| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1218636796.547.80.camel@lb-tlvb-eliezer>
Date: Wed, 13 Aug 2008 17:13:16 +0300
From: "Eilon Greenstein" <eilong@...adcom.com>
To: "David Miller" <davem@...emloft.net>,
netdev <netdev@...r.kernel.org>
cc: "Vladislav Zolotarov" <vladz@...adcom.com>
Subject: [PATCH 05/25] bnx2x: Load/Unload under traffic
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@...adcom.com>
Signed-off-by: Eilon Greenstein <eilong@...adcom.com>
---
drivers/net/bnx2x.h | 9 ++
drivers/net/bnx2x_main.c | 221 +++++++++++++++++++++++++--------------------
drivers/net/bnx2x_reg.h | 3 +
3 files changed, 135 insertions(+), 98 deletions(-)
diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h
index 9cbf0e8..b9aa6f4 100644
--- a/drivers/net/bnx2x.h
+++ b/drivers/net/bnx2x.h
@@ -274,6 +274,15 @@ struct bnx2x_fastpath {
#define bnx2x_fp(bp, nr, var) (bp->fp[nr].var)
+#define BNX2X_HAS_TX_WORK(fp) \
+ ((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || \
+ (fp->tx_pkt_prod != fp->tx_pkt_cons))
+
+#define BNX2X_HAS_RX_WORK(fp) \
+ (fp->rx_comp_cons != le16_to_cpu(*fp->rx_cons_sb))
+
+#define BNX2X_HAS_WORK(fp) (BNX2X_HAS_RX_WORK(fp) || BNX2X_HAS_TX_WORK(fp))
+
/* MC hsi */
#define MAX_FETCH_BD 13 /* HW max BDs per packet */
diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c
index 6115161..dfa8c7b 100755
--- a/drivers/net/bnx2x_main.c
+++ b/drivers/net/bnx2x_main.c
@@ -717,21 +717,6 @@ static inline u16 bnx2x_update_fpsb_idx(struct bnx2x_fastpath *fp)
return rc;
}
-static inline int bnx2x_has_work(struct bnx2x_fastpath *fp)
-{
- u16 rx_cons_sb = le16_to_cpu(*fp->rx_cons_sb);
-
- if ((rx_cons_sb & MAX_RCQ_DESC_CNT) == MAX_RCQ_DESC_CNT)
- rx_cons_sb++;
-
- if ((fp->rx_comp_cons != rx_cons_sb) ||
- (fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) ||
- (fp->tx_pkt_prod != fp->tx_pkt_cons))
- return 1;
-
- return 0;
-}
-
static u16 bnx2x_ack_int(struct bnx2x *bp)
{
u32 igu_addr = (IGU_ADDR_SIMD_MASK + IGU_FUNC_BASE * BP_FUNC(bp)) * 8;
@@ -899,6 +884,7 @@ static void bnx2x_tx_int(struct bnx2x_fastpath *fp, int work)
netif_tx_lock(bp->dev);
if (netif_queue_stopped(bp->dev) &&
+ (bp->state == BNX2X_STATE_OPEN) &&
(bnx2x_tx_avail(fp) >= MAX_SKB_FRAGS + 3))
netif_wake_queue(bp->dev);
@@ -1617,6 +1603,12 @@ static irqreturn_t bnx2x_msix_fp_int(int irq, void *fp_cookie)
struct net_device *dev = bp->dev;
int index = FP_IDX(fp);
+ /* Return here if interrupt is disabled */
+ if (unlikely(atomic_read(&bp->intr_sem) != 0)) {
+ DP(NETIF_MSG_INTR, "called but intr_sem not 0, returning\n");
+ return IRQ_HANDLED;
+ }
+
DP(BNX2X_MSG_FP, "got an MSI-X interrupt on IDX:SB [%d:%d]\n",
index, FP_SB_ID(fp));
bnx2x_ack_sb(bp, FP_SB_ID(fp), USTORM_ID, 0, IGU_INT_DISABLE, 0);
@@ -6230,22 +6222,24 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
if (!BP_NOMCP(bp)) {
load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_REQ);
if (!load_code) {
- BNX2X_ERR("MCP response failure, unloading\n");
+ BNX2X_ERR("MCP response failure, aborting\n");
return -EBUSY;
}
if (load_code == FW_MSG_CODE_DRV_LOAD_REFUSED)
return -EBUSY; /* other port in diagnostic mode */
} else {
+ int port = BP_PORT(bp);
+
DP(NETIF_MSG_IFUP, "NO MCP load counts before us %d, %d, %d\n",
load_count[0], load_count[1], load_count[2]);
load_count[0]++;
- load_count[1 + BP_PORT(bp)]++;
+ load_count[1 + port]++;
DP(NETIF_MSG_IFUP, "NO MCP new load counts %d, %d, %d\n",
load_count[0], load_count[1], load_count[2]);
if (load_count[0] == 1)
load_code = FW_MSG_CODE_DRV_LOAD_COMMON;
- else if (load_count[1 + BP_PORT(bp)] == 1)
+ else if (load_count[1 + port] == 1)
load_code = FW_MSG_CODE_DRV_LOAD_PORT;
else
load_code = FW_MSG_CODE_DRV_LOAD_FUNCTION;
@@ -6294,9 +6288,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
bnx2x_fp(bp, i, disable_tpa) =
((bp->flags & TPA_ENABLE_FLAG) == 0);
- /* Disable interrupt handling until HW is initialized */
- atomic_set(&bp->intr_sem, 1);
-
if (bp->flags & USING_MSIX_FLAG) {
rc = bnx2x_req_msix_irqs(bp);
if (rc) {
@@ -6323,9 +6314,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
goto load_error;
}
- /* Enable interrupt handling */
- atomic_set(&bp->intr_sem, 0);
-
/* Setup NIC internals and enable interrupts */
bnx2x_nic_init(bp, load_code);
@@ -6333,7 +6321,7 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
if (!BP_NOMCP(bp)) {
load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_DONE);
if (!load_code) {
- BNX2X_ERR("MCP response failure, unloading\n");
+ BNX2X_ERR("MCP response failure, aborting\n");
rc = -EBUSY;
goto load_int_disable;
}
@@ -6348,11 +6336,12 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
for_each_queue(bp, i)
napi_enable(&bnx2x_fp(bp, i, napi));
+ /* Enable interrupt handling */
+ atomic_set(&bp->intr_sem, 0);
+
rc = bnx2x_setup_leading(bp);
if (rc) {
-#ifdef BNX2X_STOP_ON_ERROR
- bp->panic = 1;
-#endif
+ BNX2X_ERR("Setup leading failed!\n");
goto load_stop_netif;
}
@@ -6386,7 +6375,6 @@ static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
break;
case LOAD_OPEN:
- /* IRQ is only requested from bnx2x_open */
netif_start_queue(bp->dev);
bnx2x_set_rx_mode(bp->dev);
if (bp->flags & USING_MSIX_FLAG)
@@ -6458,7 +6446,7 @@ static int bnx2x_stop_multi(struct bnx2x *bp, int index)
return rc;
}
-static void bnx2x_stop_leading(struct bnx2x *bp)
+static int bnx2x_stop_leading(struct bnx2x *bp)
{
u16 dsb_sp_prod_idx;
/* if the other port is handling traffic,
@@ -6476,7 +6464,7 @@ static void bnx2x_stop_leading(struct bnx2x *bp)
rc = bnx2x_wait_ramrod(bp, BNX2X_FP_STATE_HALTED, 0,
&(bp->fp[0].state), 1);
if (rc) /* timeout */
- return;
+ return rc;
dsb_sp_prod_idx = *bp->dsb_sp_prod;
@@ -6495,13 +6483,18 @@ static void bnx2x_stop_leading(struct bnx2x *bp)
*bp->dsb_sp_prod, dsb_sp_prod_idx);
#ifdef BNX2X_STOP_ON_ERROR
bnx2x_panic();
+#else
+ rc = -EBUSY;
#endif
break;
}
cnt--;
+ msleep(1);
}
bp->state = BNX2X_STATE_CLOSING_WAIT4_UNLOAD;
bp->fp[0].state = BNX2X_FP_STATE_CLOSED;
+
+ return rc;
}
static void bnx2x_reset_func(struct bnx2x *bp)
@@ -6586,8 +6579,9 @@ static void bnx2x_reset_chip(struct bnx2x *bp, u32 reset_code)
/* msut be called with rtnl_lock */
static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode)
{
+ int port = BP_PORT(bp);
u32 reset_code = 0;
- int i, cnt;
+ int i, cnt, rc;
bp->state = BNX2X_STATE_CLOSING_WAIT4_HALT;
@@ -6604,22 +6598,17 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode)
(DRV_PULSE_ALWAYS_ALIVE | bp->fw_drv_pulse_wr_seq));
bnx2x_stats_handle(bp, STATS_EVENT_STOP);
- /* Wait until all fast path tasks complete */
+ /* Wait until tx fast path tasks complete */
for_each_queue(bp, i) {
struct bnx2x_fastpath *fp = &bp->fp[i];
-#ifdef BNX2X_STOP_ON_ERROR
-#ifdef __powerpc64__
- DP(NETIF_MSG_RX_STATUS, "fp->tpa_queue_used = 0x%lx\n",
-#else
- DP(NETIF_MSG_IFDOWN, "fp->tpa_queue_used = 0x%llx\n",
-#endif
- fp->tpa_queue_used);
-#endif
cnt = 1000;
smp_rmb();
- while (bnx2x_has_work(fp)) {
- msleep(1);
+ while (BNX2X_HAS_TX_WORK(fp)) {
+
+ if (!netif_running(bp->dev))
+ bnx2x_tx_int(fp, 1000);
+
if (!cnt) {
BNX2X_ERR("timeout waiting for queue[%d]\n",
i);
@@ -6631,14 +6620,13 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode)
#endif
}
cnt--;
+ msleep(1);
smp_rmb();
}
}
- /* Wait until all slow path tasks complete */
- cnt = 1000;
- while ((bp->spq_left != MAX_SPQ_PENDING) && cnt--)
- msleep(1);
+ /* Give HW time to discard old tx messages */
+ msleep(1);
for_each_queue(bp, i)
napi_disable(&bnx2x_fp(bp, i, napi));
@@ -6648,52 +6636,51 @@ static int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode)
/* Release IRQs */
bnx2x_free_irq(bp);
- if (bp->flags & NO_WOL_FLAG)
+ if (unload_mode == UNLOAD_NORMAL)
+ reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
+
+ else if (bp->flags & NO_WOL_FLAG) {
reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_MCP;
+ if (CHIP_IS_E1H(bp))
+ REG_WR(bp, MISC_REG_E1HMF_MODE, 0);
- else if (bp->wol) {
- u32 emac_base = BP_PORT(bp) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ } else if (bp->wol) {
+ u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
u8 *mac_addr = bp->dev->dev_addr;
u32 val;
-
/* The mac address is written to entries 1-4 to
preserve entry 0 which is used by the PMF */
+ u8 entry = (BP_E1HVN(bp) + 1)*8;
+
val = (mac_addr[0] << 8) | mac_addr[1];
- EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + (BP_E1HVN(bp) + 1)*8, val);
+ EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry, val);
val = (mac_addr[2] << 24) | (mac_addr[3] << 16) |
(mac_addr[4] << 8) | mac_addr[5];
- EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + (BP_E1HVN(bp) + 1)*8 + 4,
- val);
+ EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + entry + 4, val);
reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_EN;
} else
reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
+ if (CHIP_IS_E1H(bp))
+ REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 0);
+
/* Close multi and leading connections
Completions for ramrods are collected in a synchronous way */
for_each_nondefault_queue(bp, i)
if (bnx2x_stop_multi(bp, i))
goto unload_error;
- if (CHIP_IS_E1H(bp))
- REG_WR(bp, NIG_REG_LLH0_FUNC_EN + BP_PORT(bp)*8, 0);
-
- bnx2x_stop_leading(bp);
-#ifdef BNX2X_STOP_ON_ERROR
- /* If ramrod completion timed out - break here! */
- if (bp->panic) {
+ rc = bnx2x_stop_leading(bp);
+ if (rc) {
BNX2X_ERR("Stop leading failed!\n");
+#ifdef BNX2X_STOP_ON_ERROR
return -EBUSY;
- }
+#else
+ goto unload_error;
#endif
-
- if ((bp->state != BNX2X_STATE_CLOSING_WAIT4_UNLOAD) ||
- (bp->fp[0].state != BNX2X_FP_STATE_CLOSED)) {
- DP(NETIF_MSG_IFDOWN, "failed to close leading properly! "
- "state 0x%x fp[0].state 0x%x\n",
- bp->state, bp->fp[0].state);
}
unload_error:
@@ -6703,12 +6690,12 @@ unload_error:
DP(NETIF_MSG_IFDOWN, "NO MCP load counts %d, %d, %d\n",
load_count[0], load_count[1], load_count[2]);
load_count[0]--;
- load_count[1 + BP_PORT(bp)]--;
+ load_count[1 + port]--;
DP(NETIF_MSG_IFDOWN, "NO MCP new load counts %d, %d, %d\n",
load_count[0], load_count[1], load_count[2]);
if (load_count[0] == 0)
reset_code = FW_MSG_CODE_DRV_UNLOAD_COMMON;
- else if (load_count[1 + BP_PORT(bp)] == 0)
+ else if (load_count[1 + port] == 0)
reset_code = FW_MSG_CODE_DRV_UNLOAD_PORT;
else
reset_code = FW_MSG_CODE_DRV_UNLOAD_FUNCTION;
@@ -6780,50 +6767,86 @@ static void __devinit bnx2x_undi_unload(struct bnx2x *bp)
/* Check if it is the UNDI driver
* UNDI driver initializes CID offset for normal bell to 0x7
*/
+ bnx2x_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
val = REG_RD(bp, DORQ_REG_NORM_CID_OFST);
if (val == 0x7) {
u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
- /* save our func and fw_seq */
+ /* save our func */
int func = BP_FUNC(bp);
- u16 fw_seq = bp->fw_seq;
+ u32 swap_en;
+ u32 swap_val;
BNX2X_DEV_INFO("UNDI is active! reset device\n");
/* try unload UNDI on port 0 */
bp->func = 0;
- bp->fw_seq = (SHMEM_RD(bp,
- func_mb[bp->func].drv_mb_header) &
- DRV_MSG_SEQ_NUMBER_MASK);
-
+ bp->fw_seq =
+ (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) &
+ DRV_MSG_SEQ_NUMBER_MASK);
reset_code = bnx2x_fw_command(bp, reset_code);
- bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE);
/* if UNDI is loaded on the other port */
if (reset_code != FW_MSG_CODE_DRV_UNLOAD_COMMON) {
+ /* send "DONE" for previous unload */
+ bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE);
+
+ /* unload UNDI on port 1 */
bp->func = 1;
- bp->fw_seq = (SHMEM_RD(bp,
- func_mb[bp->func].drv_mb_header) &
- DRV_MSG_SEQ_NUMBER_MASK);
-
- bnx2x_fw_command(bp,
- DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS);
- bnx2x_fw_command(bp,
- DRV_MSG_CODE_UNLOAD_DONE);
-
- /* restore our func and fw_seq */
- bp->func = func;
- bp->fw_seq = fw_seq;
+ bp->fw_seq =
+ (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) &
+ DRV_MSG_SEQ_NUMBER_MASK);
+ reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
+
+ bnx2x_fw_command(bp, reset_code);
}
+ REG_WR(bp, (BP_PORT(bp) ? HC_REG_CONFIG_1 :
+ HC_REG_CONFIG_0), 0x1000);
+
+ /* close input traffic and wait for it */
+ /* Do not rcv packets to BRB */
+ REG_WR(bp,
+ (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_DRV_MASK :
+ NIG_REG_LLH0_BRB1_DRV_MASK), 0x0);
+ /* Do not direct rcv packets that are not for MCP to
+ * the BRB */
+ REG_WR(bp,
+ (BP_PORT(bp) ? NIG_REG_LLH1_BRB1_NOT_MCP :
+ NIG_REG_LLH0_BRB1_NOT_MCP), 0x0);
+ /* clear AEU */
+ REG_WR(bp,
+ (BP_PORT(bp) ? MISC_REG_AEU_MASK_ATTN_FUNC_1 :
+ MISC_REG_AEU_MASK_ATTN_FUNC_0), 0);
+ msleep(10);
+
+ /* save NIG port swap info */
+ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+ swap_en = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
/* reset device */
REG_WR(bp,
GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR,
- 0xd3ffff7f);
+ 0xd3ffffff);
REG_WR(bp,
GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
0x1403);
+ /* take the NIG out of reset and restore swap values */
+ REG_WR(bp,
+ GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET,
+ MISC_REGISTERS_RESET_REG_1_RST_NIG);
+ REG_WR(bp, NIG_REG_PORT_SWAP, swap_val);
+ REG_WR(bp, NIG_REG_STRAP_OVERRIDE, swap_en);
+
+ /* send unload done to the MCP */
+ bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE);
+
+ /* restore our func and fw_seq */
+ bp->func = func;
+ bp->fw_seq =
+ (SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) &
+ DRV_MSG_SEQ_NUMBER_MASK);
}
+ bnx2x_hw_unlock(bp, HW_LOCK_RESOURCE_UNDI);
}
}
@@ -7384,6 +7407,9 @@ static int __devinit bnx2x_init_bp(struct bnx2x *bp)
int func = BP_FUNC(bp);
int rc;
+ /* Disable interrupt handling until HW is initialized */
+ atomic_set(&bp->intr_sem, 1);
+
mutex_init(&bp->port.phy_mutex);
INIT_WORK(&bp->sp_task, bnx2x_sp_task);
@@ -9163,17 +9189,16 @@ static int bnx2x_poll(struct napi_struct *napi, int budget)
bnx2x_update_fpsb_idx(fp);
- if ((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) ||
- (fp->tx_pkt_prod != fp->tx_pkt_cons))
+ if (BNX2X_HAS_TX_WORK(fp))
bnx2x_tx_int(fp, budget);
- if (le16_to_cpu(*fp->rx_cons_sb) != fp->rx_comp_cons)
+ if (BNX2X_HAS_RX_WORK(fp))
work_done = bnx2x_rx_int(fp, budget);
- rmb(); /* bnx2x_has_work() reads the status block */
+ rmb(); /* BNX2X_HAS_WORK() reads the status block */
/* must not complete if we consumed full budget */
- if ((work_done < budget) && !bnx2x_has_work(fp)) {
+ if ((work_done < budget) && !BNX2X_HAS_WORK(fp)) {
#ifdef BNX2X_STOP_ON_ERROR
poll_panic:
@@ -9408,7 +9433,7 @@ static int bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev)
DP(NETIF_MSG_TX_QUEUED, "SKB linearization failed - "
"silently dropping this SKB\n");
dev_kfree_skb_any(skb);
- return 0;
+ return NETDEV_TX_OK;
}
}
@@ -10200,7 +10225,7 @@ static int bnx2x_suspend(struct pci_dev *pdev, pm_message_t state)
netif_device_detach(dev);
- bnx2x_nic_unload(bp, UNLOAD_NORMAL);
+ bnx2x_nic_unload(bp, UNLOAD_CLOSE);
bnx2x_set_power_state(bp, pci_choose_state(pdev, state));
@@ -10233,7 +10258,7 @@ static int bnx2x_resume(struct pci_dev *pdev)
bnx2x_set_power_state(bp, PCI_D0);
netif_device_attach(dev);
- rc = bnx2x_nic_load(bp, LOAD_NORMAL);
+ rc = bnx2x_nic_load(bp, LOAD_OPEN);
rtnl_unlock();
diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h
index 40c3a77..b5313c2 100644
--- a/drivers/net/bnx2x_reg.h
+++ b/drivers/net/bnx2x_reg.h
@@ -1677,6 +1677,7 @@
/* [RW 8] init credit counter for port0 in LLH */
#define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554
#define NIG_REG_LLH0_XCM_MASK 0x10130
+#define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248
/* [RW 1] send to BRB1 if no match on any of RMP rules. */
#define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc
/* [RW 2] Determine the classification participants. 0: no classification.1:
@@ -4962,6 +4963,7 @@
#define MISC_REGISTERS_GPIO_PORT_SHIFT 4
#define MISC_REGISTERS_GPIO_SET_POS 8
#define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7)
#define MISC_REGISTERS_RESET_REG_1_SET 0x584
#define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598
#define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0)
@@ -4997,6 +4999,7 @@
#define HW_LOCK_RESOURCE_8072_MDIO 0
#define HW_LOCK_RESOURCE_GPIO 1
#define HW_LOCK_RESOURCE_SPIO 2
+#define HW_LOCK_RESOURCE_UNDI 5
#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18)
#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31)
#define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9)
--
1.5.3.2
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists