| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20070806150525.GC24308@hall.aurel32.net>
Date: Mon, 6 Aug 2007 17:05:25 +0200
From: Aurelien Jarno <aurelien@...el32.net>
To: Michael Buesch <mb@...sch.de>, netdev@...r.kernel.org
Cc: Felix Fietkau <nbd@...nwrt.org>
Subject: [PATCH 2/3] Use SSB EXTIF in SSB MIPS core driver
The patch below against 2.6.23-rc1-mm2 uses the functions added in the
previous patch to do serial and timing initializations for EXTIF,
currently marked as TODO. It also implements the ssb_cpu_clock() and
export it. This function is needed to support the BCM947xx CPUs.
Cc: Felix Fietkau <nbd@...nwrt.org>
Signed-off-by: Aurelien Jarno <aurelien@...el32.net>
--- a/drivers/ssb/driver_mipscore.c
+++ b/drivers/ssb/driver_mipscore.c
@@ -117,51 +117,10 @@
ssb_write32(mdev, SSB_IPSFLAG, irqflag);
}
-/* XXX: leave here or move into separate extif driver? */
-static int ssb_extif_serial_init(struct ssb_device *dev, struct ssb_serial_ports *ports)
-{
-
-}
-
-
static void ssb_mips_serial_init(struct ssb_mipscore *mcore)
{
struct ssb_bus *bus = mcore->dev->bus;
- //TODO if (EXTIF available
-#if 0
- extifregs_t *eir = (extifregs_t *) regs;
- sbconfig_t *sb;
-
- /* Determine external UART register base */
- sb = (sbconfig_t *)((ulong) eir + SBCONFIGOFF);
- base = EXTIF_CFGIF_BASE(sb_base(R_REG(&sb->sbadmatch1)));
-
- /* Determine IRQ */
- irq = sb_irq(sbh);
-
- /* Disable GPIO interrupt initially */
- W_REG(&eir->gpiointpolarity, 0);
- W_REG(&eir->gpiointmask, 0);
-
- /* Search for external UARTs */
- n = 2;
- for (i = 0; i < 2; i++) {
- regs = (void *) REG_MAP(base + (i * 8), 8);
- if (BCMINIT(serial_exists)(regs)) {
- /* Set GPIO 1 to be the external UART IRQ */
- W_REG(&eir->gpiointmask, 2);
- if (add)
- add(regs, irq, 13500000, 0);
- }
- }
-
- /* Add internal UART if enabled */
- if (R_REG(&eir->corecontrol) & CC_UE)
- if (add)
- add((void *) &eir->uartdata, irq, sb_clock(sbh), 2);
-
-#endif
if (bus->extif.dev)
mcore->nr_serial_ports = ssb_extif_serial_init(&bus->extif, mcore->serial_ports);
else if (bus->chipco.dev)
@@ -183,9 +142,29 @@
}
}
-
-static void ssb_cpu_clock(struct ssb_mipscore *mcore)
+u32 ssb_cpu_clock(struct ssb_mipscore *mcore)
{
+ struct ssb_bus *bus = mcore->dev->bus;
+ u32 pll_type, n, m, rate = 0;
+
+ if (bus->extif.dev) {
+ ssb_extif_get_clockcontrol(&bus->extif, &pll_type, &n, &m);
+ } else if (bus->chipco.dev) {
+ ssb_chipco_get_clockcpu(&bus->chipco, &pll_type, &n, &m);
+ } else
+ return 0;
+
+ if ((pll_type == SSB_PLLTYPE_5) || (bus->chip_id == 0x5365)) {
+ rate = 200000000;
+ } else {
+ rate = ssb_calc_clock_rate(pll_type, n, m);
+ }
+
+ if (pll_type == SSB_PLLTYPE_6) {
+ rate *= 2;
+ }
+
+ return rate;
}
void ssb_mipscore_init(struct ssb_mipscore *mcore)
@@ -205,27 +184,9 @@
hz = 100000000;
ns = 1000000000 / hz;
-//TODO
-#if 0
- if (have EXTIF) {
- /* Initialize extif so we can get to the LEDs and external UART */
- W_REG(&eir->prog_config, CF_EN);
-
- /* Set timing for the flash */
- tmp = CEIL(10, ns) << FW_W3_SHIFT; /* W3 = 10nS */
- tmp = tmp | (CEIL(40, ns) << FW_W1_SHIFT); /* W1 = 40nS */
- tmp = tmp | CEIL(120, ns); /* W0 = 120nS */
- W_REG(&eir->prog_waitcount, tmp); /* 0x01020a0c for a 100Mhz clock */
-
- /* Set programmable interface timing for external uart */
- tmp = CEIL(10, ns) << FW_W3_SHIFT; /* W3 = 10nS */
- tmp = tmp | (CEIL(20, ns) << FW_W2_SHIFT); /* W2 = 20nS */
- tmp = tmp | (CEIL(100, ns) << FW_W1_SHIFT); /* W1 = 100nS */
- tmp = tmp | CEIL(120, ns); /* W0 = 120nS */
- W_REG(&eir->prog_waitcount, tmp);
- }
-#endif
- if (bus->chipco.dev)
+ if (bus->extif.dev)
+ ssb_extif_timing_init(&bus->extif, ns);
+ else if (bus->chipco.dev)
ssb_chipco_timing_init(&bus->chipco, ns);
/* Assign IRQs to all cores on the bus, start with irq line 2, because serial usually takes 1 */
--- a/drivers/ssb/main.c
+++ b/drivers/ssb/main.c
@@ -819,12 +819,13 @@
u32 plltype;
u32 clkctl_n, clkctl_m;
- //TODO if EXTIF: PLLTYPE == 1, read n from clockcontrol_n, m from clockcontrol_sb
-
- if (bus->chipco.dev) {
+ if (bus->extif.dev)
+ ssb_extif_get_clockcontrol(&bus->extif, &plltype,
+ &clkctl_n, &clkctl_m);
+ else if (bus->chipco.dev)
ssb_chipco_get_clockcontrol(&bus->chipco, &plltype,
&clkctl_n, &clkctl_m);
- } else
+ else
return 0;
if (bus->chip_id == 0x5365) {
--- a/include/linux/ssb/ssb_driver_mips.h
+++ b/include/linux/ssb/ssb_driver_mips.h
@@ -25,6 +25,7 @@
};
extern void ssb_mipscore_init(struct ssb_mipscore *mcore);
+extern u32 ssb_cpu_clock(struct ssb_mipscore *mcore);
extern unsigned int ssb_mips_irq(struct ssb_device *dev);
--
.''`. Aurelien Jarno | GPG: 1024D/F1BCDB73
: :' : Debian developer | Electrical Engineer
`. `' aurel32@...ian.org | aurelien@...el32.net
`- people.debian.org/~aurel32 | www.aurel32.net
-
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists