| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20260109104504.3147745-4-ziyue.zhang@oss.qualcomm.com>
Date: Fri, 9 Jan 2026 18:45:04 +0800
From: Ziyue Zhang <ziyue.zhang@....qualcomm.com>
To: andersson@...nel.org, konradybcio@...nel.org, robh@...nel.org,
krzk+dt@...nel.org, conor+dt@...nel.org, ziyue.zhang@....qualcomm.com,
jingoohan1@...il.com, mani@...nel.org, lpieralisi@...nel.org,
kwilczynski@...nel.org, bhelgaas@...gle.com, johan+linaro@...nel.org,
vkoul@...nel.org, kishon@...nel.org, neil.armstrong@...aro.org,
abel.vesa@...aro.org, kw@...ux.com
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-pci@...r.kernel.org,
linux-phy@...ts.infradead.org, qiang.yu@....qualcomm.com,
quic_krichai@...cinc.com, quic_vbadigan@...cinc.com,
Krishna Chaitanya Chundru <krishna.chundru@....qualcomm.com>,
Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>
Subject: [PATCH v4 3/3] arm64: dts: qcom: Add PCIe3 and PCIe5 regulators for HAMAO-IOT-EVK board
HAMAO IoT EVK uses PCIe5 to connect an SDX65 module for WWAN functionality
and PCIe3 to connect a SATA controller. These interfaces require multiple
voltage rails: PCIe5 needs 3.3V supplied by vreg_wwan, while PCIe3 requires
12V, 3.3V, and 3.3V AUX rails, controlled via PMIC GPIOs.
Add the required fixed regulators with related pin configuration, and
connect them to the PCIe3 and PCIe5 ports to ensure proper power for the
SDX65 module and SATA controller.
Move reset and wake GPIO properties from RC nodes to port nodes.
Signed-off-by: Ziyue Zhang <ziyue.zhang@....qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@....qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>
---
arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 97 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 6 --
2 files changed, 97 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 898b92627f84..07378ee183f9 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -253,6 +253,48 @@ vreg_nvme: regulator-nvme {
regulator-boot-on;
};
+ vreg_pcie_12v: regulator-pcie-12v {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+
+ gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&pcie_x8_12v>;
+ pinctrl-names = "default";
+ };
+
+ vreg_pcie_3v3: regulator-pcie-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&pm_sde7_main_3p3_en>;
+ pinctrl-names = "default";
+ };
+
+ vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_3P3_AUX";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&pm_sde7_aux_3p3_en>;
+ pinctrl-names = "default";
+ };
+
/* Left unused as the retimer is not used on this board. */
vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
compatible = "regulator-fixed";
@@ -920,7 +962,19 @@ &mdss_dp3_phy {
status = "okay";
};
+&pcie3_port0 {
+ vpcie12v-supply = <&vreg_pcie_12v>;
+ vpcie3v3-supply = <&vreg_pcie_3v3>;
+ vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+
+ reset-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+};
+
&pcie4_port0 {
+ reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
wifi@0 {
compatible = "pci17cb,1107";
reg = <0x10000 0x0 0x0 0x0 0x0>;
@@ -937,10 +991,24 @@ wifi@0 {
};
};
+&pcie5 {
+ vddpe-3v3-supply = <&vreg_wwan>;
+};
+
+&pcie5_port0 {
+ reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
+};
+
&pcie6a {
vddpe-3v3-supply = <&vreg_nvme>;
};
+&pcie6a_port0 {
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+};
+
&pm8550_gpios {
rtmr0_default: rtmr0-reset-n-active-state {
pins = "gpio10";
@@ -961,6 +1029,17 @@ usb0_3p3_reg_en: usb0-3p3-reg-en-state {
};
};
+&pm8550ve_8_gpios {
+ pcie_x8_12v: pcie-12v-default-state {
+ pins = "gpio8";
+ function = "normal";
+ output-enable;
+ output-high;
+ bias-pull-down;
+ power-source = <0>;
+ };
+};
+
&pm8550ve_9_gpios {
usb0_1p8_reg_en: usb0-1p8-reg-en-state {
pins = "gpio8";
@@ -1025,6 +1104,24 @@ edp_bl_reg_en: edp-bl-reg-en-state {
};
};
+&pmc8380_3_gpios {
+ pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
+ pins = "gpio8";
+ function = "normal";
+ output-enable;
+ bias-pull-down;
+ power-source = <0>;
+ };
+
+ pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
+ pins = "gpio6";
+ function = "normal";
+ output-enable;
+ bias-pull-down;
+ power-source = <0>;
+ };
+};
+
&pmc8380_5_gpios {
usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
pins = "gpio8";
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
index 81866f94fe01..b8e3e04a6fbd 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
@@ -405,9 +405,6 @@ &pcie3_phy {
};
&pcie4 {
- perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
-
pinctrl-0 = <&pcie4_default>;
pinctrl-names = "default";
@@ -436,9 +433,6 @@ &pcie5_phy {
};
&pcie6a {
- perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
- wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
-
pinctrl-0 = <&pcie6a_default>;
pinctrl-names = "default";
--
2.34.1
Powered by blists - more mailing lists