netdev - RE: [SMC911x ]fix for driver resume and compilation warning

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [day] [month] [year] [list]

Message-ID: <B85A65D85D7EB246BE421B3FB0FBB59301B34DC1C0@dbde02.ent.ti.com>
Date:	Fri, 7 Nov 2008 13:50:32 +0530
From:	"Dasgupta, Romit" <romit@...com>
To:	"jgarzik@...ox.com" <jgarzik@...ox.com>,
	"nico@....org" <nico@....org>
CC:	"netdev@...r.kernel.org" <netdev@...r.kernel.org>
Subject: RE: [SMC911x ]fix for driver resume and compilation warning 

Hi,
                            I think Dustin's email is bouncing back. So I am resending this. Could you kindly tell me who would be the right person to push this code to? 

Thanks,
-Romit

-----Original Message-----
From: Dasgupta, Romit 
Sent: Thursday, November 06, 2008 3:46 PM
To: 'dustin@...soria.com'; 'jgarzik@...ox.com'; 'nico@....org'
Cc: 'netdev@...r.kernel.org'; linux-omap@...r.kernel.org
Subject: [SMC911x ]fix for driver resume and compilation warning 

Hi,
     I am trying out suspend, resume on an OMAP3 based board. What I see during resume is that the SMC911x driver resume routing gets stuck after trying to transmit the packet out of the controller. Some debug messages below:

--> smc911x_drv_resume
eth0: --> smc911x_reset
eth0: smc911x_reset timeout waiting for PM restore
eth0: --> smc911x_enable
eth0: --> smc911x_phy_configure()
eth0: --> smc911x_phy_reset()
eth0: phy caps=0x782d
eth0: phy advertised caps=0x0de1
eth0: --> smc911x_phy_check_media
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
eth0: link down
Restarting tasks ... eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
nfs: server 172.24.190.217 not responding, still trying
nfs: server 172.24.190.217 not responding, still trying


The following change makes it work fine: (The change within smc911x_drv_probe function was to get rid of a compilation warning).
Additionally, the SMC9211 data sheet says that when we enter D2 sleep state, we need to set the EDPWRDOWN bit in the PHY Mode control/status register and clear it when we are back to D0. This is not done in the code as far as I can see. So does it mean that the PHY is not powered down but the controller is? I have another patch that fixes it. I will send that as well unless I am missing something.

Thanks,
-Romit


Signed-off-by: Romit Dasgupta <romit@...com>

diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c
index 5051554..1f26ab0 100644
--- a/drivers/net/smc911x.c
+++ b/drivers/net/smc911x.c
@@ -2050,7 +2050,9 @@ err_out:
  */
 static int smc911x_drv_probe(struct platform_device *pdev)
 {
+#ifdef SMC_DYNAMIC_BUS_CONFIG
 	struct smc911x_platdata *pd = pdev->dev.platform_data;
+#endif
 	struct net_device *ndev;
 	struct resource *res;
 	struct smc911x_local *lp;
@@ -2182,9 +2184,9 @@ static int smc911x_drv_resume(struct platform_device *dev)
 
 		if (netif_running(ndev)) {
 			smc911x_reset(ndev);
-			smc911x_enable(ndev);
 			if (lp->phy_type != 0)
 				smc911x_phy_configure(&lp->phy_configure);
+			smc911x_enable(ndev);
 			netif_device_attach(ndev);
 		}
 	}
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html