linux-kernel - Re: [PATCH v2 0/3] arm64: boot: dts: ti: k3-am62l: allow WKUP UART wakeup from LPM

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <c7dfe4a3-1bf5-4e50-b4b7-8752aa9ef1f5@ti.com>
Date: Wed, 7 Jan 2026 15:44:54 -0600
From: Kendall Willis <k-willis@...com>
To: Bryan Brattlof <bb@...com>
CC: Nishanth Menon <nm@...com>, Vignesh Raghavendra <vigneshr@...com>, "Tero
 Kristo" <kristo@...nel.org>, Rob Herring <robh@...nel.org>, "Krzysztof
 Kozlowski" <krzk+dt@...nel.org>, Conor Dooley <conor+dt@...nel.org>, "Dhruva
 Gole" <d-gole@...com>, <vishalm@...com>, <sebin.francis@...com>,
	<msp@...libre.com>, <khilman@...libre.com>, <a-kaur@...com>,
	<s-kochidanadu@...com>, <linux-arm-kernel@...ts.infradead.org>,
	<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2 0/3] arm64: boot: dts: ti: k3-am62l: allow WKUP UART
 wakeup from LPM

On 1/7/26 10:45, Bryan Brattlof wrote:
> On January  6, 2026 thus sayeth Kendall Willis:
>> K3 TI AM62L SoC supports wakeup from WKUP UART when the SoC is in the
>> DeepSleep low power mode. To allow wakeup from WKUP UART the target-module
>> device tree node is enabled. The ti-sysc interconnect target module driver
>> is used to configure the the SYSCONFIG related registers. In this case,
>> the interconnect target module node configures the WKUP UART to be able to
>> wakeup from system suspend. The SYSC register is used to enable wakeup
>> from system suspend for the WKUP UART. Refer to 14.7.2.5 UART in the
>> AM62L Techincal Reference Manual for registers referenced [1].
>>
>> Previous TI SoCs configure the WKUP UART to wakeup from system suspend
>> using the ti-sysc interconnect target module driver. Refer to commit
>> ce27f7f9e328 ("arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for
>> wkup_uart0") for an example of this.
> 
> I think I may be confused. What is setting the pinmux for the wkup_uart
> to allow us to trigger the wake event? It looks like they reset to GPIO
> pins if not set. Is firmware doing this?

On AM62L, the WKUP UART pinmux is initially set by TFA so that it is set 
to the UART pins, not GPIO. The target-module node sets the WKUP UART 
SYSC register so that wakeup is enabled.

Best,
Kendall

> 
> ~Bryan