| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1223920114-19788-8-git-send-email-linux@dominikbrodowski.net>
Date: Mon, 13 Oct 2008 19:47:53 +0200
From: Dominik Brodowski <linux@...inikbrodowski.net>
To: <linux-pcmcia@...ts.infradead.org>
Cc: Dominik Brodowski <linux@...inikbrodowski.net>,
netdev@...r.kernel.org
Subject: [PATCH 08/49] pcmcia: use pcmcia_loop_config in net pcmcia drivers
Use the config loop helper in (some) net pcmcia drivers.
CC: netdev@...r.kernel.org
Signed-off-by: Dominik Brodowski <linux@...inikbrodowski.net>
---
drivers/net/pcmcia/axnet_cs.c | 71 ++++------
drivers/net/pcmcia/pcnet_cs.c | 79 +++++------
drivers/net/pcmcia/smc91c92_cs.c | 96 +++++---------
drivers/net/pcmcia/xirc2ps_cs.c | 73 ++++++----
drivers/net/wireless/airo_cs.c | 230 ++++++++++++++++---------------
drivers/net/wireless/atmel_cs.c | 123 ++++++++---------
drivers/net/wireless/hostap/hostap_cs.c | 227 +++++++++++++++----------------
drivers/net/wireless/orinoco_cs.c | 176 ++++++++++++------------
drivers/net/wireless/spectrum_cs.c | 175 ++++++++++++------------
9 files changed, 596 insertions(+), 654 deletions(-)
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index 3f682d4..04ece0b 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -284,58 +284,47 @@ static int try_io_port(struct pcmcia_device *link)
}
}
+static int axnet_configcheck(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ int i;
+ cistpl_io_t *io = &cfg->io;
+
+ if (cfg->index == 0 || cfg->io.nwin == 0)
+ return -ENODEV;
+
+ p_dev->conf.ConfigIndex = 0x05;
+ /* For multifunction cards, by convention, we configure the
+ network function with window 0, and serial with window 1 */
+ if (io->nwin > 1) {
+ i = (io->win[1].len > io->win[0].len);
+ p_dev->io.BasePort2 = io->win[1-i].base;
+ p_dev->io.NumPorts2 = io->win[1-i].len;
+ } else {
+ i = p_dev->io.NumPorts2 = 0;
+ }
+ p_dev->io.BasePort1 = io->win[i].base;
+ p_dev->io.NumPorts1 = io->win[i].len;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32)
+ return try_io_port(p_dev);
+
+ return -ENODEV;
+}
+
static int axnet_config(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
axnet_dev_t *info = PRIV(dev);
- tuple_t tuple;
- cisparse_t parse;
int i, j, last_ret, last_fn;
- u_short buf[64];
DECLARE_MAC_BUF(mac);
DEBUG(0, "axnet_config(0x%p)\n", link);
- tuple.Attributes = 0;
- tuple.TupleData = (cisdata_t *)buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
/* don't trust the CIS on this; Linksys got it wrong */
link->conf.Present = 0x63;
-
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- tuple.Attributes = 0;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (last_ret == CS_SUCCESS) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- cistpl_io_t *io = &(parse.cftable_entry.io);
-
- if (pcmcia_get_tuple_data(link, &tuple) != 0 ||
- pcmcia_parse_tuple(link, &tuple, &parse) != 0 ||
- cfg->index == 0 || cfg->io.nwin == 0)
- goto next_entry;
-
- link->conf.ConfigIndex = 0x05;
- /* For multifunction cards, by convention, we configure the
- network function with window 0, and serial with window 1 */
- if (io->nwin > 1) {
- i = (io->win[1].len > io->win[0].len);
- link->io.BasePort2 = io->win[1-i].base;
- link->io.NumPorts2 = io->win[1-i].len;
- } else {
- i = link->io.NumPorts2 = 0;
- }
- link->io.BasePort1 = io->win[i].base;
- link->io.NumPorts1 = io->win[i].len;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- if (link->io.NumPorts1 + link->io.NumPorts2 >= 32) {
- last_ret = try_io_port(link);
- if (last_ret == CS_SUCCESS) break;
- }
- next_entry:
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- }
+ last_ret = pcmcia_loop_config(link, axnet_configcheck, NULL);
if (last_ret != CS_SUCCESS) {
cs_error(link, RequestIO, last_ret);
goto failed;
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 2d4c4ad..7a9eeca 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -512,58 +512,53 @@ static int try_io_port(struct pcmcia_device *link)
}
}
+static int pcnet_confcheck(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ int *has_shmem = priv_data;
+ int i;
+ cistpl_io_t *io = &cfg->io;
+
+ if (cfg->index == 0 || cfg->io.nwin == 0)
+ return -EINVAL;
+
+ p_dev->conf.ConfigIndex = cfg->index;
+
+ /* For multifunction cards, by convention, we configure the
+ network function with window 0, and serial with window 1 */
+ if (io->nwin > 1) {
+ i = (io->win[1].len > io->win[0].len);
+ p_dev->io.BasePort2 = io->win[1-i].base;
+ p_dev->io.NumPorts2 = io->win[1-i].len;
+ } else {
+ i = p_dev->io.NumPorts2 = 0;
+ }
+
+ *has_shmem = ((cfg->mem.nwin == 1) &&
+ (cfg->mem.win[0].len >= 0x4000));
+ p_dev->io.BasePort1 = io->win[i].base;
+ p_dev->io.NumPorts1 = io->win[i].len;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32)
+ return try_io_port(p_dev);
+
+ return 0;
+}
+
static int pcnet_config(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
pcnet_dev_t *info = PRIV(dev);
- tuple_t tuple;
- cisparse_t parse;
- int i, last_ret, last_fn, start_pg, stop_pg, cm_offset;
+ int last_ret, last_fn, start_pg, stop_pg, cm_offset;
int has_shmem = 0;
- u_short buf[64];
hw_info_t *local_hw_info;
DECLARE_MAC_BUF(mac);
DEBUG(0, "pcnet_config(0x%p)\n", link);
- tuple.TupleData = (cisdata_t *)buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- tuple.Attributes = 0;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (last_ret == CS_SUCCESS) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- cistpl_io_t *io = &(parse.cftable_entry.io);
-
- if (pcmcia_get_tuple_data(link, &tuple) != 0 ||
- pcmcia_parse_tuple(link, &tuple, &parse) != 0 ||
- cfg->index == 0 || cfg->io.nwin == 0)
- goto next_entry;
-
- link->conf.ConfigIndex = cfg->index;
- /* For multifunction cards, by convention, we configure the
- network function with window 0, and serial with window 1 */
- if (io->nwin > 1) {
- i = (io->win[1].len > io->win[0].len);
- link->io.BasePort2 = io->win[1-i].base;
- link->io.NumPorts2 = io->win[1-i].len;
- } else {
- i = link->io.NumPorts2 = 0;
- }
- has_shmem = ((cfg->mem.nwin == 1) &&
- (cfg->mem.win[0].len >= 0x4000));
- link->io.BasePort1 = io->win[i].base;
- link->io.NumPorts1 = io->win[i].len;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- if (link->io.NumPorts1 + link->io.NumPorts2 >= 32) {
- last_ret = try_io_port(link);
- if (last_ret == CS_SUCCESS) break;
- }
- next_entry:
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- }
- if (last_ret != CS_SUCCESS) {
+ last_ret = pcmcia_loop_config(link, pcnet_confcheck, &has_shmem);
+ if (last_ret) {
cs_error(link, RequestIO, last_ret);
goto failed;
}
diff --git a/drivers/net/pcmcia/smc91c92_cs.c b/drivers/net/pcmcia/smc91c92_cs.c
index 250eb19..c012e34 100644
--- a/drivers/net/pcmcia/smc91c92_cs.c
+++ b/drivers/net/pcmcia/smc91c92_cs.c
@@ -459,28 +459,36 @@ static int mhz_3288_power(struct pcmcia_device *link)
return 0;
}
+static int mhz_mfc_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cf,
+ void *priv_data)
+{
+ int k;
+ p_dev->conf.ConfigIndex = cf->index;
+ p_dev->io.BasePort2 = cf->io.win[0].base;
+ for (k = 0; k < 0x400; k += 0x10) {
+ if (k & 0x80)
+ continue;
+ p_dev->io.BasePort1 = k ^ 0x300;
+ if (!pcmcia_request_io(p_dev, &p_dev->io))
+ return 0;
+ }
+ return -ENODEV;
+}
+
static int mhz_mfc_config(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
struct smc_private *smc = netdev_priv(dev);
struct smc_cfg_mem *cfg_mem;
- tuple_t *tuple;
- cisparse_t *parse;
- cistpl_cftable_entry_t *cf;
- u_char *buf;
win_req_t req;
memreq_t mem;
- int i, k;
+ int i;
cfg_mem = kmalloc(sizeof(struct smc_cfg_mem), GFP_KERNEL);
if (!cfg_mem)
return CS_OUT_OF_RESOURCE;
- tuple = &cfg_mem->tuple;
- parse = &cfg_mem->parse;
- cf = &parse->cftable_entry;
- buf = cfg_mem->buf;
-
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
link->irq.Attributes =
@@ -489,27 +497,9 @@ static int mhz_mfc_config(struct pcmcia_device *link)
link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
link->io.NumPorts2 = 8;
- tuple->Attributes = tuple->TupleOffset = 0;
- tuple->TupleData = (cisdata_t *)buf;
- tuple->TupleDataMax = 255;
- tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY;
-
- i = first_tuple(link, tuple, parse);
/* The Megahertz combo cards have modem-like CIS entries, so
we have to explicitly try a bunch of port combinations. */
- while (i == CS_SUCCESS) {
- link->conf.ConfigIndex = cf->index;
- link->io.BasePort2 = cf->io.win[0].base;
- for (k = 0; k < 0x400; k += 0x10) {
- if (k & 0x80) continue;
- link->io.BasePort1 = k ^ 0x300;
- i = pcmcia_request_io(link, &link->io);
- if (i == CS_SUCCESS) break;
- }
- if (i == CS_SUCCESS) break;
- i = next_tuple(link, tuple, parse);
- }
- if (i != CS_SUCCESS)
+ if (pcmcia_loop_config(link, mhz_mfc_config_check, NULL))
goto free_cfg_mem;
dev->base_addr = link->io.BasePort1;
@@ -533,7 +523,7 @@ static int mhz_mfc_config(struct pcmcia_device *link)
free_cfg_mem:
kfree(cfg_mem);
- return i;
+ return -ENODEV;
}
static int mhz_setup(struct pcmcia_device *link)
@@ -660,46 +650,26 @@ static int mot_setup(struct pcmcia_device *link)
/*====================================================================*/
+static int smc_configcheck(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cf,
+ void *priv_data)
+{
+ p_dev->conf.ConfigIndex = cf->index;
+ p_dev->io.BasePort1 = cf->io.win[0].base;
+ p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
+ return pcmcia_request_io(p_dev, &p_dev->io);
+}
+
static int smc_config(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
- struct smc_cfg_mem *cfg_mem;
- tuple_t *tuple;
- cisparse_t *parse;
- cistpl_cftable_entry_t *cf;
- u_char *buf;
int i;
- cfg_mem = kmalloc(sizeof(struct smc_cfg_mem), GFP_KERNEL);
- if (!cfg_mem)
- return CS_OUT_OF_RESOURCE;
-
- tuple = &cfg_mem->tuple;
- parse = &cfg_mem->parse;
- cf = &parse->cftable_entry;
- buf = cfg_mem->buf;
-
- tuple->Attributes = tuple->TupleOffset = 0;
- tuple->TupleData = (cisdata_t *)buf;
- tuple->TupleDataMax = 255;
- tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY;
-
link->io.NumPorts1 = 16;
- i = first_tuple(link, tuple, parse);
- while (i != CS_NO_MORE_ITEMS) {
- if (i == CS_SUCCESS) {
- link->conf.ConfigIndex = cf->index;
- link->io.BasePort1 = cf->io.win[0].base;
- link->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
- i = pcmcia_request_io(link, &link->io);
- if (i == CS_SUCCESS) break;
- }
- i = next_tuple(link, tuple, parse);
- }
- if (i == CS_SUCCESS)
- dev->base_addr = link->io.BasePort1;
+ i = pcmcia_loop_config(link, smc_configcheck, NULL);
+ if (!i)
+ dev->base_addr = link->io.BasePort1;
- kfree(cfg_mem);
return i;
}
diff --git a/drivers/net/pcmcia/xirc2ps_cs.c b/drivers/net/pcmcia/xirc2ps_cs.c
index f6c4698..b57f022 100644
--- a/drivers/net/pcmcia/xirc2ps_cs.c
+++ b/drivers/net/pcmcia/xirc2ps_cs.c
@@ -715,6 +715,45 @@ has_ce2_string(struct pcmcia_device * p_dev)
return 0;
}
+static int
+xirc2ps_config_modem(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cf,
+ void *priv_data)
+{
+ unsigned int ioaddr;
+
+ if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) {
+ for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) {
+ p_dev->conf.ConfigIndex = cf->index ;
+ p_dev->io.BasePort2 = cf->io.win[0].base;
+ p_dev->io.BasePort1 = ioaddr;
+ if (!pcmcia_request_io(p_dev, &p_dev->io))
+ return 0;
+ }
+ }
+ return -ENODEV;
+}
+
+static int
+xirc2ps_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cf,
+ void *priv_data)
+{
+ int *pass = priv_data;
+
+ if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) {
+ p_dev->conf.ConfigIndex = cf->index ;
+ p_dev->io.BasePort2 = cf->io.win[0].base;
+ p_dev->io.BasePort1 = p_dev->io.BasePort2
+ + (*pass ? (cf->index & 0x20 ? -24:8)
+ : (cf->index & 0x20 ? 8:-24));
+ if (!pcmcia_request_io(p_dev, &p_dev->io))
+ return 0;
+ }
+ return -ENODEV;
+
+}
+
/****************
* xirc2ps_config() is scheduled to run after a CARD_INSERTION event
* is received, to configure the PCMCIA socket, and to make the
@@ -725,13 +764,12 @@ xirc2ps_config(struct pcmcia_device * link)
{
struct net_device *dev = link->priv;
local_info_t *local = netdev_priv(dev);
+ unsigned int ioaddr;
tuple_t tuple;
cisparse_t parse;
- unsigned int ioaddr;
int err, i;
u_char buf[64];
cistpl_lan_node_id_t *node_id = (cistpl_lan_node_id_t*)parse.funce.data;
- cistpl_cftable_entry_t *cf = &parse.cftable_entry;
DECLARE_MAC_BUF(mac);
local->dingo_ccr = NULL;
@@ -846,19 +884,8 @@ xirc2ps_config(struct pcmcia_device * link)
/* Take the Modem IO port from the CIS and scan for a free
* Ethernet port */
link->io.NumPorts1 = 16; /* no Mako stuff anymore */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- for (err = first_tuple(link, &tuple, &parse); !err;
- err = next_tuple(link, &tuple, &parse)) {
- if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) {
- for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) {
- link->conf.ConfigIndex = cf->index ;
- link->io.BasePort2 = cf->io.win[0].base;
- link->io.BasePort1 = ioaddr;
- if (!(err=pcmcia_request_io(link, &link->io)))
- goto port_found;
- }
- }
- }
+ if (!pcmcia_loop_config(link, xirc2ps_config_modem, NULL))
+ goto port_found;
} else {
link->io.NumPorts1 = 18;
/* We do 2 passes here: The first one uses the regular mapping and
@@ -866,21 +893,9 @@ xirc2ps_config(struct pcmcia_device * link)
* mirrored every 32 bytes. Actually we use a mirrored port for
* the Mako if (on the first pass) the COR bit 5 is set.
*/
- for (pass=0; pass < 2; pass++) {
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- for (err = first_tuple(link, &tuple, &parse); !err;
- err = next_tuple(link, &tuple, &parse)){
- if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8){
- link->conf.ConfigIndex = cf->index ;
- link->io.BasePort2 = cf->io.win[0].base;
- link->io.BasePort1 = link->io.BasePort2
- + (pass ? (cf->index & 0x20 ? -24:8)
- : (cf->index & 0x20 ? 8:-24));
- if (!(err=pcmcia_request_io(link, &link->io)))
+ for (pass=0; pass < 2; pass++)
+ if (!pcmcia_loop_config(link, xirc2ps_config_check, &pass))
goto port_found;
- }
- }
- }
/* if special option:
* try to configure as Ethernet only.
* .... */
diff --git a/drivers/net/wireless/airo_cs.c b/drivers/net/wireless/airo_cs.c
index f123553..4fbe811 100644
--- a/drivers/net/wireless/airo_cs.c
+++ b/drivers/net/wireless/airo_cs.c
@@ -206,126 +206,131 @@ static void airo_detach(struct pcmcia_device *link)
#define CS_CHECK(fn, ret) \
do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
+struct airo_cs_config_data {
+ cistpl_cftable_entry_t dflt;
+ win_req_t req;
+};
+
+static int airo_cs_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ struct airo_cs_config_data *cfg_mem = priv_data;
+
+ if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+ cfg_mem->dflt = *cfg;
+
+ if (cfg->index == 0)
+ return -ENODEV;
+
+ p_dev->conf.ConfigIndex = cfg->index;
+
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
+ }
+
+ /* Use power settings for Vcc and Vpp if present */
+ /* Note that the CIS values need to be rescaled */
+ if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
+ else if (cfg_mem->dflt.vpp1.present & (1<<CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM]/10000;
+
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || cfg_mem->dflt.irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ }
+
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ return -ENODEV;
+
+ /*
+ Now set up a common memory window, if needed. There is room
+ in the struct pcmcia_device structure for one memory window handle,
+ but if the base addresses need to be saved, or if multiple
+ windows are needed, the info should go in the private data
+ structure for this device.
+
+ Note that the memory window base is a physical address, and
+ needs to be mapped to virtual space with ioremap() before it
+ is used.
+ */
+ if ((cfg->mem.nwin > 0) || (cfg_mem->dflt.mem.nwin > 0)) {
+ cistpl_mem_t *mem = (cfg->mem.nwin) ? &cfg->mem : &cfg_mem->dflt.mem;
+ memreq_t map;
+ cfg_mem->req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM;
+ cfg_mem->req.Base = mem->win[0].host_addr;
+ cfg_mem->req.Size = mem->win[0].len;
+ cfg_mem->req.AccessSpeed = 0;
+ if (pcmcia_request_window(&p_dev, &cfg_mem->req, &p_dev->win) != 0)
+ return -ENODEV;
+ map.Page = 0;
+ map.CardOffset = mem->win[0].card_addr;
+ if (pcmcia_map_mem_page(p_dev->win, &map) != 0)
+ return -ENODEV;
+ }
+ /* If we got this far, we're cool! */
+ return 0;
+}
+
+
static int airo_config(struct pcmcia_device *link)
{
- tuple_t tuple;
- cisparse_t parse;
local_info_t *dev;
+ struct airo_cs_config_data *cfg_mem;
int last_fn, last_ret;
- u_char buf[64];
- win_req_t req;
- memreq_t map;
dev = link->priv;
DEBUG(0, "airo_config(0x%p)\n", link);
+ cfg_mem = kzalloc(sizeof(struct airo_cs_config_data), GFP_KERNEL);
+ if (!cfg_mem)
+ return -ENOMEM;
+
/*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
+ * In this loop, we scan the CIS for configuration table
+ * entries, each of which describes a valid card
+ * configuration, including voltage, IO window, memory window,
+ * and interrupt settings.
+ *
+ * We make no assumptions about the card to be configured: we
+ * use just the information available in the CIS. In an ideal
+ * world, this would work for any PCMCIA card, but it requires
+ * a complete and accurate CIS. In practice, a driver usually
+ * "knows" most of these things without consulting the CIS,
+ * and most client drivers will only use the CIS to fill in
+ * implementation-defined details.
+ */
+ last_ret = pcmcia_loop_config(link, airo_cs_config_check, cfg_mem);
+ if (last_ret)
+ goto failed;
+
+ /*
+ Allocate an interrupt line. Note that this does not assign a
+ handler to the interrupt, unless the 'Handler' member of the
+ irq structure is initialized.
*/
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (1) {
- cistpl_cftable_entry_t dflt = { 0 };
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple) != 0 ||
- pcmcia_parse_tuple(link, &tuple, &parse) != 0)
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg;
- if (cfg->index == 0) goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
- link->conf.Vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
- else if (dflt.vpp1.present & (1<<CISTPL_POWER_VNOM))
- link->conf.Vpp =
- dflt.vpp1.param[CISTPL_POWER_VNOM]/10000;
-
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- }
-
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
-
- /*
- Now set up a common memory window, if needed. There is room
- in the struct pcmcia_device structure for one memory window handle,
- but if the base addresses need to be saved, or if multiple
- windows are needed, the info should go in the private data
- structure for this device.
-
- Note that the memory window base is a physical address, and
- needs to be mapped to virtual space with ioremap() before it
- is used.
- */
- if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
- cistpl_mem_t *mem =
- (cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
- req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM;
- req.Base = mem->win[0].host_addr;
- req.Size = mem->win[0].len;
- req.AccessSpeed = 0;
- if (pcmcia_request_window(&link, &req, &link->win) != 0)
- goto next_entry;
- map.Page = 0; map.CardOffset = mem->win[0].card_addr;
- if (pcmcia_map_mem_page(link->win, &map) != 0)
- goto next_entry;
- }
- /* If we got this far, we're cool! */
- break;
-
- next_entry:
- CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(link, &tuple));
- }
-
- /*
- Allocate an interrupt line. Note that this does not assign a
- handler to the interrupt, unless the 'Handler' member of the
- irq structure is initialized.
- */
if (link->conf.Attributes & CONF_ENABLE_IRQ)
CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq));
@@ -362,14 +367,17 @@ static int airo_config(struct pcmcia_device *link)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
if (link->win)
- printk(", mem 0x%06lx-0x%06lx", req.Base,
- req.Base+req.Size-1);
+ printk(", mem 0x%06lx-0x%06lx", cfg_mem->req.Base,
+ cfg_mem->req.Base+cfg_mem->req.Size-1);
printk("\n");
+ kfree(cfg_mem);
return 0;
cs_failed:
cs_error(link, last_fn, last_ret);
+ failed:
airo_release(link);
+ kfree(cfg_mem);
return -ENODEV;
} /* airo_config */
diff --git a/drivers/net/wireless/atmel_cs.c b/drivers/net/wireless/atmel_cs.c
index 12617cd..263c36f 100644
--- a/drivers/net/wireless/atmel_cs.c
+++ b/drivers/net/wireless/atmel_cs.c
@@ -224,25 +224,69 @@ static int card_present(void *arg)
return 0;
}
+static int atmel_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ cistpl_cftable_entry_t *dflt = priv_data;
+
+ if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+ *dflt = *cfg;
+ if (cfg->index == 0)
+ return -ENODEV;
+ p_dev->conf.ConfigIndex = cfg->index;
+
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
+ }
+
+ /* Use power settings for Vcc and Vpp if present */
+ /* Note that the CIS values need to be rescaled */
+ if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
+ else if (dflt->vpp1.present & (1<<CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = dflt->vpp1.param[CISTPL_POWER_VNOM]/10000;
+
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ }
+
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(p_dev, &p_dev->io);
+}
+
static int atmel_config(struct pcmcia_device *link)
{
- tuple_t tuple;
- cisparse_t parse;
local_info_t *dev;
int last_fn, last_ret;
- u_char buf[64];
struct pcmcia_device_id *did;
+ cistpl_cftable_entry_t dflt = { 0 };
dev = link->priv;
did = handle_to_dev(link).driver_data;
DEBUG(0, "atmel_config(0x%p)\n", link);
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including
@@ -255,66 +299,8 @@ static int atmel_config(struct pcmcia_device *link)
these things without consulting the CIS, and most client drivers
will only use the CIS to fill in implementation-defined details.
*/
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (1) {
- cistpl_cftable_entry_t dflt = { 0 };
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple) != 0 ||
- pcmcia_parse_tuple(link, &tuple, &parse) != 0)
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg;
- if (cfg->index == 0) goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
- link->conf.Vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
- else if (dflt.vpp1.present & (1<<CISTPL_POWER_VNOM))
- link->conf.Vpp =
- dflt.vpp1.param[CISTPL_POWER_VNOM]/10000;
-
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- }
-
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
-
- /* If we got this far, we're cool! */
- break;
-
- next_entry:
- CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(link, &tuple));
- }
+ if (pcmcia_loop_config(link, atmel_config_check, &dflt))
+ goto failed;
/*
Allocate an interrupt line. Note that this does not assign a
@@ -360,6 +346,7 @@ static int atmel_config(struct pcmcia_device *link)
cs_failed:
cs_error(link, last_fn, last_ret);
+ failed:
atmel_release(link);
return -ENODEV;
}
diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c
index 3b4e55c..3d914dd 100644
--- a/drivers/net/wireless/hostap/hostap_cs.c
+++ b/drivers/net/wireless/hostap/hostap_cs.c
@@ -532,145 +532,134 @@ static void prism2_detach(struct pcmcia_device *link)
#define CS_CHECK(fn, ret) \
do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
-#define CFG_CHECK2(fn, retf) \
-do { int _ret = (retf); \
-if (_ret != 0) { \
- PDEBUG(DEBUG_EXTRA, "CardServices(" #fn ") returned %d\n", _ret); \
- cs_error(link, fn, _ret); \
- goto next_entry; \
-} \
-} while (0)
-
/* run after a CARD_INSERTION event is received to configure the PCMCIA
* socket and make the device available to the system */
+
+struct prism2_config_data {
+ cistpl_cftable_entry_t dflt;
+ config_info_t conf;
+};
+
+static int prism2_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ struct prism2_config_data *cfg_mem = priv_data;
+
+ if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+ cfg_mem->dflt = *cfg;
+ if (cfg->index == 0)
+ return -ENODEV;
+
+ p_dev->conf.ConfigIndex = cfg->index;
+ PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X "
+ "(default 0x%02X)\n", cfg->index, cfg_mem->dflt.index);
+
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
+ }
+
+ /* Use power settings for Vcc and Vpp if present */
+ /* Note that the CIS values need to be rescaled */
+ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] /
+ 10000 && !ignore_cis_vcc) {
+ PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping"
+ " this entry\n");
+ return -ENODEV;
+ }
+ } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] /
+ 10000 && !ignore_cis_vcc) {
+ PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch "
+ "- skipping this entry\n");
+ return -ENODEV;
+ }
+ }
+
+ if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
+ else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp = cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
+
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || cfg_mem->dflt.irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+ else if (!(p_dev->conf.Attributes & CONF_ENABLE_IRQ)) {
+ /* At least Compaq WL200 does not have IRQInfo1 set,
+ * but it does not work without interrupts.. */
+ printk(KERN_WARNING "Config has no IRQ info, but trying to "
+ "enable IRQ anyway..\n");
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+ }
+
+ /* IO window settings */
+ PDEBUG(DEBUG_EXTRA, "IO window settings: cfg->io.nwin=%d "
+ "cfg_mem->dflt.io.nwin=%d\n",
+ cfg->io.nwin, cfg_mem->dflt.io.nwin);
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ PDEBUG(DEBUG_EXTRA, "io->flags = 0x%04X, "
+ "io.base=0x%04x, len=%d\n", io->flags,
+ io->win[0].base, io->win[0].len);
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags &
+ CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ }
+
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(p_dev, &p_dev->io);
+}
+
static int prism2_config(struct pcmcia_device *link)
{
struct net_device *dev;
struct hostap_interface *iface;
+ struct prism2_config_data *cfg_mem;
local_info_t *local;
int ret = 1;
- tuple_t tuple;
- cisparse_t *parse;
int last_fn, last_ret;
- u_char buf[64];
- config_info_t conf;
- cistpl_cftable_entry_t dflt = { 0 };
struct hostap_cs_priv *hw_priv;
PDEBUG(DEBUG_FLOW, "prism2_config()\n");
- parse = kmalloc(sizeof(cisparse_t), GFP_KERNEL);
+ cfg_mem = kzalloc(sizeof(struct prism2_config_data), GFP_KERNEL);
+ if (!cfg_mem)
+ return -ENOMEM;
+
hw_priv = kzalloc(sizeof(*hw_priv), GFP_KERNEL);
- if (parse == NULL || hw_priv == NULL) {
+ if (hw_priv == NULL) {
ret = -ENOMEM;
goto failed;
}
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
CS_CHECK(GetConfigurationInfo,
- pcmcia_get_configuration_info(link, &conf));
+ pcmcia_get_configuration_info(link, &cfg_mem->conf));
/* Look for an appropriate configuration table entry in the CIS */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- for (;;) {
- cistpl_cftable_entry_t *cfg = &(parse->cftable_entry);
- CFG_CHECK2(GetTupleData,
- pcmcia_get_tuple_data(link, &tuple));
- CFG_CHECK2(ParseTuple,
- pcmcia_parse_tuple(link, &tuple, parse));
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
- PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X "
- "(default 0x%02X)\n", cfg->index, dflt.index);
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping"
- " this entry\n");
- goto next_entry;
- }
- } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch "
- "- skipping this entry\n");
- goto next_entry;
- }
- }
-
- if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
- else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
-
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
- else if (!(link->conf.Attributes & CONF_ENABLE_IRQ)) {
- /* At least Compaq WL200 does not have IRQInfo1 set,
- * but it does not work without interrupts.. */
- printk("Config has no IRQ info, but trying to enable "
- "IRQ anyway..\n");
- link->conf.Attributes |= CONF_ENABLE_IRQ;
- }
-
- /* IO window settings */
- PDEBUG(DEBUG_EXTRA, "IO window settings: cfg->io.nwin=%d "
- "dflt.io.nwin=%d\n",
- cfg->io.nwin, dflt.io.nwin);
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- PDEBUG(DEBUG_EXTRA, "io->flags = 0x%04X, "
- "io.base=0x%04x, len=%d\n", io->flags,
- io->win[0].base, io->win[0].len);
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags &
- CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- }
-
- /* This reserves IO space but doesn't actually enable it */
- CFG_CHECK2(RequestIO,
- pcmcia_request_io(link, &link->io));
-
- /* This configuration table entry is OK */
- break;
-
- next_entry:
- CS_CHECK(GetNextTuple,
- pcmcia_get_next_tuple(link, &tuple));
+ last_ret = pcmcia_loop_config(link, prism2_config_check, cfg_mem);
+ if (last_ret) {
+ if (!ignore_cis_vcc)
+ printk(KERN_ERR "GetNextTuple(): No matching "
+ "CIS configuration. Maybe you need the "
+ "ignore_cis_vcc=1 parameter.\n");
+ cs_error(link, RequestIO, last_ret);
+ goto failed;
}
/* Need to allocate net_device before requesting IRQ handler */
@@ -738,15 +727,15 @@ static int prism2_config(struct pcmcia_device *link)
if (ret == 0 && local->ddev)
strcpy(hw_priv->node.dev_name, local->ddev->name);
}
- kfree(parse);
+ kfree(cfg_mem);
return ret;
cs_failed:
cs_error(link, last_fn, last_ret);
failed:
- kfree(parse);
kfree(hw_priv);
+ kfree(cfg_mem);
prism2_release((u_long)link);
return ret;
}
diff --git a/drivers/net/wireless/orinoco_cs.c b/drivers/net/wireless/orinoco_cs.c
index 1c216e0..473370c 100644
--- a/drivers/net/wireless/orinoco_cs.c
+++ b/drivers/net/wireless/orinoco_cs.c
@@ -164,23 +164,96 @@ static void orinoco_cs_detach(struct pcmcia_device *link)
last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; \
} while (0)
+struct orinoco_cs_config_data {
+ cistpl_cftable_entry_t dflt;
+ config_info_t conf;
+};
+
+static int orinoco_cs_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ struct orinoco_cs_config_data *cfg_mem = priv_data;
+
+ if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+ cfg_mem->dflt = *cfg;
+ if (cfg->index == 0)
+ goto next_entry;
+ p_dev->conf.ConfigIndex = cfg->index;
+
+ /* Use power settings for Vcc and Vpp if present */
+ /* Note that the CIS values need to be rescaled */
+ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
+ DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
+ if (!ignore_cis_vcc)
+ goto next_entry;
+ }
+ } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) {
+ DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000);
+ if (!ignore_cis_vcc)
+ goto next_entry;
+ }
+ }
+
+ if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp =
+ cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
+ else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp =
+ cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
+
+ /* Do we need to allocate an interrupt? */
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ goto next_entry;
+ }
+ return 0;
+
+next_entry:
+ pcmcia_disable_device(p_dev);
+ return -ENODEV;
+};
+
static int
orinoco_cs_config(struct pcmcia_device *link)
{
+ struct orinoco_cs_config_data *cfg_mem;
struct net_device *dev = link->priv;
struct orinoco_private *priv = netdev_priv(dev);
struct orinoco_pccard *card = priv->card;
hermes_t *hw = &priv->hw;
int last_fn, last_ret;
- u_char buf[64];
- config_info_t conf;
- tuple_t tuple;
- cisparse_t parse;
void __iomem *mem;
+ cfg_mem = kzalloc(sizeof(struct orinoco_cs_config_data), GFP_KERNEL);
+ if (!cfg_mem)
+ return -ENOMEM;
+
/* Look up the current Vcc */
CS_CHECK(GetConfigurationInfo,
- pcmcia_get_configuration_info(link, &conf));
+ pcmcia_get_configuration_info(link, &cfg_mem->conf));
/*
* In this loop, we scan the CIS for configuration table
@@ -196,94 +269,14 @@ orinoco_cs_config(struct pcmcia_device *link)
* and most client drivers will only use the CIS to fill in
* implementation-defined details.
*/
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- cistpl_cftable_entry_t dflt = { .index = 0 };
-
- if ( (pcmcia_get_tuple_data(link, &tuple) != 0)
- || (pcmcia_parse_tuple(link, &tuple, &parse) != 0))
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, cfg CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, dflt CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000);
- if(!ignore_cis_vcc)
- goto next_entry;
- }
- }
-
- if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
- else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
-
- /* Do we need to allocate an interrupt? */
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io =
- (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 =
- IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 =
- IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines =
- io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 =
- link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
-
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
- }
-
-
- /* If we got this far, we're cool! */
-
- break;
-
- next_entry:
- pcmcia_disable_device(link);
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret == CS_NO_MORE_ITEMS) {
+ last_ret = pcmcia_loop_config(link, orinoco_cs_config_check, cfg_mem);
+ if (last_ret) {
+ if (!ignore_cis_vcc)
printk(KERN_ERR PFX "GetNextTuple(): No matching "
"CIS configuration. Maybe you need the "
"ignore_cis_vcc=1 parameter.\n");
- goto cs_failed;
- }
+ cs_error(link, RequestIO, last_ret);
+ goto failed;
}
/*
@@ -334,7 +327,7 @@ orinoco_cs_config(struct pcmcia_device *link)
"0x%04x-0x%04x\n", dev->name, dev->dev.parent->bus_id,
link->irq.AssignedIRQ, link->io.BasePort1,
link->io.BasePort1 + link->io.NumPorts1 - 1);
-
+ kfree(cfg_mem);
return 0;
cs_failed:
@@ -342,6 +335,7 @@ orinoco_cs_config(struct pcmcia_device *link)
failed:
orinoco_cs_release(link);
+ kfree(cfg_mem);
return -ENODEV;
} /* orinoco_cs_config */
diff --git a/drivers/net/wireless/spectrum_cs.c b/drivers/net/wireless/spectrum_cs.c
index 98df9bc..8e1951c 100644
--- a/drivers/net/wireless/spectrum_cs.c
+++ b/drivers/net/wireless/spectrum_cs.c
@@ -633,23 +633,96 @@ static void spectrum_cs_detach(struct pcmcia_device *link)
* device available to the system.
*/
+struct spectrum_cs_config_data {
+ cistpl_cftable_entry_t dflt;
+ config_info_t conf;
+};
+
+static int spectrum_cs_config_check(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ void *priv_data)
+{
+ struct spectrum_cs_config_data *cfg_mem = priv_data;
+
+ if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
+ cfg_mem->dflt = *cfg;
+ if (cfg->index == 0)
+ goto next_entry;
+ p_dev->conf.ConfigIndex = cfg->index;
+
+ /* Use power settings for Vcc and Vpp if present */
+ /* Note that the CIS values need to be rescaled */
+ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
+ DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
+ if (!ignore_cis_vcc)
+ goto next_entry;
+ }
+ } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
+ if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) {
+ DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000);
+ if (!ignore_cis_vcc)
+ goto next_entry;
+ }
+ }
+
+ if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp =
+ cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
+ else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
+ p_dev->conf.Vpp =
+ cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
+
+ /* Do we need to allocate an interrupt? */
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ goto next_entry;
+ }
+ return 0;
+
+next_entry:
+ pcmcia_disable_device(p_dev);
+ return -ENODEV;
+};
+
static int
spectrum_cs_config(struct pcmcia_device *link)
{
+ struct spectrum_cs_config_data *cfg_mem;
struct net_device *dev = link->priv;
struct orinoco_private *priv = netdev_priv(dev);
struct orinoco_pccard *card = priv->card;
hermes_t *hw = &priv->hw;
int last_fn, last_ret;
- u_char buf[64];
- config_info_t conf;
- tuple_t tuple;
- cisparse_t parse;
void __iomem *mem;
+ cfg_mem = kzalloc(sizeof(struct spectrum_cs_config_data), GFP_KERNEL);
+ if (!cfg_mem)
+ return -ENOMEM;
+
/* Look up the current Vcc */
CS_CHECK(GetConfigurationInfo,
- pcmcia_get_configuration_info(link, &conf));
+ pcmcia_get_configuration_info(link, &cfg_mem->conf));
/*
* In this loop, we scan the CIS for configuration table
@@ -665,94 +738,14 @@ spectrum_cs_config(struct pcmcia_device *link)
* and most client drivers will only use the CIS to fill in
* implementation-defined details.
*/
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- cistpl_cftable_entry_t dflt = { .index = 0 };
-
- if ( (pcmcia_get_tuple_data(link, &tuple) != 0)
- || (pcmcia_parse_tuple(link, &tuple, &parse) != 0))
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "spectrum_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "spectrum_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000);
- if(!ignore_cis_vcc)
- goto next_entry;
- }
- }
-
- if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
- else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM))
- link->conf.Vpp =
- dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000;
-
- /* Do we need to allocate an interrupt? */
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io =
- (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 =
- IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 =
- IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines =
- io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 =
- link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
-
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
- }
-
-
- /* If we got this far, we're cool! */
-
- break;
-
- next_entry:
- pcmcia_disable_device(link);
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret == CS_NO_MORE_ITEMS) {
+ last_ret = pcmcia_loop_config(link, spectrum_cs_config_check, cfg_mem);
+ if (last_ret) {
+ if (!ignore_cis_vcc)
printk(KERN_ERR PFX "GetNextTuple(): No matching "
"CIS configuration. Maybe you need the "
"ignore_cis_vcc=1 parameter.\n");
- goto cs_failed;
- }
+ cs_error(link, RequestIO, last_ret);
+ goto failed;
}
/*
@@ -809,6 +802,7 @@ spectrum_cs_config(struct pcmcia_device *link)
link->irq.AssignedIRQ, link->io.BasePort1,
link->io.BasePort1 + link->io.NumPorts1 - 1);
+ kfree(cfg_mem);
return 0;
cs_failed:
@@ -816,6 +810,7 @@ spectrum_cs_config(struct pcmcia_device *link)
failed:
spectrum_cs_release(link);
+ kfree(cfg_mem);
return -ENODEV;
} /* spectrum_cs_config */
--
1.5.4.3
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists