linux-kernel - [PATCH v7 0/2] net: mhi: Add support to enable ethernet interface

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20260205-eth_vdev_next-20260204_eth-v7-0-f85645210f81@qti.qualcomm.com>
Date: Thu, 05 Feb 2026 16:04:39 +0530
From: Vivek Pernamitta <vivek.pernamitta@....qualcomm.com>
To: Andrew Lunn <andrew+netdev@...n.ch>,
        "David S. Miller" <davem@...emloft.net>,
        Eric Dumazet <edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>,
        Paolo Abeni <pabeni@...hat.com>,
        Manivannan Sadhasivam <mani@...nel.org>
Cc: netdev@...r.kernel.org, linux-kernel@...r.kernel.org, mhi@...ts.linux.dev,
        linux-arm-msm@...r.kernel.org,
        Vivek Pernamitta <vpernami@....qualcomm.com>,
        Vivek Pernamitta <vivek.pernamitta@....qualcomm.com>
Subject: [PATCH v7 0/2] net: mhi: Add support to enable ethernet interface

Add support to configure a new client as Ethernet type over MHI
by setting "mhi_device_info.ethernet_if = true". Create a new
Ethernet interface named eth%d. This complements existing NET
driver support.

Introduce IP_SW1, ETH0, and ETH1 network interfaces required
for M-plane, NETCONF, and S-plane components.

M-plane:
Implement DU M-Plane software for non-real-time O-RAN
management between O-DU and O-RU using NETCONF/YANG and
O-RAN WG4 M-Plane YANG models. Provide capability exchange,
configuration management, performance monitoring, and fault
management per O-RAN.WG4.TS.MP.0-R004-v18.00.

YANG model based interface aligned with O-RAN WG4 M-Plane
specifications over TCP between the OAM application on the
host and the DU M-Plane software running on the X100 platform.

Netconf:
Use NETCONF protocol for configuration operations such as
fetching, modifying, and deleting network device
configurations.

This interface is used for IETF Netconf communication,
enabling a Netconf server on the ORU to interact with a
Netconf client running on the host.

S-plane:
Support frequency and time synchronization between O-DUs and
O-RUs using Synchronous Ethernet and IEEE 1588. Assume PTP
transport over L2 Ethernet (ITU-T G.8275.1) for full timing
support; allow PTP over UDP/IP (ITU-T G.8275.2) with reduced
reliability, as per ORAN spec O-RAN.WG4.CUS.0-R003-v12.00.

To support accurate phase and time synchronization between
the host (L2) and device (L1-High), the system must exchange
PTP messages as raw Layer-2 Ethernet frames, because the
ITU-T G.8275.1 profile operates strictly over Ethernet
multicast and not over IP networks. This means the device’s
PTP stack can only send and receive PTP Announce, Sync,
Follow-Up, and Delay messages in native Ethernet format, not
as IPv4/IPv6 packets. However, the host and device communicate
only through MHI/PCIe, which provides no native Ethernet
interface. Therefore, the system must implement a virtual
Ethernet interface over MHI on both sides. This virtual
Layer-2 link enables true Ethernet-frame transport, ensuring
the device’s PTP implementation remains fully compliant with
the G.8275.1 Ethernet-based timing model.

The actual link between the device (QDU100) and the host is
PCIe/MHI. The device has the Ethernet interface and is exposed
as the MHI channel to the host. So this patch creates the
Ethernet interface on the host based on the 'IP_ETH' channel
so that the host can use this interface for exchanging the
NETCONF packets.

The patch primarily addresses host-to-DU(QDU100) communication.
However, the NETCONF/M-Plane packets originating from the host
will eventually be transmitted from the DU to the RU over the
fronthaul, which uses Ethernet. For additional details on this
architecture and data flow, refer to the O-RAN Management
Plane Specification:

O-RAN.WG4.MP.0-v07.00
O-RAN Alliance Working Group 4 – Management Plane
Specification
Chapter 4: O-RU to O-DU Interface Management

Signed-off-by: Vivek Pernamitta <vpernami@....qualcomm.com>
---
patchset link for V6 : https://lore.kernel.org/all/20251209-vdev_next-20251208_eth_v6-v6-0-80898204f5d8@quicinc.com/
patchset link for V1 (first post) : https://lore.kernel.org/all/20250724-b4-eth_us-v1-0-4dff04a9a128@quicinc.com/

changes to v7:
- Updated to NET_NAME_ENUM while allocating netdev as per Andrew
- Updated more information as per comments from Jakub and Mani

changes to v6:
- Removed interm variable useage as per comments from Simon and Dmirty.
- Squashed gerrits 1 and 2 in single gerrit.
- Added more description for M-plane, Netconf and S-plane.

changes to v5:
- change in email ID from "quic_vpernami@...cinc.com" to "vivek.pernamitta@....qualcomm.com"
- Renamed to patch v5 as per comments from Manivannan
- Restored to original name as per comments from Jakub
- Renamed the ethernet interfce to eth%d as per Jakub
---

---
Vivek Pernamitta (2):
      net: mhi: Enable Ethernet interface support
      bus: mhi: host: pci: Enable IP_SW1, IP_ETH0 and IP_ETH1 channels for QDU100

 drivers/bus/mhi/host/pci_generic.c |  8 ++++
 drivers/net/mhi_net.c              | 75 +++++++++++++++++++++++++++++++-------
 2 files changed, 70 insertions(+), 13 deletions(-)
---
base-commit: 0f8a890c4524d6e4013ff225e70de2aed7e6d726
change-id: 20260205-eth_vdev_next-20260204_eth-807136ad5cd0

Best regards,
-- 
Vivek Pernamitta <vpernami@....qualcomm.com>