| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <482397D3.7090300@myri.com>
Date: Fri, 09 May 2008 02:16:19 +0200
From: Brice Goglin <brice@...i.com>
To: Jeff Garzik <jeff@...zik.org>
CC: netdev@...r.kernel.org
Subject: [PATCH 01/16] myri10ge: update firmware headers
Update myri10ge firmware headers.
Signed-off-by: Brice Goglin <brice@...i.com>
Signed-off-by: Andrew Gallatin <gallatin@...i.com>
---
drivers/net/myri10ge/myri10ge_mcp.h | 56 ++++++++++++++++++++++---
drivers/net/myri10ge/myri10ge_mcp_gen_header.h | 39 ++++++-----------
2 files changed, 64 insertions(+), 31 deletions(-)
Index: linux-2.6/drivers/net/myri10ge/myri10ge_mcp.h
===================================================================
--- linux-2.6.orig/drivers/net/myri10ge/myri10ge_mcp.h 2008-05-08 23:59:52.000000000 +0200
+++ linux-2.6/drivers/net/myri10ge/myri10ge_mcp.h 2008-05-09 00:00:00.000000000 +0200
@@ -10,7 +10,7 @@
__be32 low;
};
-/* 4 Bytes. 8 Bytes for NDIS drivers. */
+/* 4 Bytes */
struct mcp_slot {
__sum16 checksum;
__be16 length;
@@ -144,6 +144,7 @@
* a power of 2 number of entries. */
MXGEFW_CMD_SET_INTRQ_SIZE, /* in bytes */
+#define MXGEFW_CMD_SET_INTRQ_SIZE_FLAG_NO_STRICT_SIZE_CHECK (1 << 31)
/* command to bring ethernet interface up. Above parameters
* (plus mtu & mac address) must have been exchanged prior
@@ -221,10 +222,14 @@
MXGEFW_CMD_GET_MAX_RSS_QUEUES,
MXGEFW_CMD_ENABLE_RSS_QUEUES,
/* data0 = number of slices n (0, 1, ..., n-1) to enable
- * data1 = interrupt mode. 0=share one INTx/MSI, 1=use one MSI-X per queue.
+ * data1 = interrupt mode.
+ * 0=share one INTx/MSI, 1=use one MSI-X per queue.
* If all queues share one interrupt, the driver must have set
* RSS_SHARED_INTERRUPT_DMA before enabling queues.
*/
+#define MXGEFW_SLICE_INTR_MODE_SHARED 0
+#define MXGEFW_SLICE_INTR_MODE_ONE_PER_SLICE 1
+
MXGEFW_CMD_GET_RSS_SHARED_INTERRUPT_MASK_OFFSET,
MXGEFW_CMD_SET_RSS_SHARED_INTERRUPT_DMA,
/* data0, data1 = bus address lsw, msw */
@@ -241,10 +246,14 @@
* 0: disable rss. nic does not distribute receive packets.
* 1: enable rss. nic distributes receive packets among queues.
* data1 = hash type
- * 1: IPV4
- * 2: TCP_IPV4
- * 3: IPV4 | TCP_IPV4
+ * 1: IPV4 (required by RSS)
+ * 2: TCP_IPV4 (required by RSS)
+ * 3: IPV4 | TCP_IPV4 (required by RSS)
+ * 4: source port
*/
+#define MXGEFW_RSS_HASH_TYPE_IPV4 0x1
+#define MXGEFW_RSS_HASH_TYPE_TCP_IPV4 0x2
+#define MXGEFW_RSS_HASH_TYPE_SRC_PORT 0x4
MXGEFW_CMD_GET_MAX_TSO6_HDR_SIZE,
/* Return data = the max. size of the entire headers of a IPv6 TSO packet.
@@ -260,6 +269,8 @@
* 0: Linux/FreeBSD style (NIC default)
* 1: NDIS/NetBSD style
*/
+#define MXGEFW_TSO_MODE_LINUX 0
+#define MXGEFW_TSO_MODE_NDIS 1
MXGEFW_CMD_MDIO_READ,
/* data0 = dev_addr (PMA/PMD or PCS ...), data1 = register/addr */
@@ -286,6 +297,38 @@
/* Return data = NIC memory offset of mcp_vpump_public_global */
MXGEFW_CMD_RESET_VPUMP,
/* Resets the VPUMP state */
+
+ MXGEFW_CMD_SET_RSS_MCP_SLOT_TYPE,
+ /* data0 = mcp_slot type to use.
+ * 0 = the default 4B mcp_slot
+ * 1 = 8B mcp_slot_8
+ */
+#define MXGEFW_RSS_MCP_SLOT_TYPE_MIN 0
+#define MXGEFW_RSS_MCP_SLOT_TYPE_WITH_HASH 1
+
+ MXGEFW_CMD_SET_THROTTLE_FACTOR,
+ /* set the throttle factor for ethp_z8e
+ * data0 = throttle_factor
+ * throttle_factor = 256 * pcie-raw-speed / tx_speed
+ * tx_speed = 256 * pcie-raw-speed / throttle_factor
+ *
+ * For PCI-E x8: pcie-raw-speed == 16Gb/s
+ * For PCI-E x4: pcie-raw-speed == 8Gb/s
+ *
+ * ex1: throttle_factor == 0x1a0 (416), tx_speed == 1.23GB/s == 9.846 Gb/s
+ * ex2: throttle_factor == 0x200 (512), tx_speed == 1.0GB/s == 8 Gb/s
+ *
+ * with tx_boundary == 2048, max-throttle-factor == 8191 => min-speed == 500Mb/s
+ * with tx_boundary == 4096, max-throttle-factor == 4095 => min-speed == 1Gb/s
+ */
+
+ MXGEFW_CMD_VPUMP_UP,
+ /* Allocates VPump Connection, Send Request and Zero copy buffer address tables */
+ MXGEFW_CMD_GET_VPUMP_CLK,
+ /* Get the lanai clock */
+
+ MXGEFW_CMD_GET_DCA_OFFSET,
+ /* offset of dca control for WDMAs */
};
enum myri10ge_mcp_cmd_status {
@@ -302,7 +345,8 @@
MXGEFW_CMD_ERROR_UNALIGNED,
MXGEFW_CMD_ERROR_NO_MDIO,
MXGEFW_CMD_ERROR_XFP_FAILURE,
- MXGEFW_CMD_ERROR_XFP_ABSENT
+ MXGEFW_CMD_ERROR_XFP_ABSENT,
+ MXGEFW_CMD_ERROR_BAD_PCIE_LINK
};
#define MXGEFW_OLD_IRQ_DATA_LEN 40
Index: linux-2.6/drivers/net/myri10ge/myri10ge_mcp_gen_header.h
===================================================================
--- linux-2.6.orig/drivers/net/myri10ge/myri10ge_mcp_gen_header.h 2008-05-08 23:59:52.000000000 +0200
+++ linux-2.6/drivers/net/myri10ge/myri10ge_mcp_gen_header.h 2008-05-09 00:00:00.000000000 +0200
@@ -1,30 +1,6 @@
#ifndef __MYRI10GE_MCP_GEN_HEADER_H__
#define __MYRI10GE_MCP_GEN_HEADER_H__
-/* this file define a standard header used as a first entry point to
- * exchange information between firmware/driver and driver. The
- * header structure can be anywhere in the mcp. It will usually be in
- * the .data section, because some fields needs to be initialized at
- * compile time.
- * The 32bit word at offset MX_HEADER_PTR_OFFSET in the mcp must
- * contains the location of the header.
- *
- * Typically a MCP will start with the following:
- * .text
- * .space 52 ! to help catch MEMORY_INT errors
- * bt start ! jump to real code
- * nop
- * .long _gen_mcp_header
- *
- * The source will have a definition like:
- *
- * mcp_gen_header_t gen_mcp_header = {
- * .header_length = sizeof(mcp_gen_header_t),
- * .mcp_type = MCP_TYPE_XXX,
- * .version = "something $Id: mcp_gen_header.h,v 1.2 2006/05/13 10:04:35 bgoglin Exp $",
- * .mcp_globals = (unsigned)&Globals
- * };
- */
#define MCP_HEADER_PTR_OFFSET 0x3c
@@ -32,13 +8,14 @@
#define MCP_TYPE_PCIE 0x70636965 /* "PCIE" pcie-only MCP */
#define MCP_TYPE_ETH 0x45544820 /* "ETH " */
#define MCP_TYPE_MCP0 0x4d435030 /* "MCP0" */
+#define MCP_TYPE_DFLT 0x20202020 /* " " */
struct mcp_gen_header {
/* the first 4 fields are filled at compile time */
unsigned header_length;
__be32 mcp_type;
char version[128];
- unsigned mcp_globals; /* pointer to mcp-type specific structure */
+ unsigned mcp_private; /* pointer to mcp-type specific structure */
/* filled by the MCP at run-time */
unsigned sram_size;
@@ -53,6 +30,18 @@
*
* Never remove any field. Keep everything naturally align.
*/
+
+ /* Specifies if the running mcp is mcp0, 1, or 2. */
+ unsigned char mcp_index;
+ unsigned char disable_rabbit;
+ unsigned char unaligned_tlp;
+ unsigned char pad1;
+ unsigned counters_addr;
+ unsigned copy_block_info; /* for small mcps loaded with "lload -d" */
+ unsigned short handoff_id_major; /* must be equal */
+ unsigned short handoff_id_caps; /* bitfield: new mcp must have superset */
+ unsigned msix_table_addr; /* start address of msix table in firmware */
+ /* 8 */
};
#endif /* __MYRI10GE_MCP_GEN_HEADER_H__ */
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists