Network driver for the SPI version of the Micrel KS8851 network chip. Signed-off-by: Ben Dooks --- drivers/net/Kconfig | 6 drivers/net/Makefile | 1 drivers/net/ks8851.c | 1322 +++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/ks8851.h | 296 +++++++++++ 4 files changed, 1625 insertions(+) Index: b/drivers/net/Kconfig =================================================================== --- a/drivers/net/Kconfig 2009-07-15 13:02:56.000000000 +0100 +++ b/drivers/net/Kconfig 2009-07-15 13:03:01.000000000 +0100 @@ -1729,6 +1729,12 @@ config KS8842 help This platform driver is for Micrel KSZ8842 chip. +config KS8851 + tristate "Micrel KS8851 SPI" + depends on SPI + help + SPI driver for Micrel KS8851 SPI attached network chip. + config VIA_RHINE tristate "VIA Rhine support" depends on NET_PCI && PCI Index: b/drivers/net/Makefile =================================================================== --- a/drivers/net/Makefile 2009-07-15 13:02:56.000000000 +0100 +++ b/drivers/net/Makefile 2009-07-15 13:03:01.000000000 +0100 @@ -88,6 +88,7 @@ obj-$(CONFIG_SKGE) += skge.o obj-$(CONFIG_SKY2) += sky2.o obj-$(CONFIG_SKFP) += skfp/ obj-$(CONFIG_KS8842) += ks8842.o +obj-$(CONFIG_KS8851) += ks8851.o obj-$(CONFIG_VIA_RHINE) += via-rhine.o obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o Index: b/drivers/net/ks8851.c =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ b/drivers/net/ks8851.c 2009-07-16 15:57:46.000000000 +0100 @@ -0,0 +1,1322 @@ +/* drivers/net/ks8651.c + * + * Copyright 2009 Simtec Electronics + * http://www.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define DEBUG + +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "ks8851.h" + +/** + * struct ks8851_rxctrl - KS8851 driver rx control + * @mchash: Multicast hash-table data. + * @rxcr1: KS_RXCR1 register setting + * @rxcr2: KS_RXCR2 register setting + * + * Representation of the settings needs to control the receive filtering + * such as the multicast hash-filter and the receive register settings. This + * is used to make the job of working out if the receive settings change and + * then issuing the new settings to the worker that will send the necessary + * commands. + */ +struct ks8851_rxctrl { + u16 mchash[4]; + u16 rxcr1; + u16 rxcr2; +}; + +/** + * union ks8851_tx_hdr - tx header data + * @txb: The header as bytes + * @txw: The header as 16bit, little-endian words + * + * A dual representation of the tx header data to allow + * access to individual bytes, and to allow 16bit accesses + * with 16bit alignment. + */ +union ks8851_tx_hdr { + u8 txb[6]; + __le16 txw[3]; +}; + +/** + * struct ks8851_net - KS8851 driver private data + * @netdev: The network device we're bound to + * @spidev: The spi device we're bound to. + * @lock: Lock to ensure that the device is not accessed when busy. + * @statelock: Lock on this structure for tx list. + * @mii: The MII state information for the mii calls. + * @rxctrl: RX settings for @rxctrl_work. + * @tx_work: Work queue for tx packets + * @irq_work: Work queue for servicing interrupts + * @rxctrl_work: Work queue for updating RX mode and multicast lists + * @txq: Queue of packets for transmission. + * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1. + * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2. + * @txh: Space for generating packet TX header in DMA-able data + * @rxd: Space for receiving SPI data, in DMA-able space. + * @txd: Space for transmitting SPI data, in DMA-able space. + * @msg_enable: The message flags controlling driver output (see ethtool). + * @fid: Incrementing frame id tag. + * @rc_ier: Cached copy of KS_IER. + * @rc_rxqcr: Cached copy of KS_RXQCR. + * + * The @lock ensures that the chip is protected when certain operations are + * in progress. When the read or write packet transfer is in progress, most + * of the chip registers are not ccessible until the transfer is finished and + * the DMA has been de-asserted. + * + * The @statelock is used to protect information in the structure which may + * need to be accessed via several sources, such as the network driver layer + * or one of the work queues. + * + * We align the buffers we may use for rx/tx to ensure that if the SPI driver + * wants to DMA map them, it will not have any problems with data the driver + * modifies. + */ +struct ks8851_net { + struct net_device *netdev; + struct spi_device *spidev; + struct mutex lock; + spinlock_t statelock; + + union ks8851_tx_hdr txh ____cacheline_aligned; + u8 rxd[8]; + u8 txd[8]; + + u32 msg_enable ____cacheline_aligned; + u16 tx_space; + u8 fid; + + u16 rc_ier; + u16 rc_rxqcr; + + struct mii_if_info mii; + struct ks8851_rxctrl rxctrl; + + struct work_struct tx_work; + struct work_struct irq_work; + struct work_struct rxctrl_work; + + struct sk_buff_head txq; + + struct spi_message spi_msg1; + struct spi_message spi_msg2; + struct spi_transfer spi_xfer1; + struct spi_transfer spi_xfer2[2]; +}; + +static int msg_enable; + +#define ks_info(_ks, _msg...) dev_info(&(_ks)->spidev->dev, _msg) +#define ks_warn(_ks, _msg...) dev_warn(&(_ks)->spidev->dev, _msg) +#define ks_dbg(_ks, _msg...) dev_dbg(&(_ks)->spidev->dev, _msg) +#define ks_err(_ks, _msg...) dev_err(&(_ks)->spidev->dev, _msg) + +/* shift for byte-enable data */ +#define BYTE_EN(_x) ((_x) << 2) + +/* turn register number and byte-enable mask into data for start of packet */ +#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6) + +/* SPI register read/write calls. + * + * All these calls issue SPI transactions to access the chip's registers. They + * all require that the necessary lock is held to prevent accesses when the + * chip is busy transfering packet data (RX/TX FIFO accesses). + */ + +/** + * ks8851_wrreg16 - write 16bit register value to chip + * @ks: The chip state + * @reg: The register address + * @val: The value to write + * + * Issue a write to put the value @val into the register specified in @reg. + */ +static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val) +{ + struct spi_transfer *xfer = &ks->spi_xfer1; + struct spi_message *msg = &ks->spi_msg1; + __le16 txb[2]; + int ret; + + txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR); + txb[1] = cpu_to_le16(val); + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 4; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "spi_sync() failed\n"); +} + +/** + * ks8851_rx_1msg - select whether to use one or two messages for spi read + * @ks: The device structure + * + * Return whether to generate a single message with a tx and rx buffer + * supplied to spi_sync(), or alternatively send the tx and rx buffers + * as separate messages. + * + * Depending on the hardware in use, a single message may be more efficient + * on interrupts or work done by the driver. + * + * This currently always returns true until we add some per-device data passed + * from the platform code to specify which mode is better. + */ +static inline bool ks8851_rx_1msg(struct ks8851_net *ks) +{ + return true; +} + +/** + * ks8851_rdreg - issue read register command and return the data + * @ks: The device state + * @op: The register address and byte enables in message format. + * @rxb: The RX buffer to return the result into + * @rxl: The length of data expected. + * + * This is the low level read call that issues the necessary spi message(s) + * to read data from the register specified in @op. + */ +static void ks8851_rdreg(struct ks8851_net *ks, unsigned op, + u8 *rxb, unsigned rxl) +{ + struct spi_transfer *xfer; + struct spi_message *msg; + __le16 *txb = (__le16 *)ks->txd; + u8 *trx = ks->rxd; + int ret; + + txb[0] = cpu_to_le16(op | KS_SPIOP_RD); + + if (ks8851_rx_1msg(ks)) { + msg = &ks->spi_msg1; + xfer = &ks->spi_xfer1; + + xfer->tx_buf = txb; + xfer->rx_buf = trx; + xfer->len = rxl + 2; + } else { + msg = &ks->spi_msg2; + xfer = ks->spi_xfer2; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 2; + + xfer++; + xfer->tx_buf = NULL; + xfer->rx_buf = trx; + xfer->len = rxl; + } + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "read: spi_sync() failed\n"); + else if (ks8851_rx_1msg(ks)) + memcpy(rxb, trx + 2, rxl); + else + memcpy(rxb, trx, rxl); +} + +/** + * ks8851_rdreg8 - read 8 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 8bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg) +{ + u8 rxb[1]; + + ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1); + return rxb[0]; +} + +/** + * ks8851_rdreg16 - read 16 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 16bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg) +{ + __le16 rx = 0; + + ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2); + return le16_to_cpu(rx); +} + +/** + * ks8851_rdreg32 - read 32 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 32bit register from the chip. + * + * Note, this read requires the address be aligned to 4 bytes. +*/ +static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg) +{ + __le32 rx = 0; + + WARN_ON(reg & 3); + + ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4); + return le32_to_cpu(rx); +} + +/** + * ks8851_soft_reset - issue one of the soft reset to the device + * @ks: The device state. + * @op: The bit(s) to set in the GRR + * + * Issue the relevant soft-reset command to the device's GRR register + * specified by @op. + * + * Note, the delays are in there as a caution to ensure that the reset + * has time to take effect and then complete. Since the datasheet does + * not currently specify the exact sequence, we have chosen something + * that seems to work with our device. + */ +static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op) +{ + ks8851_wrreg16(ks, KS_GRR, op); + mdelay(1); /* wait a short time to effect reset */ + ks8851_wrreg16(ks, KS_GRR, 0); + mdelay(1); /* wait for condition to clear */ +} + +/** + * ks8851_write_mac_addr - write mac address to device registers + * @dev: The network device + * + * Update the KS8851 MAC address registers from the address in @dev. + * + * This call assumes that the chip is not running, so there is no need to + * shutdown the RXQ process whilst setting this. +*/ +static int ks8851_write_mac_addr(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + u16 *mcp = (u16 *)dev->dev_addr; + + mutex_lock(&ks->lock); + + ks8851_wrreg16(ks, KS_MARL, mcp[0]); + ks8851_wrreg16(ks, KS_MARM, mcp[1]); + ks8851_wrreg16(ks, KS_MARH, mcp[2]); + + mutex_unlock(&ks->lock); + + return 0; +} + +/** + * ks8851_init_mac - initialise the mac address + * @ks: The device structure + * + * Get or create the initial mac address for the device and then set that + * into the station address register. Currently we assume that the device + * does not have a valid mac address in it, and so we use random_ether_addr() + * to create a new one. + * + * In future, the driver should check to see if the device has an EEPROM + * attached and whether that has a valid ethernet address in it. + */ +static void ks8851_init_mac(struct ks8851_net *ks) +{ + struct net_device *dev = ks->netdev; + + random_ether_addr(dev->dev_addr); + ks8851_write_mac_addr(dev); +} + +/** + * ks8851_irq - device interrupt handler + * @irq: Interrupt number passed from the IRQ hnalder. + * @pw: The private word passed to register_irq(), our struct ks8851_net. + * + * Disable the interrupt from happening again until we've processed the + * current status by scheduling ks8851_irq_work(). + */ +static irqreturn_t ks8851_irq(int irq, void *pw) +{ + struct ks8851_net *ks = pw; + + disable_irq_nosync(irq); + schedule_work(&ks->irq_work); + return IRQ_HANDLED; +} + +/** + * ks8851_rdfifo - read data from the receive fifo + * @ks: The device state. + * @buff: The buffer address + * @len: The length of the data to read + * + * Issue an RXQ FIFO read command and read the @len ammount of data from + * the FIFO into the buffer specified by @buff. + */ +static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + u8 txb[1]; + int ret; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d@%p\n", __func__, len, buff); + + /* set the operation we're issuing */ + txb[0] = KS_SPIOP_RXFIFO; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 1; + + xfer++; + xfer->rx_buf = buff; + xfer->tx_buf = NULL; + xfer->len = len; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_dbg_dumpkkt - dump initial packet contents to debug + * @ks: The device state + * @rxpkt: The data for the received packet + * + * Dump the initial data from the packet to dev_dbg(). +*/ +static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt) +{ + ks_dbg(ks, "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n", + rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7], + rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11], + rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]); +} + +/** + * ks8851_rx_pkts - receive packets from the host + * @ks: The device information. + * + * This is called from the IRQ work queue when the system detects that there + * are packets in the receive queue. Find out how many packets there are and + * read them from the FIFO. + */ +static void ks8851_rx_pkts(struct ks8851_net *ks) +{ + struct sk_buff *skb; + unsigned rxfc; + unsigned rxlen; + unsigned rxstat; + u32 rxh; + u8 *rxpkt; + + rxfc = ks8851_rdreg8(ks, KS_RXFC); + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "%s: %d packets\n", __func__, rxfc); + + /* Currently we're issuing a read per packet, but we could possibly + * improve the code by issuing a single read, getting the receive + * header, allocating the packet and then reading the packet data + * out in one go. + * + * This form of operation would require us to hold the SPI bus' + * chipselect low during the entie transaction to avoid any + * reset to the data stream comming from the chip. + */ + + for (; rxfc != 0; rxfc--) { + rxh = ks8851_rdreg32(ks, KS_RXFHSR); + rxstat = rxh & 0xffff; + rxlen = rxh >> 16; + + if (netif_msg_rx_status(ks)) + ks_dbg(ks, "rx: stat 0x%04x, len 0x%04x\n", + rxstat, rxlen); + + /* the length of the packet includes the 32bit CRC */ + + /* set dma read address */ + ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00); + + /* start the packet dma process, and set auto-dequeue rx */ + ks8851_wrreg16(ks, KS_RXQCR, + ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE); + + if (rxlen > 0) { + skb = netdev_alloc_skb(ks->netdev, rxlen + 2 + 8); + if (!skb) { + /* todo - dump frame and move on */ + } + + /* two bytes to ensure ip is aligned, and four bytes + * for the status header and 4 bytes of garbage */ + skb_reserve(skb, 2 + 4 + 4); + + rxpkt = skb_put(skb, rxlen - 4) - 8; + + /* align the packet length to 4 bytes, and add 4 bytes + * as we're getting the rx status header as well */ + ks8851_rdfifo(ks, rxpkt, ALIGN(rxlen, 4) + 8); + + if (netif_msg_pktdata(ks)) + ks8851_dbg_dumpkkt(ks, rxpkt); + + skb->protocol = eth_type_trans(skb, ks->netdev); + netif_rx(skb); + + ks->netdev->stats.rx_packets++; + ks->netdev->stats.rx_bytes += rxlen - 4; + } + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + } +} + +/** + * ks8851_irq_work - work queue handler for dealing with interrupt requests + * @work: The work structure that was scheduled by schedule_work() + * + * This is the handler invoked when the ks8851_irq() is called to find out + * what happened, as we cannot allow ourselves to sleep whilst waiting for + * anything other process has the chip's lock. + * + * Read the interrupt status, work out what needs to be done and then clear + * any of the interrupts that are not needed. + */ +static void ks8851_irq_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work); + unsigned status; + unsigned handled = 0; + + mutex_lock(&ks->lock); + + status = ks8851_rdreg16(ks, KS_ISR); + + if (netif_msg_intr(ks)) + dev_dbg(&ks->spidev->dev, "%s: status 0x%04x\n", + __func__, status); + + if (status & IRQ_LCI) { + /* should do something about checking link status */ + handled |= IRQ_LCI; + } + + if (status & IRQ_LDI) { + u16 pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_WKEVT_MASK; + ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK); + + handled |= IRQ_LDI; + } + + if (status & IRQ_RXPSI) + handled |= IRQ_RXPSI; + + if (status & IRQ_TXI) { + handled |= IRQ_TXI; + + /* no lock here, tx queue should have been stopped */ + + /* update our idea of how much tx space is available to the + * system */ + ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR); + + if (netif_msg_intr(ks)) + ks_dbg(ks, "%s: txspace %d\n", __func__, ks->tx_space); + } + + if (status & IRQ_RXI) + handled |= IRQ_RXI; + + if (status & IRQ_SPIBEI) { + dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__); + handled |= IRQ_SPIBEI; + } + + ks8851_wrreg16(ks, KS_ISR, handled); + + if (status & IRQ_RXI) { + /* the datasheet says to disable the rx interrupt during + * packet read-out, however we're masking the interrupt + * from the device so do not bother masking just the RX + * from the device. */ + + ks8851_rx_pkts(ks); + } + + /* if something stopped the rx process, probably due to wanting + * to change the rx settings, then do something about restarting + * it. */ + if (status & IRQ_RXPSI) { + struct ks8851_rxctrl *rxc = &ks->rxctrl; + + /* update the multicast hash table */ + ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]); + ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]); + ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]); + ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]); + + ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2); + ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1); + } + + mutex_unlock(&ks->lock); + + if (status & IRQ_TXI) + netif_wake_queue(ks->netdev); + + enable_irq(ks->netdev->irq); +} + +/** + * calc_txlen - calculate size of message to send packet + * @len: Lenght of data + * + * Returns the size of the TXFIFO message needed to send + * this packet. + */ +static inline unsigned calc_txlen(unsigned len) +{ + return ALIGN(len + 4, 4); +} + +/** + * ks8851_wrpkt - write packet to TX FIFO + * @ks: The device state. + * @txp: The sk_buff to transmit. + * @irq: IRQ on completion of the packet. + * + * Send the @txp to the chip. This means creating the relevant packet header + * specifying the length of the packet and the other information the chip + * needs, such as IRQ on completion. Send the header and the packet data to + * the device. + */ +static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + unsigned fid = 0; + int ret; + + if (netif_msg_tx_queued(ks)) + dev_dbg(&ks->spidev->dev, "%s: skb %p, %d@%p, irq %d\n", + __func__, txp, txp->len, txp->data, irq); + + fid = ks->fid++; + fid &= TXFR_TXFID_MASK; + + if (irq) + fid |= TXFR_TXIC; /* irq on completion */ + + /* start header at txb[1] to align txw entries */ + ks->txh.txb[1] = KS_SPIOP_TXFIFO; + ks->txh.txw[1] = cpu_to_le16(fid); + ks->txh.txw[2] = cpu_to_le16(txp->len); + + xfer->tx_buf = &ks->txh.txb[1]; + xfer->rx_buf = NULL; + xfer->len = 5; + + xfer++; + xfer->tx_buf = txp->data; + xfer->rx_buf = NULL; + xfer->len = ALIGN(txp->len, 4); + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + ks_err(ks, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_done_tx - update and then free skbuff after transmitting + * @ks: The device state + * @txb: The buffer transmitted + */ +static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb) +{ + struct net_device *dev = ks->netdev; + + dev->stats.tx_bytes += txb->len; + dev->stats.tx_packets++; + + dev_kfree_skb(txb); +} + +/** + * ks8851_tx_work - process tx packet(s) + * @work: The work strucutre what was scheduled. + * + * This is called when a number of packets have been scheduled for + * transmission and need to be sent to the device. + */ +static void ks8851_tx_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work); + struct sk_buff *txb; + bool last = false; + + mutex_lock(&ks->lock); + + while (!last) { + txb = skb_dequeue(&ks->txq); + last = skb_queue_empty(&ks->txq); + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA); + ks8851_wrpkt(ks, txb, last); + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE); + + ks8851_done_tx(ks, txb); + } + + mutex_unlock(&ks->lock); +} + +/** + * ks8851_set_powermode - set power mode of the device + * @ks: The device state + * @pwrmode: The power mode value to write to KS_PMECR. + * + * Change the power mode of the chip. + */ +static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode) +{ + unsigned pmecr; + + if (netif_msg_hw(ks)) + ks_dbg(ks, "setting power mode %d\n", pwrmode); + + pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_PM_MASK; + pmecr |= pwrmode; + + ks8851_wrreg16(ks, KS_PMECR, pmecr); +} + +/** + * ks8851_net_open - open network device + * @dev: The network device being opened. + * + * Called when the network device is marked active, such as a user executing + * 'ifconfig up' on the device. + */ +static int ks8851_net_open(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + /* lock the card, even if we may not actually be doing anything + * else at the moment */ + mutex_lock(&ks->lock); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "opening %s\n", dev->name); + + /* bring chip out of any power saving mode it was in */ + ks8851_set_powermode(ks, PMECR_PM_NORMAL); + + /* issue a soft reset to the RX/TX QMU to put it into a known + * state. */ + ks8851_soft_reset(ks, GRR_QMU); + + /* setup transmission parameters */ + + ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */ + TXCR_TXPE | /* pad to min length */ + TXCR_TXCRC | /* add CRC */ + TXCR_TXFCE)); /* enable flow control */ + + /* auto-increment tx data, reset tx pointer */ + ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI); + + /* setup receiver control */ + + ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */ + RXCR1_RXFCE | /* enable flow control */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXUE | /* unicast enable */ + RXCR1_RXE)); /* enable rx block */ + + /* transfer entire frames out in one go */ + ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME); + + /* set receive counter timeouts */ + ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */ + ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */ + ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */ + + ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */ + RXQCR_RXDBCTE | /* IRQ on byte count exceeded */ + RXQCR_RXDTTE); /* IRQ on time exceeded */ + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + + /* clear then enable interrupts */ + +#define STD_IRQ (IRQ_LCI | /* Link Change */ \ + IRQ_TXI | /* TX done */ \ + IRQ_RXI | /* RX done */ \ + IRQ_SPIBEI | /* SPI bus error */ \ + IRQ_TXPSI | /* TX process stop */ \ + IRQ_RXPSI) /* RX process stop */ + + ks->rc_ier = STD_IRQ; + ks8851_wrreg16(ks, KS_ISR, STD_IRQ); + ks8851_wrreg16(ks, KS_IER, STD_IRQ); + + netif_start_queue(ks->netdev); + + if (netif_msg_ifup(ks)) + ks_dbg(ks, "network device %s up\n", dev->name); + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_net_stop - close network device + * @dev: The device being closed. + * + * Called to close down a network device which has been active. Cancell any + * work, shutdown the RX and TX process and then place the chip into a low + * power state whilst it is not being used. + */ +static int ks8851_net_stop(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (netif_msg_ifdown(ks)) + ks_info(ks, "%s: shutting down\n", dev->name); + + netif_stop_queue(dev); + + mutex_lock(&ks->lock); + + /* stop any outstanding work */ + flush_work(&ks->irq_work); + flush_work(&ks->tx_work); + flush_work(&ks->rxctrl_work); + + /* turn off the IRQs and ack any outstanding */ + ks8851_wrreg16(ks, KS_IER, 0x0000); + ks8851_wrreg16(ks, KS_ISR, 0xffff); + + /* shutdown RX process */ + ks8851_wrreg16(ks, KS_RXCR1, 0x0000); + + /* shutdown TX process */ + ks8851_wrreg16(ks, KS_TXCR, 0x0000); + + /* set powermode to soft power down to save power */ + ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + + /* ensure any queued tx buffers are dumped */ + while (!skb_queue_empty(&ks->txq)) { + struct sk_buff *txb = skb_dequeue(&ks->txq); + + if (netif_msg_ifdown(ks)) + ks_dbg(ks, "%s: freeing txb %p\n", __func__, txb); + + dev_kfree_skb(txb); + } + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_start_xmit - transmit packet + * @skb: The buffer to transmit + * @dev: The device used to transmit the packet. + * + * Called by the network layer to transmit the @skb. Queue the packet for + * the device and schedule the necessary work to transmit the packet when + * it is free. + * + * We do this to firstly avoid sleeping with the network device locked, + * and secondly so we can round up more than one packet to transmit which + * means we can try and avoid generating too many transmit done interrupts. + */ +static int ks8851_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + unsigned needed = calc_txlen(skb->len); + int ret = NETDEV_TX_OK; + + if (netif_msg_tx_queued(ks)) + ks_dbg(ks, "%s: skb %p, %d@%p\n", __func__, + skb, skb->len, skb->data); + + spin_lock(&ks->statelock); + + if (needed > ks->tx_space) { + netif_stop_queue(dev); + ret = NETDEV_TX_BUSY; + } else { + ks->tx_space -= needed; + skb_queue_tail(&ks->txq, skb); + } + + spin_unlock(&ks->statelock); + schedule_work(&ks->tx_work); + + return ret; +} + +/** + * ks8851_rxctrl_work - work handler to change rx mode + * @work: The work structure this belongs to. + * + * Lock the device and issue the necessary changes to the receive mode from + * the network device layer. This is done so that we can do this without + * having to sleep whilst holding the network device lock. + * + * Since the recommendation from Micrel is that the RXQ is shutdown whilst the + * receive parameters are programmed, we issue a write to disable the RXQ and + * then wait for the interrupt handler to be triggered once the RXQ shutdown is + * complete. The interrupt handler then writes the new values into the chip. + */ +static void ks8851_rxctrl_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work); + + mutex_lock(&ks->lock); + + /* need to shutdown RXQ before modifying filter parameters */ + ks8851_wrreg16(ks, KS_RXCR1, 0x00); + + mutex_unlock(&ks->lock); +} + +static void ks8851_set_rx_mode(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + struct ks8851_rxctrl rxctrl; + + memset(&rxctrl, 0, sizeof(rxctrl)); + + if (dev->flags & IFF_PROMISC) { + /* interface to receive everything */ + + rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF; + } else if (dev->flags & IFF_ALLMULTI) { + /* accept all multicast packets */ + + rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE | + RXCR1_RXPAFMA | RXCR1_RXMAFMA); + } else if (dev->flags & IFF_MULTICAST && dev->mc_count > 0) { + struct dev_mc_list *mcptr = dev->mc_list; + u32 crc; + int i; + + /* accept some multicast */ + + for (i = dev->mc_count; i > 0; i--) { + crc = ether_crc(ETH_ALEN, mcptr->dmi_addr); + crc >>= (32 - 6); /* get top six bits */ + + rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf)); + mcptr = mcptr->next; + } + + rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXAE | RXCR1_RXPAFMA; + } else { + /* just accept broadcast / unicast */ + rxctrl.rxcr1 = RXCR1_RXPAFMA; + } + + rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXE | /* RX process enable */ + RXCR1_RXFCE); /* enable flow control */ + + rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME; + + /* schedule work to do the actual set of the data if needed */ + + spin_lock(&ks->statelock); + + if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) { + memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl)); + schedule_work(&ks->rxctrl_work); + } + + spin_unlock(&ks->statelock); +} + +static int ks8851_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *sa = addr; + + if (netif_running(dev)) + return -EBUSY; + + if (!is_valid_ether_addr(sa->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN); + return ks8851_write_mac_addr(dev); +} + +static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (!netif_running(dev)) + return -EINVAL; + + return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL); +} + +static const struct net_device_ops ks8851_netdev_ops = { + .ndo_open = ks8851_net_open, + .ndo_stop = ks8851_net_stop, + .ndo_do_ioctl = ks8851_net_ioctl, + .ndo_start_xmit = ks8851_start_xmit, + .ndo_set_mac_address = ks8851_set_mac_address, + .ndo_set_rx_mode = ks8851_set_rx_mode, + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, +}; + +/* ethtool support */ + +static void ks8851_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *di) +{ + strlcpy(di->driver, "KS8851", sizeof(di->driver)); + strlcpy(di->version, "1.00", sizeof(di->version)); + strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info)); +} + +static u32 ks8851_get_msglevel(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return ks->msg_enable; +} + +static void ks8851_set_msglevel(struct net_device *dev, u32 to) +{ + struct ks8851_net *ks = netdev_priv(dev); + ks->msg_enable = to; +} + +static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_gset(&ks->mii, cmd); +} + +static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_sset(&ks->mii, cmd); +} + +static u32 ks8851_get_link(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_link_ok(&ks->mii); +} + +static int ks8851_nway_reset(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_nway_restart(&ks->mii); +} + +static const struct ethtool_ops ks8851_ethtool_ops = { + .get_drvinfo = ks8851_get_drvinfo, + .get_msglevel = ks8851_get_msglevel, + .set_msglevel = ks8851_set_msglevel, + .get_settings = ks8851_get_settings, + .set_settings = ks8851_set_settings, + .get_link = ks8851_get_link, + .nway_reset = ks8851_nway_reset, +}; + +/* MII interface controls */ + +/** + * ks8851_phy_reg - convert MII register into a KS8851 register + * @reg: MII register number. + * + * Return the KS8851 register number for the corresponding MII PHY register + * if possible. Return zero if the MII register has no direct mapping to the + * KS8851 register set. + */ +static int ks8851_phy_reg(int reg) +{ + switch (reg) { + case MII_BMCR: + return KS_P1MBCR; + case MII_BMSR: + return KS_P1MBSR; + case MII_PHYSID1: + return KS_PHY1ILR; + case MII_PHYSID2: + return KS_PHY1IHR; + case MII_ADVERTISE: + return KS_P1ANAR; + case MII_LPA: + return KS_P1ANLPR; + } + + return 0x0; +} + +/** + * ks8851_phy_read - MII interface PHY register read. + * @dev: The network device the PHY is on. + * @phy_addr: Address of PHY (ignored as we only have one) + * @reg: The register to read. + * + * This call reads data from the PHY register specified in @reg. Since the + * device does not support all the MII registers, the non-existant values + * are always returned as zero. + * + * We return zero for unsupported registers as the MII code does not check + * the value returned for any error status, and simply returns it to the + * caller. The mii-tool that the driver was tested with takes any -ve error + * as real PHY capabilities, thus displaying incorrect data to the user. + */ +static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + int result; + + ksreg = ks8851_phy_reg(reg); + if (!ksreg) + return 0x0; /* no error return allowed, so use zero */ + + mutex_lock(&ks->lock); + result = ks8851_rdreg16(ks, ksreg); + mutex_unlock(&ks->lock); + + return result; +} + +static void ks8851_phy_write(struct net_device *dev, + int phy, int reg, int value) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + + ksreg = ks8851_phy_reg(reg); + if (ksreg) { + mutex_lock(&ks->lock); + ks8851_wrreg16(ks, ksreg, value); + mutex_unlock(&ks->lock); + } +} + +/** + * ks8851_read_selftest - read the selftest memory info. + * @ks: The device state + * + * Read and check the TX/RX memory selftest information. + */ +static int ks8851_read_selftest(struct ks8851_net *ks) +{ + unsigned both_done = MBIR_TXMBF | MBIR_RXMBF; + int ret = 0; + unsigned rd; + + rd = ks8851_rdreg16(ks, KS_MBIR); + + if ((rd & both_done) != both_done) { + ks_warn(ks, "Memory selftest not finished\n"); + return 0; + } + + if (rd & MBIR_TXMBFA) { + ks_err(ks, "TX memory selftest fail\n"); + ret |= 1; + } + + if (rd & MBIR_RXMBFA) { + ks_err(ks, "RX memory selftest fail\n"); + ret |= 2; + } + + return 0; +} + +/* driver bus management functions */ + +static int __devinit ks8851_probe(struct spi_device *spi) +{ + struct net_device *ndev; + struct ks8851_net *ks; + int ret; + + ndev = alloc_etherdev(sizeof(struct ks8851_net)); + if (!ndev) { + dev_err(&spi->dev, "failed to alloc ethernet device\n"); + return -ENOMEM; + } + + spi->bits_per_word = 8; + + ks = netdev_priv(ndev); + + ks->netdev = ndev; + ks->spidev = spi; + ks->tx_space = 6144; + + mutex_init(&ks->lock); + spin_lock_init(&ks->statelock); + + INIT_WORK(&ks->tx_work, ks8851_tx_work); + INIT_WORK(&ks->irq_work, ks8851_irq_work); + INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work); + + /* initialise pre-made spi transfer messages */ + + spi_message_init(&ks->spi_msg1); + spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1); + + spi_message_init(&ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2); + + /* setup mii state */ + ks->mii.dev = ndev; + ks->mii.phy_id = 1, + ks->mii.phy_id_mask = 1; + ks->mii.reg_num_mask = 0xf; + ks->mii.mdio_read = ks8851_phy_read; + ks->mii.mdio_write = ks8851_phy_write; + + dev_info(&spi->dev, "message enable is %d\n", msg_enable); + + /* set the default message enable */ + ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV | + NETIF_MSG_PROBE | + NETIF_MSG_LINK)); + + skb_queue_head_init(&ks->txq); + + SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops); + SET_NETDEV_DEV(ndev, &spi->dev); + + dev_set_drvdata(&spi->dev, ks); + + ndev->if_port = IF_PORT_100BASET; + ndev->netdev_ops = &ks8851_netdev_ops; + ndev->irq = spi->irq; + + /* simple check for a valid chip being connected to the bus */ + + if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) { + dev_err(&spi->dev, "failed to read device ID\n"); + ret = -ENODEV; + goto err_id; + } + + ks8851_read_selftest(ks); + ks8851_init_mac(ks); + + ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW, + ndev->name, ks); + if (ret < 0) { + dev_err(&spi->dev, "failed to get irq\n"); + goto err_irq; + } + + ret = register_netdev(ndev); + if (ret) { + dev_err(&spi->dev, "failed to register network device\n"); + goto err_netdev; + } + + dev_info(&spi->dev, "revision %d, MAC %pM, IRQ %d\n", + CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)), + ndev->dev_addr, ndev->irq); + + return 0; + + +err_netdev: + free_irq(ndev->irq, ndev); + +err_id: +err_irq: + free_netdev(ndev); + return ret; +} + +static int __devexit ks8851_remove(struct spi_device *spi) +{ + struct ks8851_net *priv = dev_get_drvdata(&spi->dev); + + if (netif_msg_drv(priv)) + dev_info(&spi->dev, "remove"); + + unregister_netdev(priv->netdev); + free_irq(spi->irq, priv); + free_netdev(priv->netdev); + + return 0; +} + +static struct spi_driver ks8851_driver = { + .driver = { + .name = "ks8851", + .owner = THIS_MODULE, + }, + .probe = ks8851_probe, + .remove = __devexit_p(ks8851_remove), +}; + +static int __init ks8851_init(void) +{ + return spi_register_driver(&ks8851_driver); +} + +static void __exit ks8851_exit(void) +{ + spi_unregister_driver(&ks8851_driver); +} + +module_init(ks8851_init); +module_exit(ks8851_exit); + +MODULE_DESCRIPTION("KS8851 Network driver"); +MODULE_AUTHOR("Ben Dooks "); +MODULE_LICENSE("GPL"); + +module_param_named(message, msg_enable, int, 0); +MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)"); Index: b/drivers/net/ks8851.h =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ b/drivers/net/ks8851.h 2009-07-16 10:49:18.000000000 +0100 @@ -0,0 +1,296 @@ +/* drivers/net/ks8851.h + * + * Copyright 2009 Simtec Electronics + * Ben Dooks + * + * KS8851 register definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define KS_CCR 0x08 +#define CCR_EEPROM (1 << 9) +#define CCR_SPI (1 << 8) +#define CCR_32PIN (1 << 0) + +/* MAC address registers */ +#define KS_MARL 0x10 +#define KS_MARM 0x12 +#define KS_MARH 0x14 + +#define KS_OBCR 0x20 +#define OBCR_ODS_16mA (1 << 6) + +#define KS_EEPCR 0x22 +#define EEPCR_EESA (1 << 4) +#define EEPCR_EESB (1 << 3) +#define EEPCR_EEDO (1 << 2) +#define EEPCR_EESCK (1 << 1) +#define EEPCR_EECS (1 << 0) + +#define KS_MBIR 0x24 +#define MBIR_TXMBF (1 << 12) +#define MBIR_TXMBFA (1 << 11) +#define MBIR_RXMBF (1 << 4) +#define MBIR_RXMBFA (1 << 3) + +#define KS_GRR 0x26 +#define GRR_QMU (1 << 1) +#define GRR_GSR (1 << 0) + +#define KS_WFCR 0x2A +#define WFCR_MPRXE (1 << 7) +#define WFCR_WF3E (1 << 3) +#define WFCR_WF2E (1 << 2) +#define WFCR_WF1E (1 << 1) +#define WFCR_WF0E (1 << 0) + +#define KS_WF0CRC0 0x30 +#define KS_WF0CRC1 0x32 +#define KS_WF0BM0 0x34 +#define KS_WF0BM1 0x36 +#define KS_WF0BM2 0x38 +#define KS_WF0BM3 0x3A + +#define KS_WF1CRC0 0x40 +#define KS_WF1CRC1 0x42 +#define KS_WF1BM0 0x44 +#define KS_WF1BM1 0x46 +#define KS_WF1BM2 0x48 +#define KS_WF1BM3 0x4A + +#define KS_WF2CRC0 0x50 +#define KS_WF2CRC1 0x52 +#define KS_WF2BM0 0x54 +#define KS_WF2BM1 0x56 +#define KS_WF2BM2 0x58 +#define KS_WF2BM3 0x5A + +#define KS_WF3CRC0 0x60 +#define KS_WF3CRC1 0x62 +#define KS_WF3BM0 0x64 +#define KS_WF3BM1 0x66 +#define KS_WF3BM2 0x68 +#define KS_WF3BM3 0x6A + +#define KS_TXCR 0x70 +#define TXCR_TCGICMP (1 << 8) +#define TXCR_TCGUDP (1 << 7) +#define TXCR_TCGTCP (1 << 6) +#define TXCR_TCGIP (1 << 5) +#define TXCR_FTXQ (1 << 4) +#define TXCR_TXFCE (1 << 3) +#define TXCR_TXPE (1 << 2) +#define TXCR_TXCRC (1 << 1) +#define TXCR_TXE (1 << 0) + +#define KS_TXSR 0x72 +#define TXSR_TXLC (1 << 13) +#define TXSR_TXMC (1 << 12) +#define TXSR_TXFID_MASK (0x3f << 0) +#define TXSR_TXFID_SHIFT (0) +#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f) + +#define KS_RXCR1 0x74 +#define RXCR1_FRXQ (1 << 15) +#define RXCR1_RXUDPFCC (1 << 14) +#define RXCR1_RXTCPFCC (1 << 13) +#define RXCR1_RXIPFCC (1 << 12) +#define RXCR1_RXPAFMA (1 << 11) +#define RXCR1_RXFCE (1 << 10) +#define RXCR1_RXEFE (1 << 9) +#define RXCR1_RXMAFMA (1 << 8) +#define RXCR1_RXBE (1 << 7) +#define RXCR1_RXME (1 << 6) +#define RXCR1_RXUE (1 << 5) +#define RXCR1_RXAE (1 << 4) +#define RXCR1_RXINVF (1 << 1) +#define RXCR1_RXE (1 << 0) + +#define KS_RXCR2 0x76 +#define RXCR2_SRDBL_MASK (0x7 << 5) +#define RXCR2_SRDBL_SHIFT (5) +#define RXCR2_SRDBL_4B (0x0 << 5) +#define RXCR2_SRDBL_8B (0x1 << 5) +#define RXCR2_SRDBL_16B (0x2 << 5) +#define RXCR2_SRDBL_32B (0x3 << 5) +#define RXCR2_SRDBL_FRAME (0x4 << 5) +#define RXCR2_IUFFP (1 << 4) +#define RXCR2_RXIUFCEZ (1 << 3) +#define RXCR2_UDPLFE (1 << 2) +#define RXCR2_RXICMPFCC (1 << 1) +#define RXCR2_RXSAF (1 << 0) + +#define KS_TXMIR 0x78 + +#define KS_RXFHSR 0x7C +#define RXFSHR_RXFV (1 << 15) +#define RXFSHR_RXICMPFCS (1 << 13) +#define RXFSHR_RXIPFCS (1 << 12) +#define RXFSHR_RXTCPFCS (1 << 11) +#define RXFSHR_RXUDPFCS (1 << 10) +#define RXFSHR_RXBF (1 << 7) +#define RXFSHR_RXMF (1 << 6) +#define RXFSHR_RXUF (1 << 5) +#define RXFSHR_RXMR (1 << 4) +#define RXFSHR_RXFT (1 << 3) +#define RXFSHR_RXFTL (1 << 2) +#define RXFSHR_RXRF (1 << 1) +#define RXFSHR_RXCE (1 << 0) + +#define KS_RXFHBCR 0x7E +#define KS_TXQCR 0x80 +#define TXQCR_AETFE (1 << 2) +#define TXQCR_TXQMAM (1 << 1) +#define TXQCR_METFE (1 << 0) + +#define KS_RXQCR 0x82 +#define RXQCR_RXDTTS (1 << 12) +#define RXQCR_RXDBCTS (1 << 11) +#define RXQCR_RXFCTS (1 << 10) +#define RXQCR_RXIPHTOE (1 << 9) +#define RXQCR_RXDTTE (1 << 7) +#define RXQCR_RXDBCTE (1 << 6) +#define RXQCR_RXFCTE (1 << 5) +#define RXQCR_ADRFE (1 << 4) +#define RXQCR_SDA (1 << 3) +#define RXQCR_RRXEF (1 << 0) + +#define KS_TXFDPR 0x84 +#define TXFDPR_TXFPAI (1 << 14) +#define TXFDPR_TXFP_MASK (0x7ff << 0) +#define TXFDPR_TXFP_SHIFT (0) + +#define KS_RXFDPR 0x86 +#define RXFDPR_RXFPAI (1 << 14) + +#define KS_RXDTTR 0x8C +#define KS_RXDBCTR 0x8E + +#define KS_IER 0x90 +#define KS_ISR 0x92 +#define IRQ_LCI (1 << 15) +#define IRQ_TXI (1 << 14) +#define IRQ_RXI (1 << 13) +#define IRQ_RXOI (1 << 11) +#define IRQ_TXPSI (1 << 9) +#define IRQ_RXPSI (1 << 8) +#define IRQ_TXSAI (1 << 6) +#define IRQ_RXWFDI (1 << 5) +#define IRQ_RXMPDI (1 << 4) +#define IRQ_LDI (1 << 3) +#define IRQ_EDI (1 << 2) +#define IRQ_SPIBEI (1 << 1) +#define IRQ_DEDI (1 << 0) + +#define KS_RXFCTR 0x9C +#define KS_RXFC 0x9D +#define RXFCTR_RXFC_MASK (0xff << 8) +#define RXFCTR_RXFC_SHIFT (8) +#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff) +#define RXFCTR_RXFCT_MASK (0xff << 0) +#define RXFCTR_RXFCT_SHIFT (0) + +#define KS_TXNTFSR 0x9E + +#define KS_MAHTR0 0xA0 +#define KS_MAHTR1 0xA2 +#define KS_MAHTR2 0xA4 +#define KS_MAHTR3 0xA6 + +#define KS_FCLWR 0xB0 +#define KS_FCHWR 0xB2 +#define KS_FCOWR 0xB4 + +#define KS_CIDER 0xC0 +#define CIDER_ID 0x8870 +#define CIDER_REV_MASK (0x7 << 1) +#define CIDER_REV_SHIFT (1) +#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7) + +#define KS_CGCR 0xC6 + +#define KS_IACR 0xC8 +#define IACR_RDEN (1 << 12) +#define IACR_TSEL_MASK (0x3 << 10) +#define IACR_TSEL_SHIFT (10) +#define IACR_TSEL_MIB (0x3 << 10) +#define IACR_ADDR_MASK (0x1f << 0) +#define IACR_ADDR_SHIFT (0) + +#define KS_IADLR 0xD0 +#define KS_IAHDR 0xD2 + +#define KS_PMECR 0xD4 +#define PMECR_PME_DELAY (1 << 14) +#define PMECR_PME_POL (1 << 12) +#define PMECR_WOL_WAKEUP (1 << 11) +#define PMECR_WOL_MAGICPKT (1 << 10) +#define PMECR_WOL_LINKUP (1 << 9) +#define PMECR_WOL_ENERGY (1 << 8) +#define PMECR_AUTO_WAKE_EN (1 << 7) +#define PMECR_WAKEUP_NORMAL (1 << 6) +#define PMECR_WKEVT_MASK (0xf << 2) +#define PMECR_WKEVT_SHIFT (2) +#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf) +#define PMECR_WKEVT_ENERGY (0x1 << 2) +#define PMECR_WKEVT_LINK (0x2 << 2) +#define PMECR_WKEVT_MAGICPKT (0x4 << 2) +#define PMECR_WKEVT_FRAME (0x8 << 2) +#define PMECR_PM_MASK (0x3 << 0) +#define PMECR_PM_SHIFT (0) +#define PMECR_PM_NORMAL (0x0 << 0) +#define PMECR_PM_ENERGY (0x1 << 0) +#define PMECR_PM_SOFTDOWN (0x2 << 0) +#define PMECR_PM_POWERSAVE (0x3 << 0) + +/* Standard MII PHY data */ +#define KS_P1MBCR 0xE4 +#define KS_P1MBSR 0xE6 +#define KS_PHY1ILR 0xE8 +#define KS_PHY1IHR 0xEA +#define KS_P1ANAR 0xEC +#define KS_P1ANLPR 0xEE + +#define KS_P1SCLMD 0xF4 +#define P1SCLMD_LEDOFF (1 << 15) +#define P1SCLMD_TXIDS (1 << 14) +#define P1SCLMD_RESTARTAN (1 << 13) +#define P1SCLMD_DISAUTOMDIX (1 << 10) +#define P1SCLMD_FORCEMDIX (1 << 9) +#define P1SCLMD_AUTONEGEN (1 << 7) +#define P1SCLMD_FORCE100 (1 << 6) +#define P1SCLMD_FORCEFDX (1 << 5) +#define P1SCLMD_ADV_FLOW (1 << 4) +#define P1SCLMD_ADV_100BT_FDX (1 << 3) +#define P1SCLMD_ADV_100BT_HDX (1 << 2) +#define P1SCLMD_ADV_10BT_FDX (1 << 1) +#define P1SCLMD_ADV_10BT_HDX (1 << 0) + +#define KS_P1CR 0xF6 +#define P1CR_HP_MDIX (1 << 15) +#define P1CR_REV_POL (1 << 13) +#define P1CR_OP_100M (1 << 10) +#define P1CR_OP_FDX (1 << 9) +#define P1CR_OP_MDI (1 << 7) +#define P1CR_AN_DONE (1 << 6) +#define P1CR_LINK_GOOD (1 << 5) +#define P1CR_PNTR_FLOW (1 << 4) +#define P1CR_PNTR_100BT_FDX (1 << 3) +#define P1CR_PNTR_100BT_HDX (1 << 2) +#define P1CR_PNTR_10BT_FDX (1 << 1) +#define P1CR_PNTR_10BT_HDX (1 << 0) + +/* TX Frame control */ + +#define TXFR_TXIC (1 << 15) +#define TXFR_TXFID_MASK (0x3f << 0) +#define TXFR_TXFID_SHIFT (0) + +/* SPI frame opcodes */ +#define KS_SPIOP_RD (0x00) +#define KS_SPIOP_WR (0x40) +#define KS_SPIOP_RXFIFO (0x80) +#define KS_SPIOP_TXFIFO (0xC0) -- Ben (ben@fluff.org, http://www.fluff.org/) 'a smiley only costs 4 bytes' -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html