--- /home/jan/dmesg-2.6.20 2007-09-07 17:17:09.000000000 +0200 +++ dmesg-2.6.23-rc5 2007-09-07 18:13:09.000000000 +0200 @@ -1,4 +1,4 @@ -Linux version 2.6.20-1-amd64 (Debian 2.6.20-3) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Apr 24 21:10:58 UTC 2007 +Linux version 2.6.23-rc5-amd64 (Debian 2.6.23~rc5-1~experimental.1~snapshot.9462) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14+1)) #1 SMP Thu Sep 6 06:18:52 UTC 2007 Command line: root=/dev/sda6 ro quiet vga=791 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ec00 (usable) @@ -14,18 +14,19 @@ Entering add_active_range(0, 256, 520080) 1 entries of 3200 used end_pfn_map = 1048576 DMI 2.4 present. -ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fad70 -ACPI: XSDT (v001 NEC 0x05000730 MSFT 0x00000097) @ 0x000000007ef90100 -ACPI: FADT (v003 MSTEST OEMFACP 0x05000730 MSFT 0x00000097) @ 0x000000007ef90290 -ACPI: MADT (v001 MSTEST OEMAPIC 0x05000730 MSFT 0x00000097) @ 0x000000007ef90390 -ACPI: MCFG (v001 MSTEST OEMMCFG 0x05000730 MSFT 0x00000097) @ 0x000000007ef90400 -ACPI: SLIC (v001 NEC 0x05000730 MSFT 0x00000097) @ 0x000000007ef90440 -ACPI: OEMB (v001 MSTEST AMI_OEM 0x05000730 MSFT 0x00000097) @ 0x000000007ef9e040 -ACPI: HPET (v001 MSTEST OEMHPET 0x05000730 MSFT 0x00000097) @ 0x000000007ef9a250 -ACPI: GSCI (v001 MSTEST GMCHSCI 0x05000730 MSFT 0x00000097) @ 0x000000007ef9e0c0 -ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x000000007efa00f0 -ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x000000007efa02b0 -ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x0000000000000000 +ACPI: RSDP 000FAD70, 0024 (r2 ACPIAM) +ACPI: XSDT 7EF90100, 006C (r1 NEC 5000730 MSFT 97) +ACPI: FACP 7EF90290, 00F4 (r3 MSTEST OEMFACP 5000730 MSFT 97) +ACPI: DSDT 7EF905C0, 9C85 (r1 A0579 A0579000 0 INTL 20060113) +ACPI: FACS 7EF9E000, 0040 +ACPI: APIC 7EF90390, 006C (r1 MSTEST OEMAPIC 5000730 MSFT 97) +ACPI: MCFG 7EF90400, 003C (r1 MSTEST OEMMCFG 5000730 MSFT 97) +ACPI: SLIC 7EF90440, 0176 (r1 NEC 5000730 MSFT 97) +ACPI: OEMB 7EF9E040, 007B (r1 MSTEST AMI_OEM 5000730 MSFT 97) +ACPI: HPET 7EF9A250, 0038 (r1 MSTEST OEMHPET 5000730 MSFT 97) +ACPI: GSCI 7EF9E0C0, 2024 (r1 MSTEST GMCHSCI 5000730 MSFT 97) +ACPI: SSDT 7EFA00F0, 01BF (r1 AMI CPU1PM 1 INTL 20060113) +ACPI: SSDT 7EFA02B0, 0133 (r1 AMI CPU2PM 1 INTL 20060113) No NUMA configuration found Faking a node at 0000000000000000-000000007ef90000 Entering add_active_range(0, 0, 158) 0 entries of 3200 used @@ -35,16 +36,18 @@ DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 +Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 158 0: 256 -> 520080 On node 0 totalpages: 519982 DMA zone: 56 pages used for memmap - DMA zone: 972 pages reserved - DMA zone: 2970 pages, LIFO batch:0 + DMA zone: 1044 pages reserved + DMA zone: 2898 pages, LIFO batch:0 DMA32 zone: 7054 pages used for memmap DMA32 zone: 508930 pages, LIFO batch:31 Normal zone: 0 pages used for memmap + Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) @@ -60,31 +63,35 @@ ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. -Setting APIC routing to physical flat +Setting APIC routing to flat ACPI: HPET id: 0x8086a202 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information -Nosave address range: 000000000009e000 - 000000000009f000 -Nosave address range: 000000000009f000 - 00000000000a0000 -Nosave address range: 00000000000a0000 - 00000000000e4000 -Nosave address range: 00000000000e4000 - 0000000000100000 +swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000 +swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 +swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000 +swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000 Allocating PCI resources starting at 80000000 (gap: 7f000000:7fe00000) SMP: Allowing 4 CPUs, 2 hotplug CPUs -PERCPU: Allocating 36992 bytes of per cpu data -Built 1 zonelists. Total pages: 511900 +PERCPU: Allocating 35176 bytes of per cpu data +Built 1 zonelists in Node order. Total pages: 511828 +Policy zone: DMA32 Kernel command line: root=/dev/sda6 ro quiet vga=791 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) +Extended CMOS year: 2000 +time.c: Detected 2399.997 MHz processor. Console: colour dummy device 80x25 -Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) -Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) +console [tty0] enabled Checking aperture... Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! -Memory: 2038324k/2080320k available (1970k kernel code, 41604k reserved, 920k data, 284k init) -Calibrating delay using timer specific routine.. 4804.04 BogoMIPS (lpj=9608092) +Memory: 2041096k/2080320k available (2066k kernel code, 38832k reserved, 977k data, 304k init) +Calibrating delay using timer specific routine.. 4803.34 BogoMIPS (lpj=9606690) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized +Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) +Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K @@ -94,14 +101,14 @@ CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) SMP alternatives: switching to UP code -ACPI: Core revision 20060707 +ACPI: Core revision 20070126 Using local APIC timer interrupts. -result 16666675 +result 16666629 Detected 16.666 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 -Calibrating delay using timer specific routine.. 4800.01 BogoMIPS (lpj=9600034) +Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=9600060) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU 1/1 -> Node 0 @@ -109,25 +116,20 @@ CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06 +checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs -testing NMI watchdog ... OK. -time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer. -time.c: Detected 2400.003 MHz processor. -migration_cost=20 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 +ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled +ACPI: (supports S0 S1 S3) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) -PCI: Probing PCI hardware (bus 00) PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 0480-04bf claimed by ICH6 GPIO -Boot video device is 0000:01:00.0 -0000:02:00.0: cannot adjust BAR2 (not I/O) -0000:02:00.0: cannot adjust BAR3 (not I/O) PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] @@ -142,8 +144,10 @@ ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15) +ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CD, should be C4 [20070126] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init +ACPI: bus type pnp registered pnp: ACPI device : hid PNP0A08 pnp: ACPI device : hid PNP0C01 pnp: ACPI device : hid PNP0200 @@ -161,26 +165,39 @@ pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0C01 pnp: PnP ACPI: found 16 devices +ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report -PCI: Cannot allocate resource region 2 of device 0000:02:00.0 -PCI: Cannot allocate resource region 3 of device 0000:02:00.0 NET: Registered protocol family 8 NET: Registered protocol family 20 +PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz -PCI-GART: No AMD northbridge found. +ACPI: RTC can wake from S4 +Time: tsc clocksource has been installed. pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:01' and the driver 'system' +pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved pnp: match found with the PnP device '00:08' and the driver 'system' pnp: 00:08: ioport range 0x290-0x297 has been reserved pnp: match found with the PnP device '00:09' and the driver 'system' +pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved +pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved +pnp: 00:09: iomem range 0xff9fa000-0xff9fafff has been reserved +pnp: 00:09: iomem range 0xfff00000-0xfffffffe could not be reserved pnp: match found with the PnP device '00:0b' and the driver 'system' +pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved +pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: match found with the PnP device '00:0e' and the driver 'system' +pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved pnp: match found with the PnP device '00:0f' and the driver 'system' +pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved +pnp: 00:0f: iomem range 0xc0000-0xcffff has been reserved +pnp: 00:0f: iomem range 0xe0000-0xfffff could not be reserved +pnp: 00:0f: iomem range 0x100000-0x7effffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: 8000-afff MEM window: ff700000-ff7fffff @@ -206,20 +223,21 @@ PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) -TCP established hash table entries: 262144 (order: 10, 4194304 bytes) +TCP established hash table entries: 262144 (order: 10, 6291456 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered checking if image is initramfs... it is -Freeing initrd memory: 5937k freed +Freeing initrd memory: 5950k freed audit: initializing netlink socket (disabled) -audit(1181990747.912:1): initialized +audit(1189181505.780:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) +Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] @@ -231,7 +249,7 @@ assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] -vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 3072k, total 16384k +vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000b00000, using 3072k, total 16384k vesafb: mode is 1024x768x16, linelength=2048, pages=9 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 @@ -239,7 +257,7 @@ fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy -Linux agpgart interface v0.101 (c) Dave Jones +Linux agpgart interface v0.102 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A pnp: the driver 'serial' has been registered @@ -257,11 +275,10 @@ TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 -ACPI: (supports S0 S1 S3 S4 S5) -Freeing unused kernel memory: 284k freed +Freeing unused kernel memory: 304k freed input: AT Translated Set 2 keyboard as /class/input/input0 -ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707] -ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707] +ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126] +ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126] USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 @@ -274,10 +291,9 @@ Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx pnp: the driver 'ide' has been registered -SCSI subsystem initialized -ieee1394: Initialized config rom entry `ip1394' Floppy drive(s): fd0 is 1.44M -libata version 2.00 loaded. +SCSI subsystem initialized +libata version 2.21 loaded. FDC 0 is a post-1991 82077 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1a.1 to 64 @@ -312,8 +328,42 @@ hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19 -skge 1.9 addr 0xff9f8000 irq 19 chip Yukon-Lite rev 9 -skge eth0: addr 00:18:f3:90:8e:7b +PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 +skge 0000:04:04.0: cannot obtain PCI resources +ACPI: PCI interrupt for device 0000:04:04.0 disabled +skge: probe of 0000:04:04.0 failed with error -16 +ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21 +firewire_ohci: Added fw-ohci device 0000:04:03.0, OHCI version 1.10 +ahci 0000:00:1f.2: version 2.3 +ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 +firewire_core: created new fw device fw0 (0 config rom retries, S400) +ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode +ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part +PCI: Setting latency timer of device 0000:00:1f.2 to 64 +scsi0 : ahci +scsi1 : ahci +scsi2 : ahci +scsi3 : ahci +scsi4 : ahci +scsi5 : ahci +ata1: SATA max UDMA/133 cmd 0xffffc20000ac2900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276 +ata2: SATA max UDMA/133 cmd 0xffffc20000ac2980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276 +ata3: DUMMY +ata4: DUMMY +ata5: SATA max UDMA/133 cmd 0xffffc20000ac2b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276 +ata6: SATA max UDMA/133 cmd 0xffffc20000ac2b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276 +ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) +ata1.00: ATA-7: SAMSUNG HD401LJ, ZZ100-15, max UDMA7 +ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (not used) +ata1.00: configured for UDMA/133 +ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) +ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H30N, 1.01, max UDMA/100 +ata2.00: configured for UDMA/100 +ata5: SATA link down (SStatus 0 SControl 300) +ata6: SATA link down (SStatus 0 SControl 300) +scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD401LJ ZZ10 PQ: 0 ANSI: 5 +scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H30N 1.01 PQ: 0 ANSI: 5 +ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller @@ -325,6 +375,15 @@ usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 4 ports detected +ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode +ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part +PCI: Setting latency timer of device 0000:02:00.0 to 64 +scsi6 : ahci +scsi7 : ahci +ata7: SATA max UDMA/133 cmd 0xffffc20000ac4100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16 +ata8: SATA max UDMA/133 cmd 0xffffc20000ac4180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16 +ata7: SATA link down (SStatus 0 SControl 300) +ata8: SATA link down (SStatus 0 SControl 300) ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller @@ -336,114 +395,69 @@ usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 6 ports detected -ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21 -ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[ff9ff000-ff9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8] -ahci 0000:00:1f.2: version 2.0 -ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 -PCI: Setting latency timer of device 0000:00:1f.2 to 64 -ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode -ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part -ata1: SATA max UDMA/133 cmd 0xFFFFC20000056900 ctl 0x0 bmdma 0x0 irq 1276 -ata2: SATA max UDMA/133 cmd 0xFFFFC20000056980 ctl 0x0 bmdma 0x0 irq 1276 -ata3: DUMMY -ata4: DUMMY -ata5: SATA max UDMA/133 cmd 0xFFFFC20000056B00 ctl 0x0 bmdma 0x0 irq 1276 -ata6: SATA max UDMA/133 cmd 0xFFFFC20000056B80 ctl 0x0 bmdma 0x0 irq 1276 -scsi0 : ahci -ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000ec51d2] -ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -ata1.00: ATA-7, max UDMA7, 781422768 sectors: LBA48 NCQ (depth 31/32) -ata1.00: configured for UDMA/133 -scsi1 : ahci -ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) -ata2.00: ATAPI, max UDMA/100 -ata2.00: configured for UDMA/100 -scsi2 : ahci -scsi3 : ahci -scsi4 : ahci -ata5: SATA link down (SStatus 0 SControl 300) -scsi5 : ahci -ata6: SATA link down (SStatus 0 SControl 300) -scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD401LJ ZZ10 PQ: 0 ANSI: 5 -scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H30N 1.01 PQ: 0 ANSI: 5 -PCI: Device 0000:02:00.0 not available because of resource collisions -ahci: probe of 0000:02:00.0 failed with error -22 -JMB363: IDE controller at PCI slot 0000:02:00.0 -PCI: Device 0000:02:00.0 not available because of resource collisions -ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 -JMB363: BIOS configuration fixed. +sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB) +sd 0:0:0:0: [sda] Write Protect is off +sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 +sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA +sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB) +sd 0:0:0:0: [sda] Write Protect is off +sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 +sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA + sda: sda1 sda2 sda3 < sda5 sda6 sda7 > +sd 0:0:0:0: [sda] Attached SCSI disk +JMB363: IDE controller at PCI slot 0000:02:00.1 +PCI: Enabling device 0000:02:00.1 (0000 -> 0001) +ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17 JMB363: chipset revision 2 -JMB363: 100% native mode on irq 16 -JMB363: dma_base is invalid -ide0: JMB363 Bus-Master DMA disabled (BIOS) -JMB363: dma_base is invalid -ide1: JMB363 Bus-Master DMA disabled (BIOS) +JMB363: 100% native mode on irq 17 +PCI: Setting latency timer of device 0000:02:00.1 to 64 + ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA + ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... -SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB) -sda: Write Protect is off -sda: Mode Sense: 00 3a 00 00 -SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA -SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB) -sda: Write Protect is off -sda: Mode Sense: 00 3a 00 00 -SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA - sda: sda1 sda2 sda3 < sda5 sda6 > -sd 0:0:0:0: Attached scsi disk sda sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 +hdb: WDC WD400BB-00AUA1, ATA DISK drive +hdb: selected mode 0x45 +ide0 at 0xbc00-0xbc07,0xb882 on irq 17 Probing IDE interface ide1... -JMB363: IDE controller at PCI slot 0000:02:00.1 -PCI: Enabling device 0000:02:00.1 (0000 -> 0001) -ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17 -JMB363: chipset revision 2 -JMB363: 100% native mode on irq 17 -PCI: Setting latency timer of device 0000:02:00.1 to 64 - ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:DMA, hdf:DMA - ide3: BM-DMA at 0xb408-0xb40f, BIOS settings: hdg:pio, hdh:pio -Probing IDE interface ide2... -hdf: WDC WD400BB-00AUA1, ATA DISK drive -hdf: hw_config=6b00 -hdf: hw_config=6b00 -ide2 at 0xbc00-0xbc07,0xb882 on irq 17 -Probing IDE interface ide3... -hdf: max request size: 128KiB -hdf: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63<6>hdf: hw_config=6b00 -, UDMA(100) -hdf: cache flushes not supported - hdf: hdf1 hdf2 < hdf5 hdf6 hdf7 hdf8 hdf9 hdf10 hdf11 > +hdb: max request size: 128KiB +hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) +hdb: cache flushes not supported + hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 > kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. -eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) -PCI: Enabling device 0000:00:1f.3 (0001 -> 0003) -ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18 -agpgart: Detected an Intel 965G Chipset. -agpgart: AGP aperture is 256M @ 0x0 -iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006) +input: PC Speaker as /class/input/input1 +iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) -input: PC Speaker as /class/input/input1 +input: Power Button (FF) as /class/input/input2 +ACPI: Power Button (FF) [PWRF] +input: Power Button (CM) as /class/input/input3 +ACPI: Power Button (CM) [PWRB] +ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 +PCI: Setting latency timer of device 0000:00:1b.0 to 64 +hda_codec: Unknown model for AD1988, trying auto-probe from BIOS... Linux video capture interface: v2.00 +PCI: Enabling device 0000:00:1f.3 (0001 -> 0003) +ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18 logips2pp: Detected unknown logitech mouse model 95 saa7146: register extension 'dvb'. ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 22 -saa7146: found saa7146 @ mem ffffc2000039c800 (revision 1, irq 22) (0x13c2,0x0003). -DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X). -ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 -PCI: Setting latency timer of device 0000:00:1b.0 to 64 +saa7146: found saa7146 @ mem ffffc20000ace800 (revision 1, irq 22) (0x13c2,0x0003). +DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X) adapter has MAC addr = 00:d0:5c:22:68:cc dvb-ttpci: gpioirq unknown type=0 len=0 dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622 dvb-ttpci: firmware @ card 0 supports CI link layer interface -hda_codec: Unknown model for AD1988, trying auto-probe from BIOS... -input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 +input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4 dvb-ttpci: adac type set to 0 @ card 0 saa7146_vv: saa7146 (0): registered device video0 [v4l2] saa7146_vv: saa7146 (0): registered device vbi0 [v4l2] DVB: registering frontend 0 (ST STV0299 DVB-S)... -input: DVB on-card IR receiver as /class/input/input3 +input: DVB on-card IR receiver as /class/input/input5 dvb-ttpci: found av7110-0. EXT3 FS on sda6, internal journal device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com @@ -452,23 +466,16 @@ EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended -EXT3 FS on hdf10, internal journal +EXT3 FS on sda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. -skge eth0: enabling interface -skge eth0: Link is up at 1000 Mbps, full duplex, flow control both NET: Registered protocol family 10 lo: Disabled Privacy Extensions -input: Power Button (FF) as /class/input/input4 -ACPI: Power Button (FF) [PWRF] -input: Power Button (CM) as /class/input/input5 -ACPI: Power Button (CM) [PWRB] pnp: the driver 'parport_pc' has been registered lp: driver loaded but no devices found ppdev: user-space parallel port driver -eth0: no IPv6 routers present [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 -[drm] Initialized radeon 1.25.0 20060524 on minor 0 +[drm] Initialized radeon 1.28.0 20060524 on minor 0 [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs