Adds basic magic packet wake on lan support to the sky2 driver. Note: initial WOL value is based on BIOS settings. Signed-off-by: Stephen Hemminger --- drivers/net/sky2.c | 208 ++++++++++++++++++++++++++++++++++++++++++++++------- drivers/net/sky2.h | 28 ++----- 2 files changed, 189 insertions(+), 47 deletions(-) --- sky2-2.6.orig/drivers/net/sky2.c 2007-01-26 11:26:52.000000000 -0800 +++ sky2-2.6/drivers/net/sky2.c 2007-01-26 11:27:29.000000000 -0800 @@ -567,6 +567,73 @@ spin_unlock_bh(&sky2->phy_lock); } +/* Put device in state to listen for Wake On Lan */ +static void sky2_wol_init(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + enum flow_control save_mode; + u16 ctrl; + u32 reg1; + + /* Bring hardware out of reset */ + sky2_write16(hw, B0_CTST, CS_RST_CLR); + sky2_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR); + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + /* Force to 10/100 + * sky2_reset will re-enable on resume + */ + save_mode = sky2->flow_mode; + ctrl = sky2->advertising; + + sky2->advertising &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full); + sky2->flow_mode = FC_NONE; + sky2_phy_power(hw, port, 1); + sky2_phy_reinit(sky2); + + sky2->flow_mode = save_mode; + sky2->advertising = ctrl; + + /* Set GMAC to no flow control and auto update for speed/duplex */ + gma_write16(hw, port, GM_GP_CTRL, + GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA| + GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS); + + /* Set WOL address */ + memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR), + sky2->netdev->dev_addr, ETH_ALEN); + + /* Turn on appropriate WOL control bits */ + sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT); + ctrl = 0; + if (sky2->wol & WAKE_PHY) + ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT; + + if (sky2->wol & WAKE_MAGIC) + ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;; + + ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; + sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); + + /* Turn on legacy PCI-Express PME mode */ + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 |= PCI_Y2_PME_LEGACY; + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + /* block receiver */ + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); + +} + static void sky2_mac_init(struct sky2_hw *hw, unsigned port) { struct sky2_port *sky2 = netdev_priv(hw->dev[port]); @@ -2399,11 +2466,9 @@ } -static int sky2_reset(struct sky2_hw *hw) +static int __devinit sky2_init(struct sky2_hw *hw) { - u16 status; u8 t8; - int i; sky2_write8(hw, B0_CTST, CS_RST_CLR); @@ -2424,6 +2489,22 @@ return -EOPNOTSUPP; } + hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); + hw->ports = 1; + t8 = sky2_read8(hw, B2_Y2_HW_RES); + if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { + if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC)) + ++hw->ports; + } + + return 0; +} + +static void sky2_reset(struct sky2_hw *hw) +{ + u16 status; + int i; + /* disable ASF */ if (hw->chip_id <= CHIP_ID_YUKON_EC) { sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); @@ -2448,14 +2529,6 @@ sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL); - hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); - hw->ports = 1; - t8 = sky2_read8(hw, B2_Y2_HW_RES); - if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { - if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC)) - ++hw->ports; - } - sky2_power_on(hw); for (i = 0; i < hw->ports; i++) { @@ -2539,7 +2612,37 @@ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); +} +static inline u8 sky2_wol_supported(const struct sky2_hw *hw) +{ + return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0; +} + +static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + const struct sky2_port *sky2 = netdev_priv(dev); + + wol->supported = sky2_wol_supported(sky2->hw); + wol->wolopts = sky2->wol; +} + +static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + if (wol->wolopts & ~sky2_wol_supported(sky2->hw)) + return -EOPNOTSUPP; + + sky2->wol = wol->wolopts; + + if (hw->chip_id == CHIP_ID_YUKON_EC_U) + sky2_write32(hw, B0_CTST, sky2->wol + ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF); + + if (!netif_running(dev)) + sky2_wol_init(sky2); return 0; } @@ -3167,7 +3270,9 @@ static const struct ethtool_ops sky2_ethtool_ops = { .get_settings = sky2_get_settings, .set_settings = sky2_set_settings, - .get_drvinfo = sky2_get_drvinfo, + .get_drvinfo = sky2_get_drvinfo, + .get_wol = sky2_get_wol, + .set_wol = sky2_set_wol, .get_msglevel = sky2_get_msglevel, .set_msglevel = sky2_set_msglevel, .nway_reset = sky2_nway_reset, @@ -3197,7 +3302,8 @@ /* Initialize network device */ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, - unsigned port, int highmem) + unsigned port, + int highmem, int wol) { struct sky2_port *sky2; struct net_device *dev = alloc_etherdev(sizeof(*sky2)); @@ -3245,6 +3351,7 @@ sky2->speed = -1; sky2->advertising = sky2_supported_modes(hw); sky2->rx_csum = 1; + sky2->wol = wol; spin_lock_init(&sky2->phy_lock); sky2->tx_pending = TX_DEF_PENDING; @@ -3347,12 +3454,24 @@ return err; } +static int __devinit wol_enabled(struct pci_dev *dev) +{ + int pm = pci_find_capability(dev, PCI_CAP_ID_PM); + u16 value; + + if (!pm) + return 0; + if (pci_read_config_word(dev, pm + PCI_PM_CTRL, &value)) + return 0; + return value & PCI_PM_CTRL_PME_ENABLE; +} + static int __devinit sky2_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { struct net_device *dev; struct sky2_hw *hw; - int err, using_dac = 0; + int err, using_dac = 0, wol_default; err = pci_enable_device(pdev); if (err) { @@ -3389,6 +3508,8 @@ } } + wol_default = wol_enabled(pdev) ? WAKE_MAGIC : 0; + err = -ENOMEM; hw = kzalloc(sizeof(*hw), GFP_KERNEL); if (!hw) { @@ -3424,7 +3545,7 @@ if (!hw->st_le) goto err_out_iounmap; - err = sky2_reset(hw); + err = sky2_init(hw); if (err) goto err_out_iounmap; @@ -3433,7 +3554,9 @@ pdev->irq, yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL], hw->chip_id, hw->chip_rev); - dev = sky2_init_netdev(hw, 0, using_dac); + sky2_reset(hw); + + dev = sky2_init_netdev(hw, 0, using_dac, wol_default); if (!dev) { err = -ENOMEM; goto err_out_free_pci; @@ -3468,7 +3591,7 @@ if (hw->ports > 1) { struct net_device *dev1; - dev1 = sky2_init_netdev(hw, 1, using_dac); + dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default); if (!dev1) { printk(KERN_WARNING PFX "allocation of second port failed\n"); @@ -3555,23 +3678,29 @@ static int sky2_suspend(struct pci_dev *pdev, pm_message_t state) { struct sky2_hw *hw = pci_get_drvdata(pdev); - int i; + int i, wol = 0; del_timer_sync(&hw->idle_timer); netif_poll_disable(hw->dev[0]); for (i = 0; i < hw->ports; i++) { struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); - if (netif_running(dev)) { + if (netif_running(dev)) sky2_down(dev); - netif_device_detach(dev); - } + + if (sky2->wol) + sky2_wol_init(sky2); + + wol |= sky2->wol; } sky2_write32(hw, B0_IMSK, 0); sky2_power_aux(hw); + pci_save_state(pdev); + pci_enable_wake(pdev, pci_choose_state(pdev, state), wol); pci_set_power_state(pdev, pci_choose_state(pdev, state)); return 0; @@ -3591,18 +3720,13 @@ goto out; pci_enable_wake(pdev, PCI_D0, 0); - - err = sky2_reset(hw); - if (err) - goto out; + sky2_reset(hw); sky2_write32(hw, B0_IMSK, Y2_IS_BASE); for (i = 0; i < hw->ports; i++) { struct net_device *dev = hw->dev[i]; if (netif_running(dev)) { - netif_device_attach(dev); - err = sky2_up(dev); if (err) { printk(KERN_ERR PFX "%s: could not up: %d\n", @@ -3646,6 +3770,35 @@ } #endif +static void sky2_shutdown(struct pci_dev *pdev) +{ + struct sky2_hw *hw = pci_get_drvdata(pdev); + int i, wol = 0; + + del_timer_sync(&hw->idle_timer); + netif_poll_disable(hw->dev[0]); + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (sky2->wol) { + wol = 1; + sky2_wol_init(sky2); + } + } + + if (wol) + sky2_power_aux(hw); + + pci_enable_wake(pdev, PCI_D3hot, wol); + pci_enable_wake(pdev, PCI_D3cold, wol); + + pci_disable_device(pdev); + pci_set_power_state(pdev, PCI_D3hot); + +} + static struct pci_driver sky2_driver = { .name = DRV_NAME, .id_table = sky2_id_table, @@ -3657,6 +3810,7 @@ .suspend_late = sky2_suspend_late, .resume_early = sky2_resume_early, #endif + .shutdown = sky2_shutdown, }; static int __init sky2_init_module(void) --- sky2-2.6.orig/drivers/net/sky2.h 2007-01-26 11:26:52.000000000 -0800 +++ sky2-2.6/drivers/net/sky2.h 2007-01-26 11:26:55.000000000 -0800 @@ -32,6 +32,7 @@ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */ + PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */ }; enum pci_dev_reg_2 { @@ -837,33 +838,27 @@ GMAC_LINK_CTRL = 0x0f10,/* 16 bit Link Control Reg */ /* Wake-up Frame Pattern Match Control Registers (YUKON only) */ - - WOL_REG_OFFS = 0x20,/* HW-Bug: Address is + 0x20 against spec. */ - WOL_CTRL_STAT = 0x0f20,/* 16 bit WOL Control/Status Reg */ WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */ WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */ WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */ - WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */ - WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */ WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */ /* WOL Pattern Length Registers (YUKON only) */ - WOL_PATT_LEN_LO = 0x0f30,/* 32 bit WOL Pattern Length 3..0 */ WOL_PATT_LEN_HI = 0x0f34,/* 24 bit WOL Pattern Length 6..4 */ /* WOL Pattern Counter Registers (YUKON only) */ - - WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */ WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */ }; +#define WOL_REGS(port, x) (x + (port)*0x80) enum { WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */ WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */ }; +#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400) enum { BASE_GMAC_1 = 0x2800,/* GMAC 1 registers */ @@ -1715,14 +1710,17 @@ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ #define GMAC_DEF_MSK GM_IS_TX_FF_UR +}; /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ - /* Bits 15.. 2: reserved */ +enum { /* Bits 15.. 2: reserved */ GMLC_RST_CLR = 1<<1, /* Clear GMAC Link Reset */ GMLC_RST_SET = 1<<0, /* Set GMAC Link Reset */ +}; /* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */ +enum { WOL_CTL_LINK_CHG_OCC = 1<<15, WOL_CTL_MAGIC_PKT_OCC = 1<<14, WOL_CTL_PATTERN_OCC = 1<<13, @@ -1741,17 +1739,6 @@ WOL_CTL_DIS_PATTERN_UNIT = 1<<0, }; -#define WOL_CTL_DEFAULT \ - (WOL_CTL_DIS_PME_ON_LINK_CHG | \ - WOL_CTL_DIS_PME_ON_PATTERN | \ - WOL_CTL_DIS_PME_ON_MAGIC_PKT | \ - WOL_CTL_DIS_LINK_CHG_UNIT | \ - WOL_CTL_DIS_PATTERN_UNIT | \ - WOL_CTL_DIS_MAGIC_PKT_UNIT) - -/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */ -#define WOL_CTL_PATT_ENA(x) (1 << (x)) - /* Control flags */ enum { @@ -1875,6 +1862,7 @@ u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */ u8 rx_csum; + u8 wol; enum flow_control flow_mode; enum flow_control flow_status; -- Stephen Hemminger - To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html