This code inherited from the sk98lin driver is incorrect on the Yukon2. The GPHY_CTRL register values are specific to the internal PHY of the chip and the values used were leftovers. Driver was setting bit 13 which is now the INT polarity for the PHY! Signed-off-by: Stephen Hemminger --- a/drivers/net/sky2.c 2007-05-23 08:44:09.000000000 -0700 +++ b/drivers/net/sky2.c 2007-05-23 08:47:11.000000000 -0700 @@ -658,7 +658,7 @@ static void sky2_mac_init(struct sky2_hw const u8 *addr = hw->dev[port]->dev_addr; sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); - sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR|GPC_ENA_PAUSE); + sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); --- a/drivers/net/sky2.h 2007-05-23 08:44:09.000000000 -0700 +++ b/drivers/net/sky2.h 2007-05-23 08:47:11.000000000 -0700 @@ -1732,28 +1732,6 @@ enum { /* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */ enum { - GPC_SEL_BDT = 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */ - GPC_INT_POL_HI = 1<<27, /* IRQ Polarity is Active HIGH */ - GPC_75_OHM = 1<<26, /* Use 75 Ohm Termination instead of 50 */ - GPC_DIS_FC = 1<<25, /* Disable Automatic Fiber/Copper Detection */ - GPC_DIS_SLEEP = 1<<24, /* Disable Energy Detect */ - GPC_HWCFG_M_3 = 1<<23, /* HWCFG_MODE[3] */ - GPC_HWCFG_M_2 = 1<<22, /* HWCFG_MODE[2] */ - GPC_HWCFG_M_1 = 1<<21, /* HWCFG_MODE[1] */ - GPC_HWCFG_M_0 = 1<<20, /* HWCFG_MODE[0] */ - GPC_ANEG_0 = 1<<19, /* ANEG[0] */ - GPC_ENA_XC = 1<<18, /* Enable MDI crossover */ - GPC_DIS_125 = 1<<17, /* Disable 125 MHz clock */ - GPC_ANEG_3 = 1<<16, /* ANEG[3] */ - GPC_ANEG_2 = 1<<15, /* ANEG[2] */ - GPC_ANEG_1 = 1<<14, /* ANEG[1] */ - GPC_ENA_PAUSE = 1<<13, /* Enable Pause (SYM_OR_REM) */ - GPC_PHYADDR_4 = 1<<12, /* Bit 4 of Phy Addr */ - GPC_PHYADDR_3 = 1<<11, /* Bit 3 of Phy Addr */ - GPC_PHYADDR_2 = 1<<10, /* Bit 2 of Phy Addr */ - GPC_PHYADDR_1 = 1<<9, /* Bit 1 of Phy Addr */ - GPC_PHYADDR_0 = 1<<8, /* Bit 0 of Phy Addr */ - /* Bits 7..2: reserved */ GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */ GPC_RST_SET = 1<<0, /* Set GPHY Reset */ }; -- Stephen Hemminger - To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html