM-IMX91S board page)
Link: https://www.nxp.com/design/design-center/development-boards-and-designs/FRDM-IMX91
(FRDM-IMX91 board page)
Co-developed-by: Lei Xu <lei.xu@....com>
Signed-off-by: Lei Xu <lei.xu@....com>
Co-developed-by: Xiaofeng Wei <xiaofeng.wei@....com>
Signed-off-by: Xiaofeng Wei <xiaofeng.wei@....com>
Signed-off-by: Yanan.Yang <yanan.yang@....com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/imx91-11x11-frdm-s.dts | 692 +++++++++++++++++++++
2 files changed, 693 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index f30d3fd724d0..927bf76a05f3 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -368,6 +368,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-tqma8xqps-mb-smarc-2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8ulp-9x9-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx91-11x11-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx91-11x11-frdm-s.dtb
dtb-$(CONFIG_ARCH_MXC) += imx91-phyboard-segin.dtb
dtb-$(CONFIG_ARCH_MXC) += imx91-tqma9131-mba91xxca.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-9x9-qsb.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx91-11x11-frdm-s.dts b/arch/arm64/boot/dts/freescale/imx91-11x11-frdm-s.dts
new file mode 100644
index 000000000000..0952a685c3f5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx91-11x11-frdm-s.dts
@@ -0,0 +1,692 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2025 NXP
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/usb/pd.h>
+#include "imx91.dtsi"
+
+/ {
+ compatible = "fsl,imx91-11x11-frdm-s", "fsl,imx91";
+ model = "NXP FRDM-IMX91S board";
+
+ aliases {
+ ethernet0 = &fec;
+ ethernet1 = &eqos;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ i2c0 = &lpi2c1;
+ i2c1 = &lpi2c2;
+ i2c2 = &lpi2c3;
+ i2c3 = &lpi2c4;
+ i2c4 = &lpi2c5;
+ i2c5 = &lpi2c6;
+ i2c6 = &lpi2c7;
+ i2c7 = &lpi2c8;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ rtc0 = &bbnsm_rtc;
+ serial0 = &lpuart1;
+ serial1 = &lpuart2;
+ serial2 = &lpuart3;
+ serial3 = &lpuart4;
+ serial4 = &lpuart5;
+ serial5 = &lpuart6;
+ serial6 = &lpuart7;
+ serial7 = &lpuart8;
+ };
+
+ chosen {
+ stdout-path = &lpuart1;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pinctrl_gpio_key>;
+ pinctrl-names = "default";
+
+ button {
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+ gpios = <&gpio3 26 GPIO_PULL_UP>;
+ label = "User Button";
+ linux,code = <BTN_1>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ status {
+ default-state = "on";
+ gpios = <&pcal6524 7 GPIO_ACTIVE_LOW>;
+ label = "green:status";
+ };
+ };
+
+ reg_vref_1v8: regulator-adc-vref {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "vref_1v8";
+ };
+
+ reg_can_stby: regulator-can-stby {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "can-stby";
+ gpio = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_usdhc1_vmmc: regulator-usdhc1 {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "WLAN_EN";
+ startup-delay-us = <20000>;
+ gpio = <&pcal6524 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ off-on-delay-us = <12000>;
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ pinctrl-names = "default";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "VSD_3V3";
+ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_vbus: regulator-vbus {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "USB_VBUS";
+ gpio = <&pcal6524 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reserved-memory {
+ ranges;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ alloc-ranges = <0 0x80000000 0 0x20000000>;
+ reusable;
+ size = <0 0x2000000>;
+ linux,cma-default;
+ };
+ };
+
+ sound-mqs {
+ compatible = "fsl,imx6sx-sdb-mqs", "fsl,imx-audio-mqs";
+ audio-codec = <&mqs1>;
+ audio-cpu = <&sai1>;
+ model = "mqs-audio";
+ };
+
+ usdhc1_pwrseq: usdhc1_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pcal6524 18 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&adc1 {
+ vref-supply = <®_vref_1v8>;
+ status = "okay";
+};
+
+&eqos {
+ phy-handle = <ðphy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-0 = <&pinctrl_eqos>;
+ pinctrl-1 = <&pinctrl_eqos_sleep>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <5000000>;
+
+ ethphy1: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+ };
+};
+
+&flexcan1 {
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ pinctrl-1 = <&pinctrl_flexcan1_sleep>;
+ pinctrl-names = "default", "sleep";
+ xceiver-supply = <®_can_stby>;
+ status = "okay";
+};
+
+&flexspi1 {
+ pinctrl-0 = <&pinctrl_flexspi1>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <104000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ reg = <0x000000 0x800000>;
+ label = "bootloader";
+ };
+
+ partition@1 {
+ reg = <0x800000 0x800000>;
+ label = "env";
+ };
+
+ partition@2 {
+ reg = <0x1000000 0x2800000>;
+ label = "kernel";
+ };
+
+ partition@3 {
+ reg = <0x3800000 0x20000>;
+ label = "dtb";
+ };
+
+ partition@4 {
+ reg = <0x3820000 0xFFFFFFFF>;
+ label = "rootfs";
+ linux,rootfs;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_eqos: eqosgrp {
+ fsl,pins = <
+ MX91_PAD_ENET1_MDC__ENET1_MDC 0x57e
+ MX91_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x57e
+ MX91_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e
+ MX91_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e
+ MX91_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e
+ MX91_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e
+ MX91_PAD_ENET1_RXC__ENET_QOS_RGMII_RXC 0x5fe
+ MX91_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e
+ MX91_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x57e
+ MX91_PAD_ENET1_TD1__ENET1_RGMII_TD1 0x57e
+ MX91_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x57e
+ MX91_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x57e
+ MX91_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x5fe
+ MX91_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x57e
+ >;
+ };
+
+ pinctrl_eqos_sleep: eqossleepgrp {
+ fsl,pins = <
+ MX91_PAD_ENET1_MDC__GPIO4_IO0 0x31e
+ MX91_PAD_ENET1_MDIO__GPIO4_IO1 0x31e
+ MX91_PAD_ENET1_RD0__GPIO4_IO10 0x31e
+ MX91_PAD_ENET1_RD1__GPIO4_IO11 0x31e
+ MX91_PAD_ENET1_RD2__GPIO4_IO12 0x31e
+ MX91_PAD_ENET1_RD3__GPIO4_IO13 0x31e
+ MX91_PAD_ENET1_RXC__GPIO4_IO9 0x31e
+ MX91_PAD_ENET1_RX_CTL__GPIO4_IO8 0x31e
+ MX91_PAD_ENET1_TD0__GPIO4_IO5 0x31e
+ MX91_PAD_ENET1_TD1__GPIO4_IO4 0x31e
+ MX91_PAD_ENET1_TD2__GPIO4_IO3 0x31e
+ MX91_PAD_ENET1_TD3__GPIO4_IO2 0x31e
+ MX91_PAD_ENET1_TXC__GPIO4_IO7 0x31e
+ MX91_PAD_ENET1_TX_CTL__GPIO4_IO6 0x31e
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX91_PAD_GPIO_IO28__CAN1_TX 0x139e
+ MX91_PAD_GPIO_IO29__CAN1_RX 0x139e
+ MX91_PAD_PDM_BIT_STREAM1__GPIO1_IO10 0x31e
+ >;
+ };
+
+ pinctrl_flexcan1_sleep: flexcan1sleepgrp {
+ fsl,pins = <
+ MX91_PAD_GPIO_IO28__GPIO2_IO28 0x31e
+ MX91_PAD_GPIO_IO29__GPIO2_IO29 0x31e
+ MX91_PAD_PDM_BIT_STREAM1__GPIO1_IO10 0x31e
+ >;
+ };
+
+ pinctrl_flexspi1: flexspi1grp {
+ fsl,pins = <
+ MX91_PAD_SD3_CLK__FLEXSPI1_A_SCLK 0x3fe
+ MX91_PAD_SD3_CMD__FLEXSPI1_A_SS0_B 0x3fe
+ MX91_PAD_SD3_DATA0__FLEXSPI1_A_DATA0 0x3fe
+ MX91_PAD_SD3_DATA1__FLEXSPI1_A_DATA1 0x3fe
+ MX91_PAD_SD3_DATA2__FLEXSPI1_A_DATA2 0x3fe
+ MX91_PAD_SD3_DATA3__FLEXSPI1_A_DATA3 0x3fe
+ >;
+ };
+
+ pinctrl_gpio_key: gpiokeysgrp {
+ fsl,pins = <
+ MX91_PAD_CCM_CLKO1__GPIO3_IO26 0x0000031E
+ >;
+ };
+
+ pinctrl_lpi2c1: lpi2c1grp {
+ fsl,pins = <
+ MX91_PAD_I2C1_SCL__LPI2C1_SCL 0x40000b9e
+ MX91_PAD_I2C1_SDA__LPI2C1_SDA 0x40000b9e
+ >;
+ };
+
+ pinctrl_lpi2c2: lpi2c2grp {
+ fsl,pins = <
+ MX91_PAD_I2C2_SCL__LPI2C2_SCL 0x40000b9e
+ MX91_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e
+ >;
+ };
+
+ pinctrl_mqs1: mqs1grp {
+ fsl,pins = <
+ MX91_PAD_PDM_CLK__MQS1_LEFT 0x31e
+ MX91_PAD_PDM_BIT_STREAM0__MQS1_RIGHT 0x31e
+ >;
+ };
+
+ pinctrl_pcal6524: pcal6524grp {
+ fsl,pins = <
+ MX91_PAD_CCM_CLKO2__GPIO3_IO27 0x31e
+ MX91_PAD_SD1_DATA5__GPIO3_IO15 0x31e
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <
+ MX91_PAD_SD2_RESET_B__GPIO3_IO7 0x31e
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX91_PAD_UART1_RXD__LPUART1_RX 0x31e
+ MX91_PAD_UART1_TXD__LPUART1_TX 0x31e
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX91_PAD_DAP_TDO_TRACESWO__LPUART5_TX 0x31e
+ MX91_PAD_DAP_TDI__LPUART5_RX 0x31e
+ MX91_PAD_DAP_TMS_SWDIO__LPUART5_RTS_B 0x31e
+ MX91_PAD_DAP_TCLK_SWCLK__LPUART5_CTS_B 0x31e
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX91_PAD_SD1_CLK__USDHC1_CLK 0x1582
+ MX91_PAD_SD1_CMD__USDHC1_CMD 0x1382
+ MX91_PAD_SD1_DATA0__USDHC1_DATA0 0x1382
+ MX91_PAD_SD1_DATA1__USDHC1_DATA1 0x1382
+ MX91_PAD_SD1_DATA2__USDHC1_DATA2 0x1382
+ MX91_PAD_SD1_DATA3__USDHC1_DATA3 0x1382
+ MX91_PAD_SD1_DATA4__GPIO3_IO14 0x031E
+ MX91_PAD_SD1_STROBE__GPIO3_IO18 0x031E
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX91_PAD_SD1_CLK__USDHC1_CLK 0x158e
+ MX91_PAD_SD1_CMD__USDHC1_CMD 0x138e
+ MX91_PAD_SD1_DATA0__USDHC1_DATA0 0x138e
+ MX91_PAD_SD1_DATA1__USDHC1_DATA1 0x138e
+ MX91_PAD_SD1_DATA2__USDHC1_DATA2 0x138e
+ MX91_PAD_SD1_DATA3__USDHC1_DATA3 0x138e
+ MX91_PAD_SD1_DATA4__GPIO3_IO14 0x031E
+ MX91_PAD_SD1_STROBE__GPIO3_IO18 0x031E
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX91_PAD_SD1_CLK__USDHC1_CLK 0x15fe
+ MX91_PAD_SD1_CMD__USDHC1_CMD 0x13fe
+ MX91_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe
+ MX91_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe
+ MX91_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe
+ MX91_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe
+ MX91_PAD_SD1_DATA4__GPIO3_IO14 0x031E
+ MX91_PAD_SD1_STROBE__GPIO3_IO18 0x031E
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX91_PAD_SD2_CD_B__GPIO3_IO0 0x31e
+ >;
+ };
+
+ pinctrl_usdhc2_gpio_sleep: usdhc2gpiosleepgrp {
+ fsl,pins = <
+ MX91_PAD_SD2_CD_B__GPIO3_IO0 0x51e
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX91_PAD_SD2_CLK__USDHC2_CLK 0x1582
+ MX91_PAD_SD2_CMD__USDHC2_CMD 0x1382
+ MX91_PAD_SD2_DATA0__USDHC2_DATA0 0x1382
+ MX91_PAD_SD2_DATA1__USDHC2_DATA1 0x1382
+ MX91_PAD_SD2_DATA2__USDHC2_DATA2 0x1382
+ MX91_PAD_SD2_DATA3__USDHC2_DATA3 0x1382
+ MX91_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
+ >;
+ };
+
+ pinctrl_usdhc2_sleep: usdhc2sleepgrp {
+ fsl,pins = <
+ MX91_PAD_SD2_CLK__GPIO3_IO1 0x51e
+ MX91_PAD_SD2_CMD__GPIO3_IO2 0x51e
+ MX91_PAD_SD2_DATA0__GPIO3_IO3 0x51e
+ MX91_PAD_SD2_DATA1__GPIO3_IO4 0x51e
+ MX91_PAD_SD2_DATA2__GPIO3_IO5 0x51e
+ MX91_PAD_SD2_DATA3__GPIO3_IO6 0x51e
+ MX91_PAD_SD2_VSELECT__GPIO3_IO19 0x51e
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX91_PAD_SD2_CLK__USDHC2_CLK 0x158e
+ MX91_PAD_SD2_CMD__USDHC2_CMD 0x138e
+ MX91_PAD_SD2_DATA0__USDHC2_DATA0 0x138e
+ MX91_PAD_SD2_DATA1__USDHC2_DATA1 0x138e
+ MX91_PAD_SD2_DATA2__USDHC2_DATA2 0x138e
+ MX91_PAD_SD2_DATA3__USDHC2_DATA3 0x138e
+ MX91_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX91_PAD_SD2_CLK__USDHC2_CLK 0x15fe
+ MX91_PAD_SD2_CMD__USDHC2_CMD 0x13fe
+ MX91_PAD_SD2_DATA0__USDHC2_DATA0 0x13fe
+ MX91_PAD_SD2_DATA1__USDHC2_DATA1 0x13fe
+ MX91_PAD_SD2_DATA2__USDHC2_DATA2 0x13fe
+ MX91_PAD_SD2_DATA3__USDHC2_DATA3 0x13fe
+ MX91_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX91_PAD_WDOG_ANY__WDOG1_WDOG_ANY 0x31e
+ >;
+ };
+};
+
+&lpi2c1 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&pinctrl_lpi2c1>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ pcf2131: rtc@53 {
+ compatible = "nxp,pcf2131";
+ reg = <0x53>;
+ interrupt-parent = <&pcal6524>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&lpi2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ pinctrl-0 = <&pinctrl_lpi2c2>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ pcal6524: gpio@22 {
+ compatible = "nxp,pcal6524";
+ reg = <0x22>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupt-parent = <&gpio3>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ pinctrl-0 = <&pinctrl_pcal6524>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+ };
+
+ pmic@32 {
+ compatible = "nxp,pf9453";
+ reg = <0x32>;
+ interrupt-parent = <&pcal6524>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+
+ regulators {
+ buck1: BUCK1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3775000>;
+ regulator-min-microvolt = <600000>;
+ regulator-name = "BUCK1";
+ };
+
+ buck2: BUCK2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <2187500>;
+ regulator-min-microvolt = <600000>;
+ regulator-name = "BUCK2";
+ regulator-ramp-delay = <12500>;
+ };
+
+ buck3: BUCK3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3775000>;
+ regulator-min-microvolt = <600000>;
+ regulator-name = "BUCK3";
+ };
+
+ buck4: BUCK4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3775000>;
+ regulator-min-microvolt = <600000>;
+ regulator-name = "BUCK4";
+ };
+
+ ldo1: LDO1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <800000>;
+ regulator-name = "LDO1";
+ };
+
+ ldo2: LDO2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1950000>;
+ regulator-min-microvolt = <500000>;
+ regulator-name = "LDO2";
+ };
+
+ ldo_snvs: LDO-SNVS {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3400000>;
+ regulator-min-microvolt = <1200000>;
+ regulator-name = "LDO-SNVS";
+ };
+ };
+ };
+
+ ptn5110: tcpc@52 {
+ compatible = "nxp,ptn5110", "tcpci";
+ reg = <0x52>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+
+ typec1_con: connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USB-C";
+ op-sink-microwatt = <15000000>;
+ power-role = "dual";
+ self-powered;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 20000, 3000)>;
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ typec1_dr_sw: endpoint {
+ remote-endpoint = <&usb1_drd_sw>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&lpuart1 {
+ pinctrl-0 = <&pinctrl_uart1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&lpuart5 {
+ pinctrl-0 = <&pinctrl_uart5>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ bluetooth {
+ compatible = "nxp,88w8987-bt";
+ };
+};
+
+&media_blk_ctrl {
+ status = "okay";
+};
+
+&mqs1 {
+ clocks = <&clk IMX93_CLK_MQS1_GATE>;
+ clock-names = "mclk";
+ pinctrl-0 = <&pinctrl_mqs1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&sai1 {
+ clocks = <&clk IMX93_CLK_SAI1_IPG>, <&clk IMX93_CLK_DUMMY>,
+ <&clk IMX93_CLK_SAI1_GATE>, <&clk IMX93_CLK_DUMMY>,
+ <&clk IMX93_CLK_DUMMY>, <&clk IMX93_CLK_AUDIO_PLL>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k";
+ assigned-clocks = <&clk IMX93_CLK_SAI1>;
+ assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>;
+ assigned-clock-rates = <24576000>;
+ #sound-dai-cells = <0>;
+ fsl,sai-mclk-direction-output;
+ status = "okay";
+};
+
+&usbotg1 {
+ adp-disable;
+ disable-over-current;
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ usb-role-switch;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ samsung,picophy-pre-emp-curr-control = <3>;
+ status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&typec1_dr_sw>;
+ };
+ };
+};
+
+&usbotg2 {
+ disable-over-current;
+ dr_mode = "host";
+ vbus-supply = <®_usb_vbus>;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ samsung,picophy-pre-emp-curr-control = <3>;
+ status = "okay";
+};
+
+&usdhc1 {
+ bus-width = <8>;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&usdhc1_pwrseq>;
+ non-removable;
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ vmmc-supply = <®_usdhc1_vmmc>;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc2 {
+ bus-width = <4>;
+ cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
+ no-mmc;
+ no-sdio;
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_gpio_sleep>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&wdog3 {
+ pinctrl-0 = <&pinctrl_wdog>;
+ pinctrl-names = "default";
+ fsl,ext-reset-output;
+ status = "okay";
+};
--
2.43.0
Powered by blists - more mailing lists