| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <6278d2220707110315h55b69c69r66420377afa703da@mail.gmail.com>
Date: Wed, 11 Jul 2007 11:15:20 +0100
From: "Daniel J Blueman" <daniel.blueman@...il.com>
To: "Stephen Hemminger" <shemminger@...ux-foundation.org>
Cc: "Linux Netdev" <netdev@...r.kernel.org>
Subject: Re: sky2 hangs without any messages
On 05/07/07, Stephen Hemminger <shemminger@...ux-foundation.org> wrote:
> Well, it didn't fix my test, but it made it better. The following seemed
> to work longer...
>
> --- a/drivers/net/sky2.c 2007-07-05 09:09:45.000000000 -0700
> +++ b/drivers/net/sky2.c 2007-07-05 09:09:51.000000000 -0700
> @@ -2490,6 +2490,13 @@ static int sky2_poll(struct net_device *
>
> work_done = sky2_status_intr(hw, work_limit);
> if (work_done < work_limit) {
> + /* Bug/Errata workaround?
> + * Need to kick the TX irq moderation timer.
> + */
> + if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_START) {
> + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
> + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
> + }
> netif_rx_complete(dev0);
>
> /* end of interrupt, re-enables also acts as I/O synchronization */
I spoke too soon on this. With the above patch on 2.6.22-rc7, it
failed much sooner than the previous patch with the
read32(B0_Y2_SP_LISR); I'll try to reproduce with the older patch.
Note the ifconfig error/dropped/frame count at the time of failure:
# ethtool -g lan0
Ring parameters for lan0:
Pre-set maximums:
RX: 168
RX Mini: 0
RX Jumbo: 0
TX: 511
Current hardware settings:
RX: 168
RX Mini: 0
RX Jumbo: 0
TX: 511
# ethtool -a lan0
Pause parameters for lan0:
Autonegotiate: on
RX: on
TX: on
# ethtool -c lan0
Coalesce parameters for lan0:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 100
rx-frames: 16
rx-usecs-irq: 20
rx-frames-irq: 16
tx-usecs: 1000
tx-frames: 10
tx-usecs-irq: 0
tx-frames-irq: 0
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
# ethtool -k lan0
Offload parameters for lan0:
Cannot get device udp large send offload settings: Operation not supported
rx-checksumming: on
tx-checksumming: on
scatter-gather: on
tcp segmentation offload: on
udp fragmentation offload: off
generic segmentation offload: off
# ethtool -S lan0
NIC statistics:
tx_bytes: 2624901638
rx_bytes: 125131827
tx_broadcast: 177
rx_broadcast: 245
tx_multicast: 0
rx_multicast: 0
tx_unicast: 1818345
rx_unicast: 973657
tx_mac_pause: 0
rx_mac_pause: 0
collisions: 0
late_collision: 0
aborted: 0
single_collisions: 0
multi_collisions: 0
rx_short: 0
rx_runt: 0
rx_64_byte_packets: 2475
rx_65_to_127_byte_packets: 891841
rx_128_to_255_byte_packets: 3748
rx_256_to_511_byte_packets: 42082
rx_512_to_1023_byte_packets: 3133
rx_1024_to_1518_byte_packets: 30623
rx_1518_to_max_byte_packets: 0
rx_too_long: 0
rx_fifo_overflow: 0
rx_jabber: 0
rx_fcs_error: 0
tx_64_byte_packets: 1429
tx_65_to_127_byte_packets: 35881
tx_128_to_255_byte_packets: 17013
tx_256_to_511_byte_packets: 25872
tx_512_to_1023_byte_packets: 30901
tx_1024_to_1518_byte_packets: 1707426
tx_1519_to_max_byte_packets: 0
tx_fifo_underrun: 0
# ifconfig lan0
lan0 Link encap:Ethernet HWaddr 00:03:2D:05:9C:27
inet addr:192.168.0.250 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:973893 errors:1 dropped:1 overruns:0 frame:1
TX packets:819179 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:107601061 (102.6 MiB) TX bytes:2551658362 (2.3 GiB)
Interrupt:16
# dmesg
...
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
sky2 0000:01:00.0: v1.14 addr 0xdfbfc000 irq 16 Yukon-EC (0xb6) rev 1
sky2 eth1: addr 00:03:2d:05:9c:27
sky2 lan0: enabling interface
sky2 lan0: ram buffer 48K
sky2 lan0: Link is up at 1000 Mbps, full duplex, flow control both
...
lan0: hw csum failure.
[<b02b707c>] __skb_checksum_complete_head+0x5c/0x60
[<b02b7088>] __skb_checksum_complete+0x8/0x10
[<b0313aab>] nf_ip_checksum+0xbb/0x130
[<b02d8b9c>] udp_error+0x13c/0x1b0
[<b02ba4cd>] dev_hard_start_xmit+0x1cd/0x230
[<b02e93c0>] ip_finish_output+0x0/0x260
[<b02d8a60>] udp_error+0x0/0x1b0
[<b02d5736>] nf_conntrack_in+0xf6/0x4d0
[<b02bbe85>] dev_queue_xmit+0x95/0x260
[<b02eac51>] ip_output+0x141/0x2e0
[<b02e93c0>] ip_finish_output+0x0/0x260
[<b02ea20f>] ip_queue_xmit+0x1cf/0x3d0
[<b02e7cd0>] dst_output+0x0/0x10
[<b02d33a3>] nf_iterate+0x63/0x90
[<b02e4fb0>] ip_rcv_finish+0x0/0x280
[<b02d3519>] nf_hook_slow+0x59/0xe0
[<b02e4fb0>] ip_rcv_finish+0x0/0x280
[<b02e5740>] ip_rcv+0x2f0/0x4d0
[<b02e4fb0>] ip_rcv_finish+0x0/0x280
[<b0321d56>] packet_rcv_spkt+0xe6/0x180
[<b02b9f38>] netif_receive_skb+0x1f8/0x2e0
[<f0840db1>] sky2_poll+0x351/0x9c0 [sky2]
[<b01206b4>] run_timer_softirq+0x124/0x180
[<b02bbc6c>] net_rx_action+0x5c/0x100
[<b011dd62>] __do_softirq+0x42/0x90
[<b010642c>] do_softirq+0x5c/0xb0
[<b0139e30>] handle_edge_irq+0x0/0xe0
[<b011dc8a>] irq_exit+0x5a/0x60
[<b01064ec>] do_IRQ+0x6c/0xb0
[<b0104807>] common_interrupt+0x23/0x28
[<b0420000>] xt_tcpudp_init+0x0/0x10
[<b0102c9a>] default_idle+0x2a/0x40
[<b01023d3>] cpu_idle+0x43/0x70
[<b0404b25>] start_kernel+0x215/0x2a0
[<b0404450>] unknown_bootoption+0x0/0x260
=======================
Daniel
--
Daniel J Blueman
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists