Message-ID: <47867383.9010309@yahoo.de>
Date:	Thu, 10 Jan 2008 20:35:31 +0100
From:	supersud501 <supersud501@...oo.de>
To:	Stephen Hemminger <shemminger@...ux-foundation.org>
CC:	Andrew Morton <akpm@...ux-foundation.org>, netdev@...r.kernel.org,
	linux-acpi@...r.kernel.org
Subject: Re: [Bugme-new] [Bug 9721] New: wake on lan fails with sky2 module



Stephen Hemminger schrieb:
> On Wed, 9 Jan 2008 16:03:00 -0800
> Andrew Morton <akpm@...ux-foundation.org> wrote:
> 
>> (switched to email.  Please respond via emailed reply-to-all, not via the
>> bugzilla web interface).
>>
>> On Wed,  9 Jan 2008 13:05:34 -0800 (PST)
>> bugme-daemon@...zilla.kernel.org wrote:
>>
>>> http://bugzilla.kernel.org/show_bug.cgi?id=9721
>>>
>>>            Summary: wake on lan fails with sky2 module
>>>            Product: ACPI
>>>            Version: 2.5
>>>      KernelVersion: 2.6.24-rc7
>>>           Platform: All
>>>         OS/Version: Linux
>>>               Tree: Mainline
>>>             Status: NEW
>>>           Severity: normal
>>>           Priority: P1
>>>          Component: Power-Sleep-Wake
>>>         AssignedTo: acpi_power-sleep-wake@...nel-bugs.osdl.org
>>>         ReportedBy: supersud501@...oo.de
>> This post-2.6.23 regression was assigned to ACPI but is quite possibly a
>> net driver problem?
>>
>>> Latest working kernel version: 2.6.23.12
>>> Earliest failing kernel version: 2.6.24-rc6 (not tested earlier kernel,
>>> 2.6.24-rc7 still failing)
>>> Distribution: Ubuntu 8.04 (but Kernel build from Kernel.org and system modifiet
>>> to make wake on lan work, i.e. network cards are not shutted down on poweroff)
>>> Hardware Environment: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit
>>> Ethernet Controller (rev 20) onboard Asus P5W DH motherboard, uses module SKY2
>>> Software Environment:
>>> Problem Description:
>>>
>>> When enabling wake on lan with: 'ethtool -s eth0 wol' i get the following
>>> status:
>>>
>>> 21:56:29 ~ # sudo ethtool eth0
>>> Settings for eth0:
>>>         Supported ports: [ TP ]
>>>         Supported link modes:   10baseT/Half 10baseT/Full 
>>>                                 100baseT/Half 100baseT/Full 
>>>                                 1000baseT/Half 1000baseT/Full 
>>>         Supports auto-negotiation: Yes
>>>         Advertised link modes:  10baseT/Half 10baseT/Full 
>>>                                 100baseT/Half 100baseT/Full 
>>>                                 1000baseT/Half 1000baseT/Full 
>>>         Advertised auto-negotiation: Yes
>>>         Speed: 100Mb/s
>>>         Duplex: Full
>>>         Port: Twisted Pair
>>>         PHYAD: 0
>>>         Transceiver: internal
>>>         Auto-negotiation: on
>>>         Supports Wake-on: pg
>>>         Wake-on: g    <---- wol enabled
>>>         Current message level: 0x000000ff (255)
>>>         Link detected: yes
>>>
>>> but after shutting down the pc doesn't wake up when magic packet is sent.
>>>
>>> the status lights of the network card are still on (so the card seems to be
>>> online).
>>>
>>> same system with only changed kernel to 2.6.23.12 and same procedure like
>>> above: wake on lan works.
>>>
>>> Steps to reproduce: enable wol on your network card using SKY2 module and it
>>> doesn't work too?
>>>
>>> if you need more information, just tell me, it's my first bug report.
>>> regards
>>>
> 
> 
> Wake from power off works on 2.6.24-rc7 for me.
> Wake from suspend doesn't because Network Manager, HAL, or some other
> user space tool gets confused.
> 
> I just rechecked it with Fujitsu Lifebook, which has sky2 (88E8055).
> There many variations of this chip, and it maybe chip specific problem
> or ACPI/BIOS issues.  If you don't enable Wake on Lan in BIOS, the
> driver can't do it for you. Also, check how you are shutting down.
> 
> Also since the device has to restart the PHY, it could be a switch
> issue if you have some fancy pants switch doing intrusion detection
> or something, but I doubt that.
> 
> Is it a clean or fast shutdown, most distributions mark network
> devices as down on shutdown, but if the distribution does something 
> stupid like remove the driver module, then the driver is unable to setup Wake On Lan.
> The wake on lan setup is done in one place in the driver, add
> a printk to see if it is ever called.
> 
> 

I only tried wake from shutdown (poweroff), and like i wrote, on the 
same system with kernel 2.6.23.12 (nothing changed but vmlinuz and 
initrd, with the same kernel config on 2.6.24-rc6/7 (make oldconfig, 
default answer to all questions)), it works. so it seems to me like a 
problem in the kernel.

every wake-up setting (wake up by pci-device, rtc-alarm, modem ...) in 
bios is also enabled, otherwise it couldn't work in 2.6.23.12 (and windows).

if you say your sky2-card works, it might be a acpi-problem not related 
to sky2 like i thought - when i am at home i'll try to start my pc with 
a timer (--> /proc/acpi/alarm) from kernel 2.6.24-rc7 to check if 
acpi-wakeup works and report back (if it is any help in finding the 
source of my problem).

and regarding "printk" i'll try to find out what you mean (my first 
steps into kernel debugging :) - i think you mean adding a line in the 
source to print out something when the function is called)

regards
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists